Realtek Combo NGFF User manual

RTL8822C User’s Manual
(Realtek RTL8822C)
Combo NGFF Type1216 Module User’s Manual
Preliminary Version
2020/01/14
Realtek Semiconductor Corp.
No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Tel.: [phone]. Fax: [phone]
www.realtek.com

RTL8822C User’s Manual
CONTENT
ENVIRONMENTAL..........................................................................................................................3
OPERATING............................................................................................................................................3
STORAGE................................................................................................................................................3
MTBF CACULATION ..............................................................................................................................3
WARNING..........................................................................................................................................4
Federal Communication Commission Interference Statement ......................4
INDUSTRY CANADA STATEMENT ...........................................................................................................8
NCC 警語......................................................................................................8

RTL8822C User’s Manual
ENVIRONMENTAL
Operating
Operating Temperature: 0°C to +70 °C
Relative Humidity: 5-90% (non-condensing)
Storage
Temperature: -40°C to +80°C (non-operating)
Relevant Humidity: 5-95% (non-condensing)
MTBF caculation
Over 150,000hours

RTL8822C User’s Manual
Warning
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

RTL8822C User’s Manual
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
Radiation Exposure Statement: (Portable)
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
Radiation Exposure Statement: (Mobile)
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrators only. Per FCC KDB 996369
D03 OEM Manual v01 guidance, the following conditions must be strictly
followed when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
2.2 List of applicable FCC rules
This module has been tested for compliance to FCC Part 15
2.3 Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any
other usage conditions such as co-location with other transmitter(s) or being
used in a portable condition will need a separate reassessment through a
class II permissive change application or new certification.
2.4 Limited module procedures
Not applicable.
2.5 Trace antenna designs
Not applicable.
2.6 RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set

RTL8822C User’s Manual
forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20cm between the radiator &
your body. If the module is installed in a portable host, a separate SAR
evaluation is required to confirm compliance with relevant FCC portable
RF exposure rules.
2.7 Antennas
The following antennas have been certified for use with this module; antennas of the
same type with equal or lower gain may also be used with this module. The antenna
must be installed such that 20 cm can be maintained between the antenna and users.
Approved antenna(s) list :(Mobile)
Antenna
Set
Chain NO.
Brand
Model
Antenna
Gain
(dBi)
Frequency
range
(GHz)
Antenna
Type
Connector
Type
1
Chain 0
LYNwave
ALA110-222050-300011
3.5
2.4~2.5
PIFA
i-pex(MHF)
5
5.15~5.85
Chain 1
LYNwave
ALA110-222050-300011
3.5
2.4~2.5
PIFA
i-pex(MHF)
5
5.15~5.85
2
Chain 0
PSA
RFDPA171320EMLB301
3.14
2.4~2.5
Dipole
i-pex(MHF)
5
5.15~5.85
Chain 1
PSA
RFDPA171320EMLB301
3.14
2.4~2.5
Dipole
i-pex(MHF)
5
5.15~5.85
For SAR :(Portable)
Brand
Model
Antenna
Gain
(dBi)
Frequency
range
(GHz)
Antenna
Type
Connector
Type
REALTEK
RTK-ANT-0006
3.5
2.4~2.5
PIFA
i-pex(MHF)
5
5.15~5.85
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: TX2-RTL8822C”. The grantee's FCC ID can be used only
when all FCC compliance requirements are met.
2.9 Information on test modes and additional testing requirements

RTL8822C User’s Manual
This transmitter is tested in a standalone mobile RF exposure condition and
any co-located or simultaneous transmission with other transmitter(s) or
portable use will require a separate class II permissive change re-evaluation
or new certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does
not cover the FCC Part 15 Subpart B (unintentional radiator) rule
requirement applicable to the final host. The final host will still need to be
reassessed for compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the
Host and Module. The final product must be reassessed against all the
essential requirements of the FCC rule such as FCC Part 15 Subpart B before
it can be placed on the US market. This includes reassessing the transmitter
module for compliance with the Radio and EMF essential requirements of the
FCC rules. This module must not be incorporated into any other device or

RTL8822C User’s Manual
system without retesting for compliance as multi-radio and combined
equipment
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Radiation Exposure Statement: (Portable)
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power if such
function is available.
Déclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour
les Etats-Unis et le Canada établies pour un environnement non contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction
aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que
possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie
la plus faible si une telle fonction est disponible.
Radiation Exposure Statement: (Mobile)
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
greater than 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED

RTL8822C User’s Manual
établies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé àplus de 20 cm entre le radiateur et votre corps.

RTL8822C User’s Manual
This device is intended only for OEM integrators under the following conditions: (For
module device use)
1) The antenna must be installed and operated with greater than 20cm between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installé et exploité avec plus de 20 cm entre l'antenne et les
utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Tant que les 2conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization
is no longer considered valid and the IC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne
peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM
sera chargéde réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.

