Bosch Rexroth CDT1 Series User manual

RA 17038/02.13
Replaces: 11.12
Hydraulic Cylinder
NFPA Industrial Type
Model CDT1/CGT1
Series 1X
Nominal pressure: Up to 1,500 psi maximum
Technical Data 2
Cylinder Weight 2
Area, Forces, Flow 3
Stroke Tolerances 3
Ordering Details 4
Piston Rod Versions 6
Mounting Type Overview 7
Dimensional Data 8
Double Rod Cylinders 26
Mounting Accessories 28
Cylinder Options 33
Cylinder Application Data 37
Spare Parts 44
1/44
Table of contents Features
Contents Page – Duty, up to 1,500 psi (see chart on page 2)
– Standards, meets or exceeds all JIC and NFPA requirements
– Bore Sizes, 1-1/2” - 8”
– Piston Rods, 1/2" - 5-1/2”
– Mountings,18 standard NFPA mountings
– Ports, SAE o-ring straight thread ports
– Stroke, standard strokes furnished in 1/8” increments. Normal
stroke tolerance + 1/16” / -0”. Closer stroke tolerances avail-
able; consult factory.
– Rod End Threads, standard KK1 male and female threads plus
KK2 oversize male thread. Other rod end styles optional.
– Cushions, available for all bore sizes, at either or both ends.
Project planning software
Interactive Catalog System
Online www.boschrexroth.com/ics

2/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
Standards:
Meets or exceeds all JIC and NFPA requirements.
Nominal pressure: up to 1,500 psi
With extreme shock loads the mounting styles and piston rod
threads have to be considered, taking the fatigue limits into
account.
Maximum operating pressure up to: 1,500 psi
Installation position: Various
Pressure fluid:
Mineral oils (HL, HLP)
Phosphate ester (HFD-R) (–4°F to 300°F)
HFA (41°F to 131°F)
Water glycol HFC (–4°F to 140°F)
Hydraulic fluid temperature range: (-4°F to 176°F)
Viscosity range: 32 to 1760 ssu
Degree of contamination:
Max. permissible degree of contamination of the pressure fluid
is to NAS 1638 class 10.
We therefore recommend a filter with a minium retention rate
of
β10 ≥ 75.
Stroke speed: 20 in/sec
(dependent on the connection port)
Air bleed standard: Secured against removal
2" - 8" bore sizes only
Acceptance:
Each cylinder is tested to Bosch Rexroth standards.
Cylinders, outside the above parameters are also available.
Consult factory
For applications above 230°F specify a non studded piston
rod end and advise operating temperature before ordering.
Under no-load conditions, a minimum pressure of 150 PSI is
recommended for single rod cylinders. In case of lower pres-
sures or double rod cylinders, please consult factory.
Technical Data (for applications outside these parameters, please consult factory)
Operating Pressures (PSI) by Cylinder
Bore Sizes*
Max. psi
Cylinder Standard (max duty
Bore Ø Rod Ø servere
(inches) (inches) service)
1-1/2 1 1,500
2 1 1,500
2-1/2 1 1,500
3-1/4 1 1,500
4 1-3/8 1,000
5 1-3/4 750
6 1-3/4 750
8 2 500
*1) For double rod cylinders, see page 26.
*2) Exceptions to 1,500 psi rating:
a) MF1 and MF2 have maximum operating pressures
of 1,000 psi for 1-1/2" through 4" bore sizes
b) A 2.5" bore with a 5/8" rod has a maximum pressure
rating of 1,000 psi
3) Consult factory for other pressure ratings than
shown above.
4) For stroke lengths above 60 inches, working pressure
may be derated according to buckling load limits.
Consult factory.
Approximate Uncrated CDT1 Hydraulic Cylinder Weights (lbs.)*
Cylinder Bore 1.5 2 2.5 3.25 4 5 6 8
Zero Stroke 5 7 12 20 30 45 70 100
Add Per Inch of Stroke .3 .4 .6 .8 .9 1.0 1.5 2.0
* Weights based on standard (first) rod sizes. Add 10% to cover additional weight for crating.
Project planning software ICS (Interactive Catalog System)
The ICS (Interactive Catalog System) is a selection and project
planning tool for hydraulic cylinders. The ICS allows designers
of machines and systems to quickly and reliably find the perfect
hydraulic cylinder solution through logic-guided inquiries. This
software helps to solve design and project planning tasks more
quickly and efficiently. After having been guided through the
product selection, the user quickly and reliably gets the exact
technical date of the selected component as well as 2D and
3D CAD data in the correct file format for all common CAD
systems. This allows users to reduce costs while increasing
their competitiveness.
The ICS can be accessed at www.boschrexroth.com/ics.

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 3/44
Piston Area Areas Force at 500 psi 1) Flow at 4”/s 2)
Bore rod ratio Piston Rod Annulus Push Regen. Pull Out Regen. In
j A1 A
2 A 3 F 1 F 2 F 3 q V1 q V2 q V3
Ø in. Ø in. A1/A3 in.2 in.2 in.2 Lb. Lb. Lb. gpm gpm gpm
1.500 0.625 1.21 1.77 0.31 1.46 885 154 731 1.84 0.32 1.52
1.000 1.80 0.79 0.98 392 493 0.82 1.02
0.625 1.11 0.31 2.83 154 1,416 0.32 2.94
2.000 1.000 1.33 3.14 0.79 2.35 1,570 392 1,178 3.26 0.82 2.44
1.375 1.89 1.48 1.66 745 825 1.54 1.72
0.625 1.07 0.31 4.60 154 2,301 0.32 4.78
2.500 1.000 1.19 4.91 0.79 4.12 2,455 392 2,063 5.10 0.82 4.28
1.375 1.43 1.48 3.43 745 1,710 1.54 3.56
1.750 1.96 2.40 2.51 1,205 1,250 2.49 2.61
1.000 1.11 0.79 7.51 392 3,758 0.82 7.80
3.250 1.375 1.21 8.30 1.48 6.82 4,150 745 3,405 8.62 1.54 7.08
1.750 1.40 2.40 5.90 1,205 2,945 2.49 6.13
2.000 1.60 3.14 5.16 1,570 2,580 3.26 5.36
1.000 1.07 0.79 11.78 392 5,893 0.82 12.23
1.375 1.13 1.48 11.09 745 5,540 1.54 11.51
4.000 1.750 1.24 12.57 2.40 10.17 6,285 1,205 5,080 13.05 2.49 10.56
2.000 1.33 3.14 9.43 1,570 4,715 3.26 9.79
2.500 1.64 4.91 7.66 2,455 3,830 5.10 7.95
1.000 1.04 0.79 18.85 392 9,428 0.82 19.58
1.375 1.08 1.48 18.16 745 9,075 1.54 18.86
1.750 1.13 2.40 17.24 1,205 8,615 2.49 17.91
5.000 2.000 1.19 19.64 3.14 16.50 9,820 1,570 8,250 20.40 3.26 17.14
2.500 1.33 4.91 14.73 2,455 7,365 5.10 15.30
3.000 1.56 7.07 12.57 3,535 6,285 7.35 13.05
3.500 1.96 9.62 10.02 4,810 5,010 9.99 10.41
1.375 1.06 1.48 26.77 745 13,390 1.54 27.81
1.750 1.09 2.40 25.85 1,205 12,930 2.49 26.86
2.000 1.13 3.14 25.11 1,570 12,565 3.26 26.09
6.000 2.500 1.21 28.25 4.91 23.34 14,135 2,455 11,680 29.35 5.10 24.25
3.000 1.33 7.07 21.18 3,535 10,600 7.35 22.00
3.500 1.51 9.62 18.63 4,810 9,325 9.99 19.36
4.000 1.80 12.57 15.68 6,285 7,850 13.05 16.30
1.375 1.03 1.48 48.79 745 24,390 1.54 50.68
1.750 1.05 2.40 47.87 1,205 23,930 2.49 49.73
2.000 1.06 3.14 47.13 1,570 23,565 3.26 48.96
2.500 1.11 4.91 45.36 2,455 22,680 5.10 47.12
8.000 3.000 1.16 50.27 7.07 43.20 25,135 3,535 21,600 52.22 7.35 44.87
3.500 1.23 9.62 40.65 4,810 20,325 9.99 42.23
4.000 1.33 12.57 37.70 6,285 18,850 13.05 39.17
4.500 1.49 15.91 34.36 7,950 17,185 16.53 35.69
5.000 1.64 19.63 30.64 9,820 15,315 20.39 31.83
5.500 1.89 23.76 26.51 11,880 13,255 24.68 27.54
Note
1) Theoretical force
(efficiency not taken into account)
2) Stroke velocity
F1
F3qV3
A3A1F2A2
qV1 qV2
Stroke Tolerances
Stroke tolerances result from the cylinder head, cylinder base, cylinder tube, piston and piston rod. The stroke tolerance for all piston
diameters and stroke lengths is +1/16" / -0". Tighter stroke tolerances can be requested, however, details regarding the operating
pressure and operating temperature must be stated.
Stroke lengths Stroke tolerances
≤ 120" (refer to pg. 41 for buckling loads) +1/16" / -0"
Areas, Forces, Flows (dimensions in inches)

