Bomberg BOLT-68 - 3 Hands & GMT Guide

WARRANTY & WATCH CARE

WARRANTY & WATCH CARE

2
CONTENT
WARRANTY & USER INSTRUCTIONS
International warranty Pages 3-4
Special recommendation Pages 5-7
Instructions Model - BOLT-68 - 3 Hands & GMT Pages 9-11
Instructions Model - BOLT-68 - 3 Hands Automatic Pages 13-15
Instructions Model - BOLT-68 - Racing Pages 17-21
Instructions Model - BOLT-68 - Chronograph Pages 23-26
Instructions Model - BOLT-68 - Chronograph Automatic Pages 29-32
BOLT-68 - Bayonet system Pages 35-38

3
INTERNATIONAL WARRANTY
Limited 2 years warranty:
Your Bomberg watch is warranted for a 2 years period under the terms and
conditions of this warranty.
The international Bomberg warranty covers material and manufacturing
defects existing at the time of the delivery of the purchased Bomberg
watch. The warranty only comes into force if the warranty certicate is dated,
fully and correctly completed and stamped by an ofcial Bomberg retailer.
During the warranty period and by presenting the valid warranty certicate,
you will have the right to have any defect repaired free of charge.
This manufacturer’s warranty does not cover:
- The life of the battery;
- Normal wear and tear and aging (scratched crystal, alteration of the
colour and/or material of nonmetallic straps and chains, such as leather,
textile, rubber; peeling of the plating);

4
- Any damage on any part of the watch resulting from abnormal / abusive
use, lack of care, negligence accidents (knocks, dents, crushing, broken
crystal, etc.), incorrect use of the watch and non-observance of the use
directions provided by Bomberg;
- The Bomberg watch handled by non-authorized persons (for battery
replacement, services or repairs) or which has been altered in this
original conditions beyond Bomberg.

5
SPECIAL RECOMMENDATIONS
How often should my watch be checked?
We recommend a yearly water resistancy check (partial service with
movement check).
How often should my watch be serviced?
Like any other precision instrument a watch should be serviced regularly
to ensure perfect runwaring. We cannot say how often you should have
your watch serviced as this depends on the model, the climate where you
live and how you look after the watch yourself. As a rule, a watch should be
serviced every 4 or 5 years, depending on the conditions in which it is worn.
Where should I go to get my watch serviced or for a new battery?
We recommend that you go to an ofcial Bomberg agent or retailer. They
are the only people who have the necessary tools and devices to work on
your watch and to carry out the necessary checks at specialized level.
Furthermore, only specialists can guarantee that their work meets the
stringent quality standards set by Bomberg.

6
What can I do to ensure that my watch functions perfectly for many years?
Magnetic elds: avoid putting your watch on a loud-speaker or a refrige-
rator because these machines create magnetic elds that may damage it.
Salt-Water: always rinse your watch in fresh water after swimming in the sea.
Shocks: avoid subjecting your watch to shocks, including sudden changes
in temperatures.
Screwed crown: always make sure you have screwed the crown properly to
avoid any humidity getting into the mechanism.
Cleaning: use a toothbrush and soapy water to clean bracelet and water
resistancy cases and a soft cloth to dry off afterwards. For the leather
strap, it’s necessary to use special cleaning products.
Chemical products: avoid all direct contact with solvents detergents,
perfume, cosmetics, etc. which may damage the bracelet or strap, the
case or the gaskets.

7
Temperatures: avoid exposing your watch to extreme temperatures (over
60°C or 140°F and under 0°C or 32°F) and to sudden uctuations in tem-
perature.
Water-resistance: All Bomberg watches are water-resistant. They can with-
stand a water pressure of at least 3 bar (depth of 30 meters). Water resistance
is not a permanent condition. To ensure permanent water resistance, the
watch should be checked once a year. To ensure conformance with the war-
ranty regulations, these operations must be performed by an authorized
Bomberg dealer or authorized Bomberg Service Center.
Chronograph pushers: do not adjust the pushers under water as this
could cause wetness in the mechanism.

BOLT-68 - 3 HANDS & GMT

10
BOLT-68 - 3 Hands & GMT
Normal crown position
2nd click position
1st click position
Crown
Second time zone
Minute hand
Second hand
Date*
Hour hand

11
BOMBERG MODEL - BOLT-68 - 3 Hands & GMT
Setting the time:
1. Unscrew and pull the crown out to the 2nd click position so that the
second hand stops.
2. Turn the crown to set the hour and minute hands.
3. After the time has been set, push the crown back to the normal position
and small second hand begins to run again. Screw it in back now.
Setting the date:
1. Unscrew and pull the crown out to the 1st click position.
2. Turn the crown anti-clockwise to set the date.*
3. After the date has been set, push the crown back to the normal position
and screw it in.
Setting the second time zone:
1. Unscrew and pull the crown out to the 1st click position.
2. Turn the crown clockwise to set the second time.
3. After the second time has been set, push the crown back to the normal
position and screw it in.
*Important: It is not possible to adjust the date between 10.30 pm and 0.00 am.
It is necessary to adjust the date after each month with less than 31 days.

BOLT-68 - 3 HANDS AUTOMATIC

14
BOLT-68 - 3 Hands Automatic
Normal crown position
3rd click position
1st click position
Crown
Minute hand
Second hand
Date*
Hour hand
2nd click position

15
BOMBERG MODEL - BOLT-68 - 3 Hands Automatic
Manual winding:
1. Unscrew and pull the crown out to the 1st click position.
2. Turn the crown clockwise to wind the watch..
3. After winding, push the crown back to the normal position and screw it in.
Setting the date:
1. Unscrew and pull the crown out to the intermediate 2nd click position.
2. Turn the crown clockwise to set the date.*
3. After the date has been set, push the crown back to the normal position
and screw it in.
Setting the time:
1. Unscrew and pull the crown out to the 3rd click position so that the
second hand stops.
2. Turn the crown to set the hour and minute hands.
3. After the time has been set, push the crown back to the normal position
and small second hand begins to run again. Screw it in back now.
*Important: It is not possible to adjust the date between 8.00 pm and 3.00 am.
It is necessary to adjust the date after each month with less than 31 days.

BOLT-68 - RACING

18
BOLT-68 - Racing
Normal crown position
2nd click position
1st click position
Crown
Pusher B
Minute hand
Second hand
Chronograph
second hand
Chronograph display:
-1/10 seconds
-10 hours
Hour hand
Pusher A
Chronograph
minute hand