Boss Design Apollo User manual

Apollo Table Assembly Instructions
Step 1
Step 1Step 1
Step 1
Insert cable management strip (CM002-0620) into the slot in the e truded cast leg (LE102)
Step
Step Step
Step 2
22
2
Insert foot insert (FT102B) into the bottom of the leg
Note - ensure that the tapped hole is at the base of the leg
Cable Management Strip
(CM002-0620)
Extruded
Leg
(LE102)
Foot Insert
(F 102B)
tapped h
ole

Step
Step Step
Step 3
33
3
Screw adjusting screw (FT103) into the threaded hole in the base of the Leg
Step 4
Step 4Step 4
Step 4
Insert fi ing block (FI505) into the slot in the top of the leg
Note - ensure that the tapped hole is on the lower half of the fi ing block
Adjusting Screw
(F 103)
Fixing
block
(FI505)
tapped h
ole
to
be nearer
bottom edge

Step 5
Step 5Step 5
Step 5
Fi bracket (FI501) to leg using M8 30 button head screw (SC312A)
Note - ensure that the top surface of the bracket and the leg are aligned before tightening the
screw completely
Step 6
Step 6Step 6
Step 6
Fi corner brace (FI502) to the top of all three corner legs using three M6 20 countersunk
socket head screws (SC012A)
bracket
(FI501)
M8 x 30 button
head screw
(SC312A)
(FI505
)
Corner Brace
(FI502)
M6 x 20 Countersunk Socket Head Screws
(SC012A)

Step 7
Step 7Step 7
Step 7
For tables with mid legs assemble cable management strip (CM002-0620), foot insert (FT102B)
and adjusting screw (FT103) to mid position e truded leg (LE103) as per steps 1 to 3 (above).
Secure straight brace (FI504) to top of leg using M10 25 countersunk socket head screw
(SC313A)
Step
Step Step
Step 8
88
8
Insert cable management (CM002) into all support rails (SR001).
Note - the length of the cable management strip should be appro imately 115mm shorter than
the overall length of the support rail into which it is inserted.
M10 x 25 countersunk socket head screw
(SC313A)
straight brace
(FI504)
mid position
extruded leg
(LE103
)
Support Rail
(SR001)
Cable Management
(CM002)

Step 9
Step 9 Step 9
Step 9 (only on tables with more than four legs)
Insert fi ing block (FI505) into the end of the support rail (SR001, 002, or 003) after inserting the
cable management rail.
Note - it may be necessary to cut the cable management strip shorter to allow this
Step 10
Step 10 Step 10
Step 10 (only on tables with more than four legs)
Secure cross brace bracket (FI518 or FI519) to fi ing block (FI505) using M6 25 flanged button
head screw (SC311A) - D
DD
DO NOT FULLY TIGHTEN
O NOT FULLY TIGHTENO NOT FULLY TIGHTEN
O NOT FULLY TIGHTEN
Fixing Block
(FI505)
Cross Brace Bracket
(FI518 or FI519)
M6 x 25 Flanged
Button Head Screw
(SC311A)

Step 11
Step 11 Step 11
Step 11 (only on tables with more than four legs)
Slide cross brace (SR006) to cross brace bracket (FI518 or FI519)
Step 12
Step 12 Step 12
Step 12 (only on tables with more than four legs)
Secure cross brace (SR006) with a M6 16 countersunk socket head screw (SC090A), set top of
cross brace and support rail level and then tighten M6 25 flanged button head screw (as per
step 7)
Cross Brace
(SR006)
M6 x 16 Countersunk Socket Head Screw
(SC090A)

Step 13
Step 13Step 13
Step 13
Slide support rail onto braces on each leg
Note - refer to individual table drawings for plan of rails.
Step 14
Step 14Step 14
Step 14
Fi support rail to brace using three M6 16 countersunk socket head screws (SC090A) at each
end of rail
M6 x 16 Countersunk
Socket Head Screws
(SC090A
)

Step
Step Step
Step 15
1515
15
Fi table top to fully assembled frame using M6 16 flanged socket button head screw
(SC304A)
M6 x 16mm Flanged Socket
Button Head Screw
(SC304A
)