4/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
Ordering Details
Further details in clear text
Option 2
W = Without options
K = Thrust key
S = Stop tube (specify length)
Y = Additional piston rod ext.
state length in inches in clear text
X = Multiple or other selections,
specify in clear text
Option 1
W = Without options
E = Proximity switch, both ends 4)
A = Test point, both sides 5)
X = Multiple or other selections,
specify in clear text
Seal version
Suitable for mineral oil to
DIN 51 524 HL, HLP and HFA
M = Polyurethane seal system
T* = Servo quality/reduced friction
F* = BUNA-N seal system for HFC
Suitable for phosphate ester HFD-R
V* = Flourocarbon seal system
End position cushioning 6)
U = Without
D = Both sides, adjustable
S = Rod side, adjustable
K = Cap side, adjustable
Piston rod end 2)
H = Small male thread KK1
D = Intermediate male thread KK2
E = Female thread KK1
T = S.A.F.E., rod end
X = Special (specify)
Piston rod version
H = Case hardened and hard chromium plated 1)
S = 17-4 PH stainless steel
Port connection / location at cap
1 =
2 =
3 =
4 =
Port connection / location at head
1 =
2 =
3 =
4 =
Single rod cylinder = CD
Double rod cylinder = CG
Series = T1
Mounting types
Rectangular flange at head = MF1
Rectangular flange at cap = MF2
Square flange at head = MF5
Square flange at cap = MF6
Clevis mounting = MP1
Fixed pivot = MP3
Pivot Mount w/spherical bearing = MP5
Side lug = MS2
Centerline lugs mountings = MS3
Side tapped = MS4
End lugs = MS7
Trunnion at head = MT1
Trunnion at cap = MT2
Trunnion at intermediate position 3) = MT4
Basic version = MX0
Extended tie rods, both ends = MX1
Extended tie rods, at cap = MX2
Extended tie rods, at head = MX3
Bore Dia. Ø 1.50 to 8.00 inch
Piston rod Ø 0.63 to 5.50 inch
7) Stroke length in inches (ex. 12.00)
Design principle
Head and cap connected by tie rods = Z
Series
10 to 19 unchanged installation and connection dimensions = 1X
Port connections/ types
SAE straight thread port (ISO 11926-1) = S
NPT pipe tread port = U
Special (specify) = X
T1 Z 1X
Remarks:
1) Only 5/8" to 4" diameter piston rods are case hardened and hard
chrome plated. Above 4" diameter piston rods are chrome plated only.
2) With extreme shock loads the piston rod threads have to be selected,
taking the fatigue limits into account. Rod end clevis, installed parts,
etc. must always be firmly clamped against the piston rod shoulder.
3) State XV dimensions in inches in clear text.
4) Not available on 1-1/2"-2-1/2" bore size.
5) See page 34 for exceptions.
6) Fixed cushions on all 1-1/2" bore sizes both ends.
Fixed cushions on 2" bore / 1-3/8" rod, 2-1/2" bore / 1-3/4" rod and
3-1/4" bore / 2" rod sizes both ends
7) For cylinders with stop tube, the stroke in the model code is the effec-
tive stroke.
* Not recommended for load holding applications. Consult factory for
load holding options.
*
Viewed on piston rod
1
42
3
Viewed on piston rod
1
42
3

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 5/44
434
5
1. Double lip wiper
2. U-cup rod seal
3. Double acting piston seal
4. Wear bands
5. Piston threaded and sealed
to piston rod with permanent
adhesive and mechanically
secured with a set screw.
2
1
Sealing System
Exact-a-just™ cushioning
Cushioning System (optional) *
Patented Exact-a-just™ cushioning provides accurate micro-
meter adjustment
Exact-a-just™ cushioning permits adjustment over a wide range
of settings for faster cycle times
Results in reduced maintenance costs, reduced internal and
external shock, and softer cushioning stops
May be supplied at head, cap, or both ends
* Fixed cushions on all 1-1/2" bore sizes both ends.
Fixed cushions on 2" bore / 1-3/8" rod, 2-1/2" bore / 1-3/4" rod and
3-1/4" bore / 2" rod sizes both ends
Connection Port and Secured Air Bleed (standard)
ISO 11926-1 SAE straight thread (standard)
For other port options consult factory
To provide safety and prevent accidents, patented air bleed is
secured against unscrewing (standard on 2" - 8" bore sizes, not
available on 1-1/2" bore sizes)
Air bleed ports can become an alternate connection for a
pressure test fitting (optional) (not available on 1-1/2" bore sizes)
Also not available on head end of 2" bore / 1-3/8" rod and
2-1/2" bore / 1-3/4" rod sizes
Alternate pressure test fitting
"M" Polyurethane seal system (standard)
"T"* Seal system for low friction applications (available)
"F"* Standard seal system for HFC (water glycol) (available)
"V"* Seal system for (phosphate ester) (available)
* - not recommended for load holding applications.
Consult factory for load holding options
434
5
22
1
1. Double lip wiper
2. PTFE step seals
3. Low friction piston seal
4. Wear bands
5. Piston threaded and sealed
to piston rod with permanent
adhesive and mechanically
secured with a set screw.

