Bosch CameraPort CM-P 19 User manual

CameraPort CM-P 19
en Operating instructions
7 620 500 075

2| en
7 620 500 075 | 07.2020 Robert Bosch GmbH
Important information
Before using the device, please read these instructions
carefully and familiarize yourself with the device. Keep
these instructions in your vehicle for later reference.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user‘s
authority to operate the equipment.
Agreed product use
The device has been designed for operation in a
commercial vehicle with a 24 V electrical system.
The device must not be operated in any other environ-
ment or in an intended environment that is compromi-
sed e.g. by damage or malfunction.
CE approval
The CameraPort CM-P 19 has been tested according to
the regulatory requirements of the European Union (EU)
in accordance with the 2014/30/EU standard, and
meets all the requirements for the CE label.
The complete text of the EU Declaration of Conformity is
available at this internet address:
www.bosch-professional-systems.com
Specific to US:
The users manual or instruction manual for an intentio-
nal or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the
party responsible for compliance could void the user‘s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules [and
with RSS-GEN of Industry Canada].
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Changes or modifications made to this equipment not
expressly approved by Robert Bosch GmbH may void the
authorization to operate this equipment.
Responsible Party – U.S. Contact Information:
Robert Bosch LLC
15000 Haggerty Road
Plymouth, MI 48170
Contents | Important information
Contents
2 Important information
2 Agreed product use
2 CE approval
3 Installation notes
3 Switching on/off
3 Setup and configuration
3 Technical data
4 Device drawings

en | 3
7 620 500 075 | 07.2020Robert Bosch GmbH
en
Important information | Switching on/off | Setup and configuration | Technical data
Road safety
Make sure that your ability to drive is not
impaired and your vision is not blocked by the
device or the wiring connected to it.
Risk of electrical shock or fire
If you disassemble the device, it might result in
electrical shock or fire.
Do not open the device.
Malfunctions
Do not use the device if you notice any
malfunctions such as poor video quality.
Continued use of a malfunctioning system may
result in accidents, fire or electrical shock.
Installation notes
Risk of electrical short or fire
The installation of the device by a qualified
specialist workshop is strongly recommended.
Note:
Please also observe the information given in
the device drawings at the end of this docu-
ment.
Please observe the following installation notes:
fThe device must be installed in the coach interior.
fThe device must be mounted to a solid, even
surface.
fDo not exceed the maximum length of the device‘s
supply cables.
fThe device‘s supply cable must provide a minimum
cross sectional area of 1.5 mm2.
fObserve the minimum bending radius of the
device‘s supply cables.
fEnsure that the device‘s supply cables are pro-
tected against sharp edges.
fOnly use suitable screws and washers for mounting
the device.
Switching on/off
The device is automatically switched on or off by the
Coach Infotainment system of your Vehicle.
Setup and configuration
The CameraPort CM-P 19 requires individual setup and
configuration according to the layout of the Coach
Infotainment system in your vehicle.
Note:
Please refer to the system configuration
manual for the Coach Infotainment series for
information about setting up and configuring
the CameraPort CM-P 19.
Technical data
Power Supply 24 V (17 V – 36 V)
Current consumption
In operation 352 mA
Max. current < 1.5 A
Standby current < 0.1 mA
Inputs
4 x CVBS Analogue video | Auto sync
detection
Digital video Ethernet 100Base-TX | RJ 45 |
For IP camera
HDMI Version 1.4a | HDCP |
1920x1080x30
USB USB 2.0, type A | WMA, MP3,
AAC, MFi-IAP2, MTP
Output analogue video | CVBS | Split
screen (2 or 4 images in one
stream)
Operating temperature -20°C to +70 °C,
Storage temperature -40 °C to +85 °C
Dimensions (L x W x H) 212 x 119.6 x 43.1 mm
Weight Approx. 740 g
Certification CE, UN ECE R10
Subject to changes!

4| en
7 620 500 075 | 07.2020 Robert Bosch GmbH
Device drawings
Device drawings
The CameraPort CM-P 19 documentation consists of:
- 7620 500 075 Technical customer documentation (TCD)
- User Manual (this document)
- TCD drawing
Together, all documents form the complete product documentation. Please note
that all documented regulations and constrains have to be complied with when
installing this product into coaches.

en | 5
7 620 500 075 | 07.2020Robert Bosch GmbH
en
Device drawings
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc. in the United States and other countries.

Robert Bosch GmbH
Robert-Bosch-Platz 1
70839 Gerlingen
Germany
www.bosch-professional-systems.com
07/20 – CVO/PRM-CM