BOSSCO BRRF40 User manual
THIS PACKAGE CONTAINS
1 - BRRF40 Overhead Speaker System
1 - Bluetooth Multi-Function Controller Kit
2 - 1.75” / 2.00” Rollbar Cage Mounting Kit
1 - Quick Connect Power Cable
1 - User Manual Quick Start Guide / Poster
1 - Warranty Card / Facebook Card
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by
user. This equipment complies with FCC/ IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator at least 20 cm or more away from
person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration
RUPRGL¿FDWLRQVFDUULHGRXWZLWKRXWDSSURSULDWHDXWKRUL]DWLRQPD\LQYDOLGDWHWKH
user’s right to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
GHWHUPLQHGE\WXUQLQJWKHHTXLSPHQWRႇDQGRQWKHXVHULVHQFRXUDJHGWRWU\WR
correct the interference by one or more of the following measures:
Ƒ5HORFDWHRUUHRULHQWWKHUHFHLYLQJDQWHQQD
Ƒ,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU
Ƒ&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWGLႇHUHQWIURPWKDWWRZKLFKWKH
receiver is connected.
Ƒ&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS
USERMANUAL
QUICKSTART GUIDE
Thank you for purchasing this
BRRF40 Soundbar Sound System
Please read through these instructions carefully so you will know
how to operate your model properly.
$IWHU\RXKDYHÀQLVKHGUHDGLQJWKHLQVWUXFWLRQVNHHSWKLVGRFXPHQW
in a safe place for future reference.
INFORMATION TO THE USER
INFORMATION TO THE USER
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks is under license.
Other trademarks and trade names are those of their respective owners.
CAUTION!!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
GETTING TO KNOW YOUR
BRRF40 MULTIFUNCTION CONTROLLER (MFC)
BEFORE YOU START
IMPORTANT SAFETY PRECAUTIONS
Ŷ'RQRWRSHUDWHPRELOHHTXLSPHQWZKLOHGULYLQJDPRWRUL]HGYHKLFOH±VDIHGULYLQJDQG
safety consideration of others should always be your highest priority
ŶIn the event you should notice smoke, strange noises or odor from this product, or any
RWKHUDEQRUPDOVLJQVLPPHGLDWHO\WXUQRႇWKHSRZHUDQGFRQVXOW\RXUGHDOHURUWKHQHDUHVW
DXWKRUL]HGBOSS AUDIO Service Center. Using this product in this condition may result in
permanent damage to the system
ŶSet your volume control at a low setting, then slowly increase the sound until you can
hear it comfortably without distortion, or ear discomfort
ŶBE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
- Do not turn up the volume so high that you can’t hear what’s around you
8VHFDXWLRQRUWHPSRUDULO\GLVFRQWLQXHXVHLQSRWHQWLDOO\KD]DUGRXVVLWXDWLRQV
INSTALLATION PRECAUTIONS
WARNING - Always consult a professional installer
ŶDo not attempt to install or service this product by yourself. Installation or servicing of this
product by persons without professional training and experience in electronic equipment
DQGPRWRUL]HGYHKLFOHDFFHVVRULHVPD\EHGDQJHURXVDQGFRXOGH[SRVH\RXWRWKHULVNRI
HOHFWULFVKRFNLQMXU\RURWKHUKD]DUGV
Ŷ5HIHUDQ\UHSDLUVWRDTXDOL¿HGBOSS AUDIO SYSTEMS Service Center
ŶThe BRRF40 should be hard wired directly to the main vehicle battery
ŶWhen wiring directly to the vehicles battery, be sure to disconnect the batteries negative
terminal wire before starting any wiring procedures
ŶThe ground cable length should be short as possible (See wiring diagram)
ŶThe BRRF40 has a weather resistant design, it should not be under any circumstances
be submerged in, or under water
ŶUse only the supplied installation parts provided with the BRRF40
ŶWash with a mild detergent and lukewarm water using a clean sponge or a soft cloth
ŶRinse well with clean water
“DO NOT’S” - Very Important
ŶDON’T clean in hot sun or on very hot days
ŶDON’T use abrasive or highly alkaline cleaners on the main body
Ŷ'21¶7VFUDSHWKHPDLQERG\ZLWKUD]RUEODGHVRURWKHUVKDUSLQVWUXPHQWV
ŶDON’T ever use, gasoline, acetone or carbon tetrachloride
ŶDON’T ever use a pressure washer aimed at the speakers
GETTING STARTED
A
1
2
3
4
5
6
7
8
9
MFC - MULTIFUNCTION CONTROLLER
DOME LIGHT ON/OFF - (Auto 10 minute timer when MFC ACC is turned OFF)
POWER ON - Press and hold for 3 seconds
EQ - EQ1 | EQ2 | EQ3 | FLAT - EQ1 Default Press and hold for 3 seconds
NEXT TRACK - FF press and hold
PLAY/PAUSE - AUX MUTE
BLUETOOTH PAIRING INDICATOR LED - BLUE / AUX RED COLOR
PREVIOUS TRACK - FR press and hold
VOLUME DOWN - Ramp DOWN press and hold
VOLUME UP - Ramp UP press and hold
CAUTION!! Using other mounting methods may void this warranty
PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION
1) Power on the MFC by long-pressing the 3Power button for 3 seconds, long-press the
6Bluetooth button for 3 seconds, the BLUE LEDZLOOVWDUWWRUDSLGO\ÀDVKVLJQDOOLQJWKDW
the MFC is now ready for Bluetooth pairing
NOTE: You have 2 minutes before you must restart this procedure over again.