6/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
MM B
Rod A +0.000 C D KK1 KK2 NA AC AD AE AF WG
Diameter -0.002
0.625 0.75 1.124 0.38 0.50 7/16 - 20 1/2 - 20 0.56 1.13 0.63 0.250 0.375 1.75
1.000 1.13 1.499 0.50 0.88 3/4 - 16 7/8 - 14 0.94 1.50 0.94 0.375 0.688 2.38
1.375 1.63 1.999 0.63 1.13 1 - 14 1-1/4 - 12 1.31 1.75 1.06 0.375 0.875 2.75
1.750 2.00 2.374 0.75 1.50 1-1/4 - 12 1-1/2 - 12 1.69 2.00 1.31 0.500 1.125 3.13
2.000 2.25 2.624 0.88 1.69 1-1/2 - 12 1-3/4 - 12 1.94 2.63 1.69 0.625 1.375 3.75
2.500 3.00 3.124 1.00 2.06 1-7/8 - 12 2-1/4 - 12 2.38 3.25 1.94 0.750 1.750 4.50
3.000 3.50 3.749 1.00 2.63 2-1/4 - 12 2-3/4 - 12 2.88 3.63 2.44 0.875 2.250 4.88
3.500 3.50 4.249 1.00 3.00 2-1/2 - 12 3-1/4 - 12 3.38 4.38 2.69 1.000 2.500 5.63
4.000 4.00 4.749 1.00 3.38 3 -12 3-3/4 - 12 3.88 4.50 2.69 1.000 3.000 5.75
4.500 4.50 5.249 1.00 SH1* 3-1/4 - 12 4-1/4 - 12 4.38 5.25 3.19 1.500 3.500 6.50
5.000 5.00 5.749 1.00 SH1* 3-1/2 - 12 4-3/4 - 12 4.88 5.38 3.19 1.500 3.875 6.63
5.500 5.50 6.249 1.00 SH1* 4 - 12 5-1/4 - 12 5.38 6.25 3.94 1.875 4.375 7.50
Piston Rod Versions
Piston Rod End
Rod Thread Options:
Standard KK1 Male furnished when not specified.
Male thread available in KK1 and KK2 thread sizes.
KK1 studded male rod end standard for 5/8", 1" & 1-3/8" rod dia.
Female thread available in KK1 thread size only.
Female Rod End
Option E
Male Rod End
Option H & D
S.A.F.E. Rod End
Option T
D (width across flats)
Note*: Spanner wrench holes: SH1 = 0.56" dia. For "F and V" dimensions, see respective mounting dimensions
shown on pages 8 thru 27.

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 7/44
Mounting Type Overview
MP5 (see Page 12, 13)
MF2 (see Page 8, 9)
MF1 (see Page 8, 9) MF5 (see Page 8, 9)
MF6 (see Page 8, 9) MP1 (see Page 10, 11)
MS2 (see Page 14, 15) MS3 (see Page 16, 17)
MS7 (see Page 16, 17) MT1 (see Page 18, 19)
MT2 (see Page 18, 19) MT4 (see Page 20, 21) MX0 (see Page 22, 23)
MX1 (see Page 24, 25) MX2 (see Page 24, 25) MX3 (see Page 24, 25)
MP3 (see Page 10, 11)
CGT1 (see Page 26, 27)
MS4 (see Page 14, 15)

8/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
EE
FB (NOMINAL BOLT DIAMETER)
G
ZJ + STROKE
P + STROKE
Y
V
ZB + STROKE
K
J
F
W
E
TF
UF
E
R
4
3
2
1
MM
LB + STROKE
EE
FB (NOMINAL BOLT DIAMETER)
ZF + STROKE
KF
G
ZJ + STROKE
P + STROKEY
V
LB + STROKE
J
F
W
E
TF
UF
E
R
4
3
2
1
MM
EE
TFUF
UF
TF
R
BOLT SIZE
FB
R
K
ZJ + STROKE
YP + STROKE
F
LB + STROKE
V
J
G
W
E4
3
2
1
E
MM
ZB + STROKE
EE
ZF + STROKE
F
TFUF
UF
TF
R
BOLT SIZE
FB
R
K
ZJ + STROKE
Y P + STROKE
F
LB + STROKE
V
J
G
W
E4
3
2
1
E
MM
Mounting MF1, MF2, MF5, MF6
CDT1 MF1
CDT1 MF2
CDT1 MF5
CDT1 MF6

