Bogen Rpk88 Guide

Specifications subject to change without notice.

54-2146-01E 1108

RPK88 Rack Mount Kit

Installation and Use Manual

The RPK88 Rack Mount Kit is designed to flush mount the modules of a PCM system. The RPK88 will hold up to

ten modules in two assemblies. The RPK88 allows easy mounting of these modules in a standard 19-inch audio

rack (the RPK88 is six rack spaces high). The kit includes twelve wiring saddles, eight mounting brackets, and eight

#6 x 1/4” screws.

RPK88 Mounting Plate

Mounting

Brackets (8)

Wiring

Saddles (12)

Knock-out panels (nine total)

START HERE

(Panel left open)

Knock-out panel for power supply

power cord (as needed, two total)

Knock-out panels for wiring

access (as needed, six total)

Remove additional panels to fit

assembled module(s) (beginning

here, then work left to right)

Plug wiring saddles into any of

12 staggered holes as needed

Remove appropriate knock-

out panels.

Six

Modules

Max.

Four

Modules

Max.

#6 x 1/4”

Screws (8)

Attach mounting brackets to

top and bottom corners of

module assembly.

Use screws included with

modules.

Attach module assembly

to RPK88 using #6 x 1/4”

screws.

See PCM system instructions

for module assembly.

50 Spring Street, Ramsey, NJ 07446

Tel. 201-934-8500 • Fax: 201-934-9832

www.bogen.com

LIMITED WARRANTY; EXCLUSION OF CERTAIN DAMAGES

The Bogen RPK88 is warranted to be free from defects in material or workmanship for two (2) years from the date of sale to the original purchaser. Any part of the product cov-

ered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured

and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid. This warranty does not

extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or have been modified or repaired or altered

in any manner whatsoever, or where the serial number or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY. BOGEN

MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability arising out of the manufac-

ture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT

SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA

OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POS-

SIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclu-

sion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department — same address as above or call 201-934-8500. The parts and labor involved

in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and labor charges will be at the

owner's expense. All returns require a Return Authorization number.

7/22/2008

Completed Assembly Examples

A nine-zone PCM system with talk-back capability:

Wire saddles

(as needed)

Remove for wire

access (as needed)

Remove for power

supply plug

Two nine-zone slave assemblies:

A 15-zone PCM system without talk-back