2) The MFC is now in pairing mode:
ANDROID users:
a. Go into the Settings Menu of your device
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth and press SCAN
d. “BOSS REBEL UTV” will now be displayed under AVAILABLE DEVICES
e. If prompted, enter passcode: “0000”
iOS users:
a. Go into the Settings Menu of your iOS device
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth
d. “BOSS REBEL UTV” will now be displayed
e. If prompted, enter passcode: “0000”
3) If BOSS REBEL UTV is not seen, repeat the above steps to refresh the “Device List”
4) When the connection is successful a tone will be heard, and the Bluetooth LED indicator
will light solid, you are now ready to stream music from your favorite media player to the MFC
Using this product without running the engine can drain the battery.
To avoid battery exhaustion, be sure to occasionally run the
vehicles engine while using this product.
BLUETOOTH OPERATION STREAMING MUSIC
RECONNECTION
1) Power on the MFC and your last paired device Bluetooth.
2) Ensure you are within range of the MFC, the unit will now automatically reconnect
3) If the device is out of range from the MFC, it will disconnect automatically:
a. The MFC will reconnect automatically to your device when in range
4) If your device was previously paired with the MFC, but it wasn’t the last paired device:
a. Ensure no other devices are currently paired
b. Enter the Bluetooth Menu on your device being paired
c. “BOSS REBEL UTV” will display under AVAILABLE DEVICES
d. Choose the “BOSS REBEL UTV” to reconnect
5) To clear all previously paired devices from memory, press and hold the MFC Bluetooth
button for 10 seconds
NOTE: Some devices may require a manual Bluetooth reconnection once the devices
Bluetooth is powered OFF / ON and/or back in range, repress the BOSS REBEL UTV
button in BLUETOOTH settings on your device
3
Tips:
MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION
1) Press the 5PLAY/PAUSE once to start playing music or press the PLAY button from
your devices touch screen
2) To skip songs or advance, press the 4NEXT TRACK button
3) To select the previous song, press the 7PREVIOUS TRACK button
VOLUME CONTROL
4) To raise the volume press the 9VOLUME UP button or use your devices controls
5) To lower the volume press the 8VOLUME DOWN button or use your devices controls
NOTE: If BLUETOOTH or AUX is disconnected for more than 10 minutes the MFC will
automatically turn OFF, however, when not in use the ACC switch should be manually
turned OFF to keep the vehicles main battery from draining
MULTIFUNCTION CONTROLLER AUX-IN OPERATION
1) Power on the MFC by pressing and holding down the 3POWER button for 3 seconds
2) Disconnect any paired BluetoothGHYLFHE\WXUQLQJRႇ Bluetooth in your devices
Settings Menu
3) Connect your 3.5mm AUX-IN cable located on front side of the MFC to your devices
headphone jack
4) Route the wire back to MFC, secure your device in a safe location
VOLUME CONTROL
5) To raise the volume press the 9VOLUME UP button
6) To lower the volume press the 8VOLUME DOWN button
7) To MUTE the volume press the 5PLAY/PAUSE button
AUX-INPUT
Make sure your device Bluetooth volume is set at 100% level
before stowing your device
BEFORE YOU START INSTALLATION
Make sure your device headphone volume is set at 100% level
before stowing your device
MFC can play audio from
any device that has a 3.5mm
headphone audio jack.