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 9/44
Bore Ø SAE Port NPT Port
In. E EE EE F FB G J K R TF UF LB P
1.500 2.00 -6 3/8 0.38 0.31 1.50 1.00 0.25 1.43 2.75 3.38 4.00 2.25
2.000 2.50 -6 3/8 0.38 0.38 1.50 1.00 0.31 1.84 3.38 4.13 4.00 2.28
2.500 3.00 -6 3/8 0.38 0.38 1.50 1.00 0.31 2.19 3.88 4.63 4.13 2.28
3.250 3.75 -10 1/2 0.63 0.44 1.75 1.25 0.38 2.76 4.69 5.50 4.88 2.63
4.000 4.50 -10 1/2 0.63 0.44 1.75 1.25 0.38 3.32 5.44 6.25 4.88 2.69
5.000 5.50 -10 1/2 0.63 0.56 1.75 1.25 0.44 4.10 6.63 7.63 5.13 2.94
6.000 6.50 -12 3/4 0.75 0.56 2.00 1.50 0.44 4.88 7.63 8.63 5.75 3.13
Bore MM
In. Rod V W Y ZB ZF ZJ
1.500 0.625 0.25 0.63 1.94 4.88 5.00 4.63
1.000 0.50 1.00 2.31 5.25 5.38 5.00
2.000 0.625 0.25 0.63 1.94 4.94 5.00 4.63
1.000 0.50 1.00 2.31 5.31 5.38 5.00
1.375 0.63 1.25 2.56 5.56 5.63 5.25
2.500 0.625 0.25 0.63 1.94 5.06 5.31 4.75
1.000 0.50 1.00 2.31 5.44 5.50 5.13
1.375 0.63 1.25 2.56 5.69 5.75 5.38
1.750 0.75 1.50 2.81 5.94 6.00 5.63
3.250 1.000 0.25 0.75 2.38 6.00 6.25 5.63
1.375 0.38 1.00 2.63 6.25 6.50 5.88
1.750 0.50 1.25 2.88 6.50 6.75 6.13
2.000 0.50 1.38 3.00 6.63 6.88 6.25
4.000 1.000 0.25 0.75 2.38 6.00 6.25 5.63
1.375 0.38 1.00 2.63 6.25 6.50 5.88
1.750 0.50 1.25 2.88 6.50 6.75 6.13
2.000 0.50 1.38 3.00 6.63 6.88 6.25
2.500 0.63 1.63 3.25 6.88 7.13 6.50
5.000 1.000 0.25 0.75 2.38 6.31 6.50 5.88
1.375 0.38 1.00 2.63 6.56 6.75 6.13
1.750 0.50 1.25 2.88 6.81 7.00 6.38
2.000 0.50 1.38 3.00 6.94 7.13 6.50
2.500 0.63 1.63 3.25 7.19 7.38 6.75
3.000 0.63 1.63 3.25 7.19 7.38 6.75
3.500 0.63 1.63 3.25 7.19 7.38 6.75
6.000 1.375 0.25 0.88 2.78 7.06 7.38 6.63
1.750 0.38 1.13 3.03 7.31 7.63 6.88
2.000 0.38 1.25 3.16 7.44 7.75 7.00
2.500 0.50 1.50 3.41 7.69 8.00 7.25
3.000 0.50 1.50 3.41 7.69 8.00 7.25
3.500 0.50 1.50 3.41 7.69 8.00 7.25
4.000 0.50 1.50 3.41 7.69 8.00 7.25
Dimensions MF1, MF2, MF5, MF6
Table 1 - Dimensions affected by rod diameter
Table 2 - Dimensions not affected by rod diameter
Flange mounts are one of the stron-
gest, most rigid methods of mounting.
With this type of mount, there is little
allowance for misalignment, so when
long strokes are required, the free end
opposite the mounting should be sup-
ported to prevent sagging and possible
binding of the cylinder. Blind or cap
end mounts are best for thrust load ap-
plications, and rod or head end mounts
are best in tension applications. If an
application exceeds the rectangular
flange rating, a solid head or cap flange
mount is available.
When a less rigid mount can be used
and the cylinder can be attached to a
panel or bulkhead, an extended tie rod
mount could be considered.
Note: The bearing retainer plate is the
same as the “E” dimension for the 1.5”
– 6” bore sizes. Removable bearing
retainer is not available in the 1.5” – 6”
bore sizes.
Rod end options shown on page 6.

10/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
Mounting MP1, MP3
CDT1 MP1
CDT1 MP3
EE
MM
LR
MR
LB + STROKE
XC + STROKE
P + STROKE
J
ZJ + STROKE
ZC + STROKE
L
M
Ø CD
K
G
F
W
Y
V
E
EW
EE
MM
LR
MR
LB + STROKE
XC + STROKE
P + STROKE
J
ZJ + STROKE
ZC + STROKE
L
M
Ø CD
K
G
F
W
Y
V
E SQUARE
CW
CB
CW
3
42
1

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 11/44
CD
Bore EW/ +.000 SAE Port NPT Port
In. CB -.002 CW E EE EE F G J K L LR M MR LB P
1.500 0.75 0.501 0.50 2.00 -6 3/8 0.38 1.50 1.00 0.25 0.75 0.75 0.50 0.63 4.00 2.25
2.000 0.75 0.501 0.50 2.50 -6 3/8 0.38 1.50 1.00 0.31 0.75 0.75 0.50 0.63 4.00 2.25
2.500 0.75 0.501 0.50 3.00 -6 3/8 0.38 1.50 1.00 0.31 0.75 0.75 0.50 0.63 4.13 2.38
3.250 1.25 0.751 0.63 3.75 -10 1/2 0.63 1.75 1.25 0.38 1.25 1.00 0.75 0.94 4.88 2.63
4.000 1.25 0.751 0.63 4.50 -10 1/2 0.63 1.75 1.25 0.38 1.25 1.00 0.75 0.94 4.88 2.63
5.000 1.25 0.751 0.63 5.50 -10 1/2 0.63 1.75 1.25 0.44 1.25 1.00 0.75 0.94 5.13 2.94
6.000 1.50 1.001 0.75 6.50 -12 3/4 0.75 2.00 1.50 0.44 1.50 1.25 1.00 1.19 5.75 3.16
8.000 1.50 1.001 0.75 8.50 -12 3/4 0.75 2.00 1.50 0.56 1.50 1.25 1.00 1.19 5.88 3.25
Bore Ø Rod Ø
In. In. V W Y XC ZC ZJ XN
1.500 0.625 0.25 0.63 1.94 5.38 5.88 4.63 -
1.000 0.50 1.00 2.31 5.75 6.25 5.00 -
2.000 0.625 0.25 0.63 1.94 5.38 5.08 4.63 -
1.000 0.50 1.00 2.31 5.75 6.25 5.00 -
1.375 0.63 1.25 2.56 6.00 6.50 5.25 -
2.500 0.625 0.25 0.63 1.94 5.50 6.00 4.75 -
1.000 0.50 1.00 2.31 5.88 6.38 5.13 -
1.375 0.63 1.25 2.56 6.13 6.63 5.38 -
1.750 0.75 1.50 2.81 6.38 6.88 5.63 -
3.250 1.000 0.25 0.75 2.38 6.88 7.63 5.63 -
1.375 0.38 1.00 2.63 7.13 7.88 5.88 -
1.750 0.50 1.25 2.88 7.38 8.13 6.13 -
2.000 0.50 1.38 3.00 7.50 8.13 6.25 -
4.000 1.000 0.25 0.75 2.38 6.88 7.63 5.63 -
1.375 0.38 1.00 2.63 7.13 7.75 5.88 -
1.750 0.50 1.25 2.88 7.38 8.13 6.13 -
2.000 0.50 1.38 3.00 7.50 8.13 6.25 -
2.500 0.63 1.63 3.25 7.75 8.50 6.50 -
5.000 1.000 0.25 0.75 2.38 7.13 7.88 5.88 -
1.375 0.38 1.00 2.63 7.38 8.13 6.13 -
1.750 0.50 1.25 2.88 7.63 8.38 6.38 -
2.000 0.50 1.38 3.00 7.75 8.50 6.50 -
2.500 0.63 1.63 3.25 8.00 8.75 6.75 -
3.000 0.63 1.63 3.25 8.00 8.75 6.75 -
3.500 0.63 1.63 3.25 8.00 8.75 6.75 -
6.000 1.375 0.25 0.88 2.78 8.13 9.13 6.63 -
1.750 0.38 1.13 3.03 8.38 9.38 6.88 -
2.000 0.38 1.25 3.16 8.50 9.50 7.00 -
2.500 0.50 1.50 3.41 8.75 9.75 7.25 -
3.000 0.50 1.50 3.41 8.75 9.75 7.25 -
3.500 0.50 1.50 3.41 8.75 9.75 7.25 -
4.000 0.50 1.50 3.41 8.75 9.75 7.25 -
8.000 1.375 0.25 0.88 2.78 8.25 9.25 6.75 4.00
1.750 0.38 1.13 3.03 8.50 9.50 7.00 4.00
2.000 0.38 1.25 3.16 8.63 9.63 7.13 4.00
2.500 0.50 1.50 3.41 8.88 9.88 7.38 4.00
3.000 0.50 1.50 3.41 8.88 9.88 7.38 5.50
3.500 0.50 1.50 3.41 8.88 9.88 7.38 5.50
4.000 0.50 1.50 3.41 8.88 9.88 7.38 5.50
4.500 0.50 1.50 3.41 8.88 9.88 7.38 6.50
5.000 0.50 1.50 3.41 8.88 9.88 7.38 6.50
5.500 0.50 1.50 3.41 8.88 9.88 7.38 7.25
The Clevis or Pin mount-
ed cylinder is probably
the most widely used
of all mounts. For short
strokes, medium or
small cylinder applica-
tions, the clevis mounts
are recommended. If
this mount is applied
where stroke require-
ments cause the overall
length to be excessive,
the Cap Trunnion mount
can be used. Pivot
mounts must always be
used with a pivot type
rod end attachment.
The bearing retainer
plate is the same as the
“E” dimension for 1-
1/2”–6” bore sizes and
the “XN” dimension for
the 8” bore sizes. Rod
end options shown on
page 6.
MP1 mount includes
pivot pin. MP3 does not
include pivot pin.
Table 1 - Dimensions affected by rod diameter
Table 2 - Dimensions not affected by rod diameter
Dimensions MP1, MP3
MP3 not available in 8" bore.

