boink Inmate QX7 User manual

QX7
Inmate Mounting Instructions
VER 4
January 25, 2006

TOOLS REQUIRED FOR THE
INSTALLATION
ITEM DESCRIPTION QTY
1 KIOSK QX7 1
2 BACK MOUNT FRAME 1
3 POWER DRILL 1
4 1/4” BIT 1
5 HAMMER 1
6 CONCRETE DROP-IN ANCHORS (FEMALE) 12
7 HEX BOLTS 1/4” X 3/4 12
8 7/16” WRENCH 1
SUPPORT FRAME
PAGE 2 OF 21

QX7 Kiosk
Frontal View
PAGE 3 OF 21

TOP VIEW
FRONT VIEW LATERAL VIEW
PAGE 4 OF 21

QX7 MOUNTING FRAME
PAGE 5 OF 21

PAGE 6 OF 21

QX7 Inmate Mounting
Measured from the floor in front of the device.
PAGE 7 OF 21

PAGE 8 OF 21

ELECTRIC AND DATA
INSTALLATION SPECIFICATIONS
VPN
ACCESS
HUB
ETHERNET OR DSL
CONNECTION
QX7
CONVENTIONS
SURFACE RACEWAY
SURFACE JUNCTION BOX
POWER
DOUBLE OUTLET UTP-CATEGORY 5
REGULATED-DOUBLE STRAIGHT
BLADE RECEPTACLE 15 Amp 125V
PAGE 9 OF 21

Height for data and power outlets
The power strip should be flat on the wall to avoid any
interference with the kiosk to be plugged in.
PAGE 10 OF 21

HOW TO INSTALL
THE BACK MOUNT FRAME
PAGE 11 OF 21
FIX TO
THE
WALL
KIOSK
FASTENING
SLOT
QX7 BOLT POSITION FLOOR

Holes to insert the tubes through
1. Locate the holes to insert the electrical and data tubes through either the ceil-
ing or the floor depending where the cables come out from.
PAGE 12 OF 21
REFERENCE
POINT
2. Find the reference point.

PAGE 13 OF 21
REFERENCE POINT

Support frame point of
reference
3. Mark all (12) points to fix the support frame to the wall and drill it with a 1/4” bit. In-
stall the anchor; drop it into a pre-drilled hole and then expand it using a setting tool.
REFERENCE
POINT
Concrete Drop-In Anchors are
female anchors designed for use
in concrete. The anchor is dropped
into a pre drilled hole and then
expanded using a setting tool.
PAGE 14 OF 21

4. (a) Drill hole into the concrete with a carbide tipped masonry drill bit . Make sure
hole depth is 1”.
(b) Clean out concrete dust from hole using a wire brush, compressed air or a blow out
bulb.
(c) Drive anchor into the hole, flush with the surface of the concrete.
(d) Using the proper setting tool for the anchor, expand anchor by inserting the set-
ting tool into the anchor and set with several solid hammer blows. The anchor is set
properly when shoulder of setting tool is flushed with the top of anchor. To set anchor
below surface; drill hole deeper than anchor length. Thread bolt into anchor. Hammer
anchor into hole until bolt head is at a desired depth.
5. Fix the back-mount frame to the wall with (12) hex bolts 1/4” x 3/4”. Use the 7/16” wrench.
1/4” X 3/4 HEX
BOLT
PAGE 15 OF 21

PAGE 16 OF 21

6. Remove the bottom 1/2” hole cover. You can use one or two tubes.
PAGE 17 OF 21
1/2” HOLE COVERS
7. Insert the 1/2” tube for data and power cables. You can use one or two tubes.
INSERT THE TUBES

8. When the nails are fitted on the back-mount frame, push down on the QX7 kiosk.
PAGE 18 OF 21

PAGE 19 OF 21

POWER AND
DATA OUTLETS
LATERAL VIEW
QX7
BACK MOUNT PLATE
QX7
BOTTOM VIEW
10. Place the bolt in its locked position.
9. Connect the data and power cable.
BOLT
PAGE 20 OF 21