INSERT
(Cable not included)
YOUR
DEVICE
Tips:
Tips:
MULTI-FUNCTION CONTROLLER MOUNTING
TOOLS NEEDED:
- Crimp Tool
- Wrench or Pliers
- 3mm Allen Wrench
MOUNTING THE OVERHEAD SOUNDBAR
:KHQUHSODFLQJWKHIXVHEHVXUHWRRQO\XVHDIXVHRIWKHUDWLQJVSHFL¿HGRQ
this product. To avoid short-circuiting, cover any disconnected leads with insulating
tape. It is especially important to insulate any unused wires, which if left uncovered
may cause a short circuit. When connecting other devices to this product, refer to
the manual for the product to be connected. The black cable is ground, make sure
WRFRQQHFWWKHJURXQGZLUH¿UVW(QVXUHWKDWWKHJURXQGZLUHLVSURSHUO\FRQQHFWHG
to metal parts of the vehicles body frame or direct to the battery if your vehicle
does not have a grounded chassis frame The ground wire of this units power amp
and a second powered system must be connected to the frame separately with
GLႇHUHQWVFUHZV,IWKHVFUHZIRUWKHJURXQGZLUHORRVHQVRUIDOOVRXWLWFRXOGUHVXOW
LQ¿UHRUPDOIXQFWLRQ
To avoid potential shorts in the electrical
V\VWHPEHVXUHWRGLVFRQQHFWWKH±
battery cable before installation. Use this
XQLWZLWKD9ROWEDWWHU\DQGQHJDWLYH
grounding only. Failure to do so may result
LQD¿UHRUPDOIXQFWLRQ
BRRF40
REFLEX SERIES
BLUETOOTH®| 40” SIDE x SIDE | AMPLIFIED OVERHEAD SYSTEM
USER’S MANUAL
QUICK START GUIDE
BRRF40
USER’S MANUAL
REFLEX SERIES
40” SIDE x SIDE | AMPLIFIED OVERHEAD SOUND SYSTEM
WITH BLUETOOTH REMOTE CONTROLLER
PRINTED IN CHINA
VER:1.1 EN
iPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other countries
Android is a trademarks of Google Inc. registered in the U.S. and other countries.
%266$XGLR6\VWHPVLVQRWDႈOLDWHGZLWK$SSOH,QFRU*RRJOH,QF
317
BOSS Audio Systems
/XQDU&RXUW2[QDUG&$
www.bossaudio.com_
Tech Support: www.bossaudio.com/support/technical-support
BLUETOOTH
9HUVLRQ
$'3$95&3*$77
5DQJHIWP&ODVV
%DQG'633UHVHW(4
5&$/LQH2XWSXW9506
SPEAKERS
'LPHQVLRQ´0,'´68%
0,'&RQH7\SH33&DUERQ
7ZHHWHU6L]H´7LWDQLXP
AMPLIFIER
0D[LPXP2XWSXW3RZHU:DWWV
,QSXW,PSHGDQFHNȍ
)UHTXHQF\5HVSRQVH+]N+]
GENERAL
2SHUDWLRQDO3RZHU9'&9DOORZDEOH
0$;&XUUHQW'UDZ$
86%&KDUJLQJ$#9'&
5HSODFHPHQW)XVH$$727<3(
&DELQHW0DWHULDO+LJK,PSDFW$%6
SPECIFICATIONS
WIRE DIAGRAM
10.33"
(262.5mm)
10.33"
(262.5mm)
40.7"
(1034mm)
4.09"
(104mm)
Dimensions:
40.7"(1034mm) x 4.09" (104mm) x 10.33" (262.5mm)
Weight:
25.3lbs (11.5 kg)
15A
Fuse and fuse holder
Chassis
ground
point
BATTERY
Replace with 15A only
INSERT
DIRECT BATTERYWIRING CIRCUIT
RED
BLACK
Chassis
ground
point
MFC
Ground wire
Metal frame
(AUX Cable not included)
INSERT
RED
BLACK
ACC SWITCH
LINE OUT
(-) ORANGE
(+) BLUE
DOME LIGHT
AMP REMOTE INPUT
RIGHT
LEFT
GROUND CRIMP
DAISY CHAIN
LINE OUTPUTS
LINE IN
(-) MOMENTARYTO ACTIVATE
3A
&RORU%ODFN
:HLJKWOEVNJ
'LPHQVLRQV,QFKHV:[+['[[
'LPHQVLRQVFP:[+['[[
6WRUDJH7HPSHUDWXUHoFto 175oF / -15o&WRoC
2SHUDWLRQ7HPSHUDWXUHoFto 140oF / 0oC to 60oC
SPECIFICATIONS SUBJECT TOCHANGE WITHOUT NOTICE
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including
photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO Inc.
Copyright © 2017 BOSS AUDIO Inc.
BLUETOOTH OPERATION
CAUTION!!
Mounting brackets should be periodically checked to be sure they are tight
and secure before use of the vