Bosch VJR-A3-IC User manual

AutoDome Junior
VJR-A3-IC
en Installation Manual

AutoDome Junior Table of Contents | en 3
Bosch Security Systems, Inc. Installation Manual F.01U.168.034 | 3.0 | 2010.12
Table of Contents
1 Installing a Recessed Mount 4
1.1 Description 4
1.1.1 Additional Requirements 4
1.1.2 Preparing the Ceiling for Installation 5
1.1.3 Installing the Camera to the Mounting Plate 8

4en | Installing a Recessed Mount AutoDome Junior
F.01U.168.034 | 3.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
1 Installing a Recessed Mount
1.1 Description
This chapter details how to recess mount the AutoDome Junior.
1.1.1 Additional Requirements
– Appropriate straight slot screwdrivers
– No. 2 Phillips screwdriver
– Appropriate tool for cutting a hole in drywall or ceiling tile
(if applicable)
– 4 in. x 4 in. junction box (optional)
– T-10 Torx wrench
– VJR-A3-SP, support kit for VJR-A3-IC mounting kit
NOTICE!
The image sensors in modern CCD cameras are highly sensitive
and require special care for proper performance and extended
lifetime. Follow the guidelines for optimum results with your
camera:
– Do not expose to direct sunlight or bright spotlights in
operating and nonoperating conditions.
– Avoid bright lights in the field of view of the camera. Bright
lights cause a “smearing” effect, which is visible as white
lines above and below the highlight. Prolonged exposure to
bright lights may cause bleaching of the sensor's color
filters. This will be visible as colored spots in the picture
and is irreversible.

AutoDome Junior Installing a Recessed Mount | en 5
Bosch Security Systems, Inc. Installation Manual F.01U.168.034 | 3.0 | 2010.12
1.1.2 Preparing the Ceiling for Installation
To mount to a recess mount, do the following:
1. Determine a secure location for the recessed mount
(supplied separately).
Figure 1.1 Recess Mount Dimensions
2. Drill or cut a 200 mm hole with a tolerance of 2.2 mm ( 7.9
in. ± 1/8).
3. Optional: if installing the AutoDome Junior HD to a
suspended ceiling tile or any other surface where
additional support is required, the VJR-A3-SP mounting kit
is recommended (supplied separately).
104.9
(4.13)
71.6
(2.82)
mm
(in.) 229.0
(9.02)

6en | Installing a Recessed Mount AutoDome Junior
F.01U.168.034 | 3.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
4. Align holes of mounting plate (supplied with dome) with
mounting bracket and attach with screws. Ensure that
both the crescent shape of the mounting plate and the
crescent shape of the mounting bracket are aligned.
Figure 1.2 Attach Mounting Plate to Mounting Bracket
5. Loosen the two clamp drive screws (item 5, above) so that
the clamping plates move freely.
6. Insert mount through the hole in the ceiling. Slide clamps
out and down so that the ceiling/drywall is captured in
between the clamps and the bracket flange. The ceiling/
drywall must have a maximum thickness of 41.7 mm
(1.64 in.) and an minimum thickness of 12.7 mm (0.50 in.).
1 Mounting Bracket
2 Mounting Plate
3 Clamping Plate
4 Crescent Shape
5 Clamp Drive Screw

AutoDome Junior Installing a Recessed Mount | en 7
Bosch Security Systems, Inc. Installation Manual F.01U.168.034 | 3.0 | 2010.12
Figure 1.3 Attach Recess Mount to Ceiling
7. Tighten both clamps using the clamp drive screws
(installed on the assembly) and a #2 Phillips screwdriver.
NOTICE!
Over-torquing the ceiling clamps can damage the clamp or
ceiling. Only tighten the clamp until it contacts the ceiling and
you start to feel some resistance. If using a power screwdriver,
set the torque level to the lowest setting.
NOTICE!
If you need to install the the VJR-A3-SP Support Bracket, refer
to the guide included with the bracket. Once the bracket is
installed, continue with the next section.

8en | Installing a Recessed Mount AutoDome Junior
F.01U.168.034 | 3.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
1.1.3 Installing the Camera to the Mounting Plate
To install the base to a surface or suspended ceiling using the
supplied mounting plate, do the following:
1. Loosen the single safety locking screw on the base of the
unit using the user-supplied T-10 Torx wrench.
Figure 1.4 Unlock Safety Locking Screw
2. Remove the screw from the Earth ground ( )on the top
of the mounting bracket.
3. Attach a user-supplied ground wire to the Earth ground
( ) screw hole on the mounting bracket and secure with
the screw.
4. Attach the green grounding wire from the unit to the
grounded ( ) screw hole on the mounting bracket using
the attached captive screw washer.
5. Route wires on the side of mounting plate with the
crescent shaped cut-out.
6. Connect the mating connectors (supplied in the accessory
kit) with the flying leads to the user supplied wiring.
CAUTION!
All wires for installation applications must be routed through a
grounded conduit.

AutoDome Junior Installing a Recessed Mount | en 9
Bosch Security Systems, Inc. Installation Manual F.01U.168.034 | 3.0 | 2010.12
7. Plug the matching connectors from the camera into the
mating connectors from the ceiling.
Figure 1.5 Match Connectors
1 Locking Screw
2 Crescent Shape
3 Mounting Plate
4 Vertical Tab

10 en | Installing a Recessed Mount AutoDome Junior
F.01U.168.034 | 3.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
8. Attach the camera to the mounting plate by inserting the
vertical tab on the plate (item 1, below) into the recessed
slot on the top of the camera dome (Item 3) to the right of
the safety locking screw (item 2).
Note: Do not loosen the three brass buttons (item 4).
These brass buttons engage the slotted tabs (item 5) on
the mounting plate.
Figure 1.6 Tab/Slot Alignment Detail
1 Vertical Tab (on mounting plate)
2 Locking Screw
3 Recessed Slot (on dome housing)
4 Brass Button (total of three on housing)
5 Slotted Tab (total of three on mounting plate)