RTL8822C User’s Manual
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed and operated with greater than 20cm between the antenna and users. The
final end product must be labeled in a visible area with the following: “Contains IC:
6317A-RTL8822C”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où
l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les
utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription
suivante: "Contient des IC: 6317A-RTL8822C ".
End Product Labeling
The product can be kept as far as possible from the user body or set the device to
lower output power if such function is available. The final end product must be
labeled in a visible area with the following: “Contains IC:6317A-RTL8822C”.
Plaque signalétique du produit final
L'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le
dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est
disponible. Le produit final doit être étiqueté dans un endroit visible avec l'inscription
suivante: "Contient des IC: 6317A-RTL8822C ".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur

RTL8822C User’s Manual
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiquédans ce manuel.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies with
the e.i.r.p. limits as appropriate;
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s)
necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in
section 6.2.2.3 shall be clearly indicated.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions
précises sur les restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne
permis pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à
5 725 MHz doit être conforme à la limite de la p.i.r.e;
(iii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne
permis (pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être
conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
(iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de

RTL8822C User’s Manual
modèle de l’antenne et les pires angles d’inclinaison nécessaires pour rester conforme
à l’exigence de la p.i.r.e. applicable au masque d’élévation, énoncée à la
section 6.2.2.3, doivent être clairement indiqués
DETACHABLE ANTENNA USAGE
This radio transmitter (IC: 6317A-RTL8822C / Model: RTL8822C) has been
approved by ISED to operate with the antenna type listed below with maximum
permissible gain indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use
with this device.
Le présent émetteur radio (IC: 6317A-RTL8822C / Model: RTL8822C) a été
approuvé par ISED pour fonctionner avec les types d'antenne énumérés ci-dessous et
ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et
dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Approved antenna(s) list (Mobile)
Antenna
Set
Chain NO.
Brand
Model
Antenna
Gain
(dBi)
Frequency
range
(GHz)
Antenna
Type
Connector
Type
1
Chain 0
LYNwave
ALA110-222050-300011
3.5
2.4~2.5
PIFA
i-pex(MHF)
5
5.15~5.85
Chain 1
LYNwave
ALA110-222050-300011
3.5
2.4~2.5
PIFA
i-pex(MHF)
5
5.15~5.85
2
Chain 0
PSA
RFDPA171320EMLB301
3.14
2.4~2.5
Dipole
i-pex(MHF)
5
5.15~5.85
Chain 1
PSA
RFDPA171320EMLB301
3.14
2.4~2.5
Dipole
i-pex(MHF)
5
5.15~5.85

RTL8822C User’s Manual
For SAR (Portable)
Brand
Model
Antenna
Gain
(dBi)
Frequency
range
(GHz)
Antenna
Type
Connector
Type
REALTEK
RTK-ANT-0006
3.5
2.4~2.5
PIFA
i-pex(MHF)
5
5.15~5.85
PIFA
i-pex(MHF)
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商
號或使用者均不得擅自變更頻率、加大功率或變更原設計之
特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通
信；經發現有干擾現象時，應立即停用，並改善至無干擾時
方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波
輻射性電機設備之干擾。
1. 使用此產品時應避免影響附近雷達系統之操作。
2. 高增益指向性天線只得應用於固定式點對點系統。
模組認證：
1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤。

RTL8822C User’s Manual
2. 系統廠商應於平台上標示「本產品內含射頻模組：
XXXyyyLPDzzzz-x」字樣。
Japan Statement
Host system must be labeled with "Contains MIC ID:xxxxxx“, MIC ID displayed on
label.
Installing the Wireless PCIe NGFF1216 module
Hardware
Installing PCIe NGFF1216 module on NGFF2230 load board to PCIe NGFF2230
connector and connect two external Wi-Fi antennas on I-PEX connectors.

RTL8822C User’s Manual
Un-installing the Wireless PCIe NGFF1216 module
Hardware
Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF1216 module on
NGFF2230 load board and remove the Wireless PCIe NGFF1216 module on

RTL8822C User’s Manual
NGFF2230 board from PCIe NGFF2230 connector port
Installing the Wireless PCIe NGFF1216 module
Software
Before you proceed with the installation, please notice following descriptions.
Note1: The following installation was operated under Windows 7.
Note2: If you have installed the WLAN driver & utility before, please
uninstall the old version first.
A. Execute the “setup.exe”, Click “Next” to process the installation

RTL8822C User’s Manual
B. Click “Install” to process the installation
C. Click Install this driver software anyway

RTL8822C User’s Manual
D. After step “C”please press Next button.
E. Please click “YES” to install BT package.
F. Please click “下一步”to continue.

RTL8822C User’s Manual
G. Please click “下一步”to continue.