Bosch D9131A User manual

Parallel Printer Interface Module D9131A
User's Guide

D9131A
D9131A User's Guide
34584G Page 2 © 2002 Bosch Security Systems

D9131A
Overview
D9131A User's Guide
© 2002 Bosch Security Systems Page 3 34584G
1.0 Overview
1.1 Description
The printer installed with your security system records various types of events. You need a D9131A Parallel Printer
Interface Module to be able to use the printer. Your security system has been programmed by your security technician
to provide you with printed reports of activities such as Openings, Closings, Alarms, etc. This User’s Guide describes
the types of reports that can be printed, and explains the information contained in these reports. The manual that
comes with your printer explains printer functions such as how to load printer paper.
You can display events from your security system on a monitor; however, you will not retain a permanent record of
your system events this way.
1.2 Operation
The security system only remembers a certain number of events. If more than this number of events occur, new events
push out older events one by one. Your system has a Print Log command that allows you to print the entire history of
events stored in your system or you may select to print only events that have occurred from a specific date forward.
1.3 Printing Format
Your security system prints events with top and bottom margins and form feed between pages with descriptive headers.
Each event is printed on two lines. The first line contains the time and date the event occurred. The second line contains
the type of event and additional information.
EVENT ACCT AR ID PT# TEXT
01/01 01:21AM
Fire Alarm 1111 1 1 Hall Smoke
01/01 01:22AM
Fire Cancel 1111 1 002 1 John Smith
01/01 01:23AM
Fire Restoral 1111 1 1 Hall Smoke
Line 1:
•Date the event occurred at the panel
•Time the event occurred at the panel
Line 2:
•Event Description
Indicates the current armed status. The descriptions are listed alphabetically under Section 2.0 Event Descriptions and
Troubleshooting beginning on page 5.
•Account Number
•Area Number
•ID Number
USER XXX Event reported was initiated by this user ID.
USER XXX-0 Event reported was initiated with the Master User (Card/Token).
USER XXX-1,2,3 Event reported was initiated with the Sub User Noted (Card/Token).
•Point Number

D9131A
Overview
D9131A User's Guide
34584G Page 4 © 2002 Bosch Security Systems
•Text
Usually this is programmed by your alarm technician, however, the following text is not:
SDI XX- Event reported was initiated by the Serial Device Interface indicated. The numbers 1 through 8 indicate the
event is from one of the supervised command centers. The numbers 17, 18 or 19 indicate the event is from a printer.
Numbers 33 to 40 indicate the event is from the Access Control Module.
(The following text indicates previous armed status.)
Was Master Armed
Was Perim Delay
Was Perim Instant
Was Disarmed
Was Mstr Instnt
•User Text
Your alarm technician usually will program this. User text is printed whenever an event with a User ID is noted.

D9131A
Event Description and Troubleshooting
D9131A User's Guide
© 2002 Bosch Security Systems Page 5 34584G
2.0 Event Descriptions and Troubleshooting
The following events and their respective descriptions are listed in alphabetical order. Your system may not display all
of the events. For detail in the cause of events, see your Security System Owner’s Manual.
Event Description
Access Granted A card access holder has been granted access at the point specified.
AC Failure AC power to the security system is interrupted. Check the plug-in transformer and the
circuit breaker.
AC Restoral AC power to the security system has been restored.
ALARM-Door Open An access door has been held open beyond the allowed time while the area was armed.
Alarm Report Alarm at device in area specified. This event also reports Cross Point Alarms, including
Cross Group (CG:##) information.
All Points
Tested
All points have been tested while in the Service Walk Test, Fire Walk Test, or Walk Test
mode.
Bad Call To RAM System tried to call Remote Account To Ram Manager (RAM) and failed. Call your security
company.
Battery Low Security system battery is low. Replace the battery.
Battery Missing Security system battery is disconnected or has discharged. Reconnect the battery; call for
service.
Battery Restore Security system battery has recharged.
Cancel Alarm User with reported ID canceled an alarm from the area specified.
Card Assigned An access card/token was added to the system.
Command Bypass Device specified is bypassed.* System will not respond to faults at this point.
Closing Early User armed area earlier than expected.
Closing Late User armed area later than expected.
Closing Report User with reported ID armed area.
Comm Failure Security system could not communicate using the phone number reported. Call for service.
Date Changed User with reported ID changed the date in the security system.
Door Closed-
Restoral
An access door in the area specified restored to normal after a Door Left Open event
has occurred.
Door Cycled An access door in the area specified was cycled.
Door Left Open The door specified has been left open past the programmed time.
Door Locked An access door in the area specified was locked for normal operation.
Door Secured An access door in the area specified was secured, which prohibits access.
Door Unlocked An access door in the area specified was unlocked allowing free access.
Duress User with reported ID manually initiated a special alarm in the area specified.
Early to Open User disarmed area earlier than expected. If the entire security system is being disarmed,
the previous state of security system is indicated. If just one area is being disarmed, no
previous status is indicated.
Extra Point Area specified reports an unprogrammed device. Call for service.
Extn Close Time User with reported ID extended area’s closing time to that specified.
Fail To Close Area failed to arm within your programmed closing window.
Fail To Open Area failed to disarm within your programmed opening window.
F Close Early User with reported ID force armed* specified area later than expected.
F Close Late User with reported ID force armed* specified area later than expected.
F Close Pr Dlay User with reported ID force armed* perimeter with entry/exit delay.
F Close Pr Inst User with reported ID force armed* area perimeter with no delay time.
Fire Alarm Fire Alarm at device specified.
Fire Cancel See Cancel Alarm.
Fire Restoral The fire trouble or alarm event at the device specified has been restored.