12/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
Mounting MP5
CDT1 MP5
EE
ZH + STROKE
XH + STROKE
MA
+.0000
-.0006
Ø CD
MB
LA
LE
K
J
LB + STROKE
G
F
W
ZJ + STROKE
P + STROKE
Y
V
-.005
+.000
EX
EP
CX 2
4
E SQUARE
3
1
MM

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 13/44
Bore MM
In. Rod V W Y XH ZH ZJ
1.500 0.625 0.25 0.63 1.94 5.50 6.13 4.63
1.000 0.50 1.00 2.31 5.88 6.50 5.00
2.000 0.625 0.25 0.63 1.94 5.50 6.13 4.63
1.000 0.50 1.00 2.31 5.88 6.50 5.00
1.375 0.63 1.25 2.56 6.13 6.75 5.25
2.500 0.625 0.25 0.63 1.94 5.63 6.25 4.75
1.000 0.50 1.00 2.31 6.00 6.63 5.13
1.375 0.63 1.25 2.56 6.25 6.88 5.38
1.750 0.75 1.50 2.81 6.50 7.13 5.63
3.250 1.000 0.25 0.75 2.38 6.88 7.88 5.63
1.375 0.38 1.00 2.63 7.13 8.13 5.88
1.750 0.50 1.25 2.88 7.38 8.38 6.13
2.000 0.50 1.38 3.00 7.50 8.50 6.25
4.000 1.000 0.25 0.75 2.38 6.88 7.88 5.63
1.375 0.38 1.00 2.63 7.13 8.13 5.88
1.750 0.50 1.25 2.88 7.38 8.38 6.13
2.000 0.50 1.38 3.00 7.50 8.50 6.25
2.500 0.63 1.63 3.25 7.75 8.75 6.50
5.000 1.000 0.25 0.75 2.38 7.13 8.13 5.88
1.375 0.38 1.00 2.63 7.38 8.38 6.13
1.750 0.50 1.25 2.88 7.63 8.63 6.38
2.000 0.50 1.38 3.00 7.75 8.75 6.50
2.500 0.63 1.63 3.25 8.00 9.00 6.75
3.000 0.63 1.63 3.25 8.00 9.00 6.75
3.500 0.63 1.63 3.25 8.00 9.00 6.75
6.000 1.375 0.25 0.88 2.78 8.25 9.38 6.63
1.750 0.38 1.13 3.03 8.50 9.63 6.88
2.000 0.38 1.25 3.16 8.63 9.75 7.00
2.500 0.50 1.50 3.41 8.88 10.00 7.25
3.000 0.50 1.50 3.41 8.88 10.00 7.25
3.500 0.50 1.50 3.41 8.88 10.00 7.25
4.000 0.50 1.50 3.41 8.88 10.00 7.25
The MP5 (Universal) type mount is a pivot mount
with a spherical bearing fitted into the pivot
to permit 5 to 10 degrees of movement in a
plane perpendicular to the major plane of pivot
movement. It is probably the most serviceable
of the pivoted centerline mounts. For maximum
effectiveness, a spherical rod end fitting should
be utilized at the same time.
Rod end options shown on page 6.
Table 1 - Dimensions affected by rod diameter
Table 2 - Dimensions not affected by rod diameter
Dimensions MP5
Note: Only one (1) grease nipple is supplied up to 2.50” bore. On bore sizes 2.50” and larger, two (2) grease nipples will be
supplied, as shown.
Bore SAE NPT
In. E EE EE F G J K LB P CD CX EP EX LA LE MA MB
1.500 2.00 -6 3/8 0.38 1.50 1.00 0.25 4.00 2.28 0.50 0.88 0.38 0.44 0.88 0.75 0.75 0.75
2.000 2.50 -6 3/8 0.38 1.50 1.00 0.31 4.00 2.28 0.50 0.88 0.38 0.44 0.88 0.75 0.75 0.75
2.500 3.00 -6 3/8 0.38 1.50 1.00 0.31 4.13 2.38 0.50 0.88 0.38 0.44 0.88 0.75 0.75 0.75
3.250 3.75 -10 1/2 0.63 1.75 1.25 0.38 4.88 2.63 0.75 0.88 0.38 0.66 1.25 1.06 1.00 1.00
4.000 4.50 -10 1/2 0.63 1.75 1.25 0.38 4.88 2.63 0.75 1.25 0.56 0.66 1.25 1.06 1.00 1.25
5.000 5.50 -10 1/2 0.63 1.75 1.25 0.44 5.13 2.94 0.75 1.25 0.56 0.66 1.25 1.06 1.00 1.25
6.000 6.50 -12 3/4 0.75 2.00 1.50 0.44 5.75 3.13 1.00 1.62 0.75 0.88 1.62 1.44 1.25 1.50

14/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
The side or lug mounted cylinder provides a fairly rigid mount.
These type mounts can tolerate a slight amount of misalign-
ment when the cylinder is at full stroke, but as the piston
moves toward the blind end, the tolerance for misalignment
decreases. It is important to note that if the cylinder is used
properly, the mounting bolts are either in simple shear or ten-
sion without any compound stresses. An extended key plate
option is available to eliminate the need for fitted bolts or
external keys to carry the thrust load.
Note:
When specifying an MS2 mount with ports in the 2 or 4 quan-
drant, be sure to see that sufficient clearance between the port
fitting and the lug is available to insert a bolt or cap screw into
the lug.
Rod end options shown on page 6.
Mounting MS2, MS4
CDT1 MS2
CDT1 MS4
EE
NT (4 HOLES)
DT
2
E
SN + STROKE
XT
K
J
LB + STROKE
ZB + STROKE
G
F
W
ZJ + STROKE
P + STROKE
Y
V
TN
-.008
-.003
E SQUARE
2
1
4
3
MM
SBØ
EE
2
E
XS
WJ
SU SY
SS + STROKE
SUSY
ZJ + STROKE
-.008
-.003
ST
4 HOLES TS
SX
SW
US
E SQUARE
2
1
4
3
K
LB + STROKE
G
F
P + STROKE
Y
V
MM
ZB + STROKE

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 15/44
Bore MM
In. Rod V W Y XS XT ZB ZJ
1.500 0.625 0.25 0.63 1.94 1.38 1.94 4.88 4.63
1.000 0.50 1.00 2.31 1.75 2.31 5.25 5.00
2.000 0.625 0.25 0.63 1.94 1.38 1.94 4.94 4.63
1.000 0.50 1.00 2.31 1.75 2.31 5.31 5.00
1.375 0.63 1.25 2.56 2.00 2.56 5.56 5.25
2.500 0.625 0.25 0.63 1.94 1.38 1.94 5.06 4.75
1.000 0.50 1.00 2.31 1.75 2.31 5.44 5.13
1.375 0.63 1.25 2.56 2.00 2.56 5.69 5.38
1.750 0.75 1.50 2.81 2.25 2.81 5.94 5.63
3.250 1.000 0.25 0.75 2.38 1.88 2.44 6.00 5.63
1.375 0.38 1.00 2.63 2.13 2.69 6.25 5.88
1.750 0.50 1.25 2.88 2.38 2.94 6.50 6.13
2.000 0.50 1.38 3.00 2.50 3.06 6.63 6.25
4.000 1.000 0.25 0.75 2.38 1.88 2.44 6.00 5.63
1.375 0.38 1.00 2.63 2.13 2.69 6.25 5.88
1.750 0.50 1.25 2.88 2.38 2.94 6.50 6.13
2.000 0.50 1.38 3.00 2.50 3.06 6.63 6.25
2.500 0.63 1.63 3.25 2.75 3.31 6.88 6.50
5.000 1.000 0.25 0.75 2.38 2.06 2.44 6.31 5.88
1.375 0.38 1.00 2.63 2.31 2.69 6.56 6.13
1.750 0.50 1.25 2.88 2.56 2.94 6.81 6.38
2.000 0.50 1.38 3.00 2.69 3.06 6.94 6.50
2.500 0.63 1.63 3.25 2.94 3.31 7.19 6.75
3.000 0.63 1.63 3.25 2.94 3.31 7.19 6.75
3.500 0.63 1.63 3.25 2.94 3.31 7.19 6.75
6.000 1.375 0.25 0.88 2.78 2.31 2.81 7.06 6.63
1.750 0.38 1.13 3.03 2.56 3.06 7.31 6.88
2.000 0.38 1.25 3.16 2.69 3.19 7.44 7.00
2.500 0.50 1.50 3.41 2.94 3.44 7.69 7.25
3.000 0.50 1.50 3.41 2.94 3.44 7.69 7.25
3.500 0.50 1.50 3.41 2.94 3.44 7.69 7.25
4.000 0.50 1.50 3.41 2.94 3.44 7.69 7.25
8.000 1.375 0.25 0.88 2.78 2.31 2.81 7.31 6.75
1.750 0.38 1.13 3.03 2.56 3.06 7.56 7.00
2.000 0.38 1.25 3.16 2.69 3.19 7.69 7.13
2.500 0.50 1.50 3.41 2.94 3.44 7.94 7.38
3.000 0.50 1.50 3.41 2.94 3.44 7.94 7.38
3.500 0.50 1.50 3.41 2.94 3.44 7.94 7.38
4.000 0.50 1.50 3.41 2.94 3.44 7.94 7.38
4.500 0.50 1.50 3.41 2.94 3.44 7.94 7.38
5.000 0.50 1.50 3.41 2.94 3.44 7.94 7.38
5.500 0.50 1.50 3.41 2.94 3.44 7.94 7.38
Bore SAE NPT
In. E EE EE F G J K NT TN SB SN SS ST SU SW SX SY TS US LB P DT
1.500 2.00 -6 3/8 0.38 1.50 1.00 0.25 1/4 - 20 0.63 0.44 2.25 2.88 0.50 0.94 0.38 0.38 0.38 2.75 3.50 4.00 2.28 0.19
2.000 2.50 -6 3/8 0.38 1.50 1.00 0.31 5/16-18 0.88 0.44 2.25 2.88 0.50 0.94 0.38 0.38 0.38 3.25 4.00 4.00 2.28 0.34
2.500 3.00 -6 3/8 0.38 1.50 1.00 0.31 3/8 - 16 1.25 0.44 2.38 3.00 0.50 0.94 0.38 0.50 0.38 3.75 4.50 4.13 2.38 0.44
3.250 3.75 -10 1/2 0.63 1.75 1.25 0.38 1/2 - 13 1.50 0.56 2.63 3.25 0.75 1.25 0.50 0.50 0.50 4.75 5.75 4.88 2.69 0.50
4.000 4.50 -10 1/2 0.63 1.75 1.25 0.38 1/2 - 13 2.06 0.56 2.63 3.25 0.75 1.25 0.50 0.50 0.50 5.50 6.50 4.88 2.69 0.63
5.000 5.50 -10 1/2 0.63 1.75 1.25 0.44 5/8 - 11 2.69 0.81 2.88 3.13 1.00 1.56 0.69 0.69 0.69 6.88 8.25 5.13 2.94 0.75
6.000 6.50 -12 3/4 0.75 2.00 1.50 0.44 3/4 - 10 3.25 0.81 3.13 3.63 1.00 1.56 0.69 0.69 0.69 7.88 9.25 5.75 3.16 0.88
8.000 8.50 -12 3/4 0.75 2.00 1.50 0.56 3/4 - 10 4.50 0.81 3.25 3.75 1.00 1.56 0.69 0.88 0.69 9.88 11.25 5.88 3.28 1.13
Dimensions MS2, MS4
Table 2 - Dimensions not affected by rod diameter
Table 1 - Dimensions affected by rod diameter

16/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
Mounting MS3, MS7
CDT1 MS3
CDT1 MS7
The side or lug mounted cylinder provides a fairly rigid mount.
These type mounts can tolerate a slight amount of misalign-
ment when the cylinder is at full stroke, but as the piston
moves towards the blind end, the tolerance for misalignment
decreases. It is important to note that if the cylinder is used
properly, the mounting bolts are in simple shear or tension
without any compound stresses. An extended key plate option
is available to eliminate the ened for fitted bolts or external
keys to carry the thrust load (seep age 31)
When specifying an MS7 mount, carefully check the distance
between the rod and lug to determine if there is sufficient clear-
ance for the rod end attachment. It may be necessary to add a
plain rod extension to move the threaded rod end out beyond
the lug. The lugs serve as nuts on the bottom two tie rods,
therefore making it necessary to loosen the tie rods to remove
the rod bearing.
Rod end options shown on page 6.
SBØ
K
EE
SY
SY
4 HOLES
ST
G
SU
LB + STROKE
SS + STROKE
SU
J
P + STROKE
2
SW
SX
3
4
E
TS
US
1
E
XS
F
W
Y
ZJ + STROKE
ZB + STROKE
V
MM
E
3
4
2
E
1
G J EL EOEO
SE + STROKE
MM
ZE + STROKE
ZJ + STROKE
P + STROKE
XE + STROKE
Y
W
V
K
ET
LB + STROKE
FEL
E
2
R
ET
EE NPTF
4 PLACES

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 17/44
Bore SAE NPT
in. E EB EE EE EL EO ET F G J K R SB S SS ST SU SW SX SY TS US LB P SE
1.500 2.00 0.38 -6 3/8 0.75 0.25 0.53 0.38 1.50 1.00 0.25 1.43 0.44 5.50 2.88 0.50 0.94 0.38 0.31 0.31 2.75 3.50 4.00 2.28 5.50
2.000 2.50 0.38 -6 3/8 0.94 0.31 0.63 0.38 1.50 1.00 0.31 1.84 0.44 5.88 2.88 0.50 0.94 0.38 0.38 0.38 3.25 4.00 4.00 2.28 5.88
2.500 3.00 0.38 -6 3/8 1.06 0.31 0.78 0.38 1.50 1.00 0.31 2.19 0.44 6.25 3.00 0.50 0.94 0.38 0.50 0.38 3.75 4.50 4.13 2.38 6.25
3.250 3.75 0.50 -10 1/2 0.88 0.38 0.94 0.63 1.75 1.25 0.38 2.76 0.56 6.63 3.25 0.75 1.25 0.50 0.50 0.50 4.75 5.75 4.88 2.69 6.63
4.000 4.50 0.50 -10 1/2 1.00 0.38 1.16 0.63 1.75 1.25 0.38 3.32 0.56 6.88 3.25 0.75 1.25 0.50 0.50 0.50 5.50 6.50 4.88 2.69 6.88
5.000 5.50 0.50 -10 1/2 1.06 0.50 1.38 0.63 1.75 1.25 0.44 4.10 0.81 7.25 3.13 1.00 1.56 0.69 0.69 0.69 6.88 8.25 5.13 2.94 7.25
6.000 6.50 0.75 -12 3/4 1.00 0.50 1.59 0.75 2.00 1.50 0.44 4.88 0.81 7.75 3.63 1.00 1.56 0.69 0.69 0.69 7.88 9.25 5.75 3.16 7.75
8.000 8.50 0.69 -12 3/4 1.13 0.63 1.94 0.75 2.00 1.50 0.56 6.44 0.81 7.38 3.75 1.00 1.56 0.69 0.88 0.69 9.88 11.25 5.88 3.28 7.38
Bore MM
In. Rod V W Y XE XS ZB ZJ ZE
1.500 0.625 0.25 0.63 1.94 5.38 1.38 4.88 4.63 5.63
1.000 0.50 1.00 2.31 5.75 1.75 5.25 5.00 6.00
2.000 0.625 0.25 0.63 1.94 5.56 1.38 4.94 4.63 5.88
1.000 0.50 1.00 2.31 5.94 1.75 5.31 5.00 6.25
1.375 0.63 1.25 2.56 6.19 2.00 5.56 5.25 6.50
2.500 0.625 0.25 0.63 1.94 5.81 1.38 5.06 4.75 6.13
1.000 0.50 1.00 2.31 6.19 1.75 5.44 5.13 6.50
1.375 0.63 1.25 2.56 6.44 2.00 5.69 5.38 6.75
1.750 0.75 1.50 2.81 6.69 2.25 5.94 5.63 7.00
3.250 1.000 0.25 0.75 2.38 6.50 1.88 6.00 5.63 6.88
1.375 0.38 1.00 2.63 6.75 2.13 6.25 5.88 7.13
1.750 0.50 1.25 2.88 7.00 2.38 6.50 6.13 7.38
2.000 0.50 1.38 3.00 7.13 2.50 6.63 6.25 7.50
4.000 1.000 0.25 0.75 2.38 6.63 1.88 6.00 5.63 7.00
1.375 0.38 1.00 2.63 6.88 2.13 6.25 5.88 7.25
1.750 0.50 1.25 2.88 7.13 2.38 6.50 6.13 7.50
2.000 0.50 1.38 3.00 7.25 2.50 6.63 6.25 7.63
2.500 0.63 1.63 3.25 7.50 2.75 6.88 6.50 7.88
5.000 1.000 0.25 0.75 2.38 6.94 2.06 6.31 5.88 7.43
1.375 0.38 1.00 2.63 7.19 2.31 6.56 6.13 7.69
1.750 0.50 1.25 2.88 7.44 2.56 6.87 6.38 7.94
2.000 0.50 1.38 3.00 7.56 2.69 6.94 6.50 8.06
2.500 0.63 1.63 3.25 7.81 2.94 7.19 6.75 8.31
3.000 0.63 1.63 3.25 7.81 2.94 7.19 6.75 8.31
3.500 0.63 1.63 3.25 7.81 2.94 7.19 6.75 8.31
6.000 1.375 0.25 0.88 2.78 7.63 2.31 7.06 6.63 8.13
1.750 0.38 1.13 3.03 7.88 2.56 7.31 6.88 8.38
2.000 0.38 1.25 3.16 8.00 2.69 7.44 7.00 8.50
2.500 0.50 1.50 3.41 8.25 2.94 7.69 7.25 8.75
3.000 0.50 1.50 3.41 8.25 2.94 7.69 7.25 8.75
3.500 0.50 1.50 3.41 8.25 2.94 7.69 7.25 8.75
4.000 0.50 1.50 3.41 8.25 2.94 7.69 7.25 8.75
8.000 1.375 0.25 0.88 2.78 7.88 2.69 7.31 6.75 8.25
1.750 0.38 1.13 3.03 8.13 2.94 7.56 7.00 8.75
2.000 0.38 1.25 3.16 8.25 2.94 7.69 7.13 8.88
2.500 0.50 1.50 3.41 8.50 2.94 7.94 7.38 9.13
3.000 0.50 1.50 3.41 # 2.94 7.94 7.38 #
3.500 0.50 1.50 3.41 # 2.94 7.94 7.38 #
4.000 0.50 1.50 3.41 # 2.31 7.94 7.38 #
4.500 0.50 1.50 3.41 # 2.56 7.94 7.38 #
5.000 0.50 1.50 3.41 # 2.94 7.94 7.38 #
5.500 0.50 1.50 3.41 # 2.94 7.94 7.38 #
Dimensions MS3, MS7
Table 1 - Dimensions affected by rod diameter
Table 2 - Dimensions not affected by rod diameter
# = MS7 not available in this rod size