D9131A
Event Description and Troubleshooting
D9131A User's Guide
34584G Page 6 © 2002 Bosch Security Systems
Event Description
Fire
Supervision
Supervision condition at the fire point specified.
Fire
Supervision
Restoral
Supervision condition at the fire point specified has been restored.
Fire Trouble Trouble condition at area device specified.
Fire Walk End Walk test* for fire devices in the area specified is complete.
Fire Walk Start A walk test* is in progress for fire devices in the area specified.
Forced Close User with reported ID armed area with point(s) faulted.
Forced Point User force armed device in area reported.
Late To Close User with reported ID armed the security system later than expected.
Late To Open User with the reported ID disarmed area later than expected. If the entire security system is
being disarmed, the previous state of the system is indicated. If just one area is being
disarmed, no previous state is indicated.
Log Overflow Security system event log is full. Events are being overwritten.
Log Threshold Security system event log is at the programmed maximum capacity.
Missing Alarm Device in area specified is not reporting. Call for service.
Missing Fire Fire device in area specified is not reporting. Call for service.
Missing Trouble Trouble Condition at area device specified.
Msng
Supervision
Supervision device at area specified is not reporting.
No Entry -
Level
An access card holder attempted access but was denied due to the user’s authority level.
No Entry -
Interlk
Access was denied due to the interlock door being open.
No Entry -
Secured
Access was denied due to the door being secured.
No Entry -
Unknown
Access was denied because the user was not found in the database.
Opening Report User with reported ID disarmed area.
Params Changed Security system programming has been changed.
Peri Dlay Armed User with ID reported armed the perimeter of the specified area with delay time.
Peri Inst Armed User with reported ID armed the perimeter of the specified area with no delay time.
Phone Line Fail The phone line specified is not working. Call for service.
Phone Restoral The problem with the phone line specified has been restored.
Point Bypass Area device specified is bypassed.* System will not respond to faults at this device.
Point Closing User armed device in area specified.
Point Opening User disarmed device in area specified.
Point Status Status report for device in area specified.
Point Tested This device has been walk tested.*
Prog Access Ok Account has been accessed locally by the device specified.
Pt Bus Trouble Wiring problem. Call for service.
Pt Bus Restoral Wiring problem is resolved.
Ram Access Fail Technician could not access your security system from the security company.
Ram Access Ok Your security company accessed your system from the security company.
Re-Boot Your security system was reset.
Relay Reset Relay has reset.
Relay Set Relay specified has been turned on.
Request To A Request To Enter device for an access door has been activated.

D9131A
Event Description and Troubleshooting
D9131A User's Guide
© 2002 Bosch Security Systems Page 7 34584G
Event Description
Enter
Request To Exit A Request To Exit device for an access door has been activated.
Restoral Report Restoral at point in area specified.
RF Low Battery A Low Battery condition at the point specified has been detected.
RF Batt Restor The Low Battery condition previously sent from the point specified has restored.
RTE Deny
Intrlok
A Request To Enter device has been activated but was denied due to the interlock door
being open.
RTE Deny
Secured
A Request To Enter device has been activated but was denied due to the door being
Secured. See Door Secured.
REX Deny
Intrlok
A Request To Exit device has been activated but was denied due to the interlock door being
open.
REX Deny
Secured
A Request To Exit device has been activated but was denied due to the door being Secured.
See Door Secured.
S: Alarm Status report: alarm at area specified.
S: Closing Status report: closing at area specified.
S: Fire
Supervision
Status report: Fire Supervision at area specified.
S: Opening Status report: opening at area specified.
S: Perim Delay Status report: area perimeter specified is armed with entry/exit delay.
S: Perim
Instant
Status report: area perimeter specified is armed (no delay).
S: Supervision Status report: Supervision at area specified.
S: Trouble Status report: trouble at area specified.
SDI Failure Serial Device Interface specified is not reporting. 1-8 = command centers; 017, 018, 019 =
printers; 33-40 = Access Control Module. 80 = Home Automation;
88 = RAMIV/Netcom. Make sure the device is plugged in.
SDI Restoral The problem with the device specified is resolved.
Sensor Reset User with reported ID reset detection devices in area specified.
Service End A Service Walk Test in the specified area has ended.
Service Start A Service Walk Test in the specified area has started.
Sked Bypass Sked* in area specified is bypassed.* System will not respond to faults at this device.
Sked Changed User with reported ID changed the Sked* indicated.
Sked Executed Sked* was activated.
Status report Status report was sent to the receiver.
Supervision Supervision condition at point specified.
Swinger Bypass Area specified had four alarm or trouble signals within an hour. It is now bypassed from the
system.
Test Report Test report was sent.
Time Changed User with reported ID changed the time in the security system.

D9131A
Event Description and Troubleshooting
© 2002 Bosch Security Systems 34584G
User's Guide
10/02
D9131A
Page 8 of 8
Event Description
Trouble Door
Open
Access door was left open beyond the programmed time.
Trouble Report Trouble condition at device specified.
Unverified
Event
The point specified generated an unverified alarm event.
User Alarm Cmd7 User with reported ID manually initiated special alarm in the area specified.
User Alarm Cmd9 User with reported ID manually initiated special alarm in the area specified.
Usr Code Change User ID specified was changed.
Usr Code Delete User ID specified was deleted.
User Level Set The authority level of the specified user has been modified.
User Tamper User with wrong ID tried to access specified area.
Walk End Walk test in area specified is complete.
Walk Start A walk test is in progress in the area specified.
Was Force Armed User with the reported ID force armed* account with point(s) faulted.
Watch Mode Start The Watch Mode in the specified area has started.
Watch Mode End The Watch Mode in the specified area has ended.
Watchdog Reset Panel was internally reset.
* For an explanation of terms, see your Security System Owner’s Manual.