18/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
Mounting MT1, MT2
CDT1 MT1
CDT1 MT2
-.001
+.000
EE
V
XG
TL
ZJ + STROKE
P + STROKEY
LB + STROKE
Ø TD
K
J
G
F
W
UT
E SQUARE
4
3
2
1
MM
XN
-.001
+.000
EE
V
TL
ZJ + STROKE
P + STROKE
Y
XJ + STROKE
LB + STROKE
Ø TD
KJ
G
F
W
UT
E SQUARE
4
3
2
1
MM
XN

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 19/44
TD
Bore SAE Port NPT Port +.000
In. E EE EE F G J K -.001* TL UT UB P LB
1.500 2.00 -6 3/8 0.38 1.50 1.00 0.25 1.000 1.00 4.00 4.00 2.28 4.00
2.000 2.50 -6 3/8 0.38 1.50 1.00 0.31 1.000 1.00 4.50 4.00 2.28 4.00
2.500 3.00 -6 3/8 0.38 1.50 1.00 0.31 1.000 1.00 5.00 4.13 2.38 4.13
3.250 3.75 -10 1/2 0.63 1.75 1.25 0.38 1.000 1.00 5.75 4.88 2.69 4.88
4.000 4.50 -10 1/2 0.63 1.75 1.25 0.38 1.000 1.00 6.50 4.88 2.69 4.88
5.000 5.50 -10 1/2 0.63 1.75 1.25 0.44 1.000 1.00 7.50 5.13 2.94 5.13
6.000 6.50 -12 3/4 0.75 2.00 1.50 0.44 1.375 1.38 9.25 5.75 3.16 5.75
8.000 8.50 -12 3/4 0.75 2.00 1.50 0.56 1.375 1.38 11.25 5.88 3.28 5.88
Bore Rod
In. mm V W Y XG XJ XN ZJ
1.500 0.625 0.25 0.63 1.94 1.75 4.13 - 4.63
1.000 0.50 1.00 2.31 2.13 4.50 - 5.00
2.000 0.625 0.25 0.63 1.94 1.75 4.13 - 4.63
1.000 0.50 1.00 2.31 2.13 4.50 - 5.00
1.375 0.63 1.25 2.56 2.38 4.75 - 5.25
2.500 0.625 0.25 0.63 1.94 1.75 4.25 - 4.75
1.000 0.50 1.00 2.31 2.13 4.63 - 5.13
1.375 0.63 1.25 2.56 2.38 4.88 - 5.38
1.750 0.75 1.50 2.81 2.63 5.13 - 5.63
3.250 1.000 0.25 0.75 2.38 2.25 5.00 - 5.63
1.375 0.38 1.00 2.63 2.50 5.25 - 5.88
1.750 0.50 1.25 2.88 2.75 5.50 - 6.13
2.000 0.50 1.38 3.00 2.88 5.63 - 6.25
4.000 1.000 0.25 0.75 2.38 2.25 5.00 - 5.63
1.375 0.38 1.00 2.63 2.50 5.25 - 5.88
1.750 0.50 1.25 2.88 2.75 5.50 - 6.13
2.000 0.50 1.38 3.00 2.88 5.63 - 6.25
2.500 0.63 1.63 3.25 3.13 5.88 - 6.50
5.000 1.000 0.25 0.75 2.38 2.25 5.25 - 5.88
1.375 0.38 1.00 2.63 2.50 5.50 - 6.13
1.750 0.50 1.25 2.88 2.75 5.75 - 6.38
2.000 0.50 1.38 3.00 2.88 5.88 - 6.50
2.500 0.63 1.63 3.25 3.13 6.13 - 6.75
3.000 0.63 1.63 3.25 3.13 6.13 - 6.75
3.500 0.63 1.63 3.25 3.13 6.13 - 6.75
6.000 1.375 0.25 0.88 2.78 2.63 5.88 - 6.63
1.750 0.38 1.13 3.03 2.88 6.13 - 6.88
2.000 0.38 1.25 3.16 3.00 6.25 - 7.00
2.500 0.50 1.50 3.41 3.25 6.50 - 7.25
3.000 0.50 1.50 3.41 3.25 6.50 - 7.25
3.500 0.50 1.50 3.41 3.25 6.50 - 7.25
4.000 0.50 1.50 3.41 3.25 6.50 - 7.25
8.000 1.375 0.25 0.88 2.78 2.63 6.00 4.00 6.75
1.750 0.38 1.13 3.03 2.88 6.25 4.00 7.00
2.000 0.38 1.25 3.16 3.00 6.38 4.00 7.13
2.500 0.50 1.50 3.41 3.25 6.63 4.00 7.38
3.000 0.50 1.50 3.41 3.25 6.63 5.50 7.38
3.500 0.50 1.50 3.41 3.25 6.63 5.50 7.38
4.000 0.50 1.50 3.41 3.25 6.63 5.50 7.38
4.500 0.50 1.50 3.41 3.25 6.63 6.50 7.38
5.000 0.50 1.50 3.41 3.25 6.63 6.50 7.38
5.500 0.50 1.50 3.41 3.25 6.63 7.25 7.38
Dimensions MT1, MT2
Table 1 - Dimensions affected by rod diameter
All trunnion mount cylinders need a provision
on both ends for pivoting. These types of
cylinders are designed to carry shear loads and
the trunnion and pivot pins should be carried by
bearings that are rigidly held and closely fit for
the entire length of the pin.
Head or rod end trunnions should be carefully
applied to either short strokes or to applications
where the weight of the cylinder falls vertically
below the pin.
NOTE: The “XG” and “XJ” dimensions for MT1
and MT2 mounts are not NFPA Standard.
NOTE: The bearing retainer plate is the same
as the “E” dimension for the 1.5” – 6” bore
sizes and the “XN” dimension for the 8” bore
size.
Rod end options shown on page 6.
Table 2 - Dimensions not affected by rod diameter

20/44 Bosch Rexroth Corp. | Industrial Hydraulics CDT1/CGT1 | RA 17038/02.13
All trunnion mounted cylinders need a provision on both ends
for pivoting. These types of cylinders are designed to carry
shear loads and the trunnion and pivot pins should be carried
by bearings that are rigidly held and closely fit for the entire
length of the pin.
Specify “XV” dimension when ordering MT4 Intermediate Fixed
Trunnnion mounts. If not specified, trunnion will be located at
the center of the tube.
NOTE: The bearing retainer plate is the same as the “E” dimen-
sion for the 1.5” – 6” bore sizes and the “XN” dimension for the
8” bore size.
Rod end options shown on page 6.
Mounting MT4
CDT1 MT4
EE
BD
+.000
-.001
TD
UM
TM TL
UV
XV
K
ZJ + STROKE
YP + STROKE
F
LB + STROKE
V
J
G
W
E4
3
2
1
XN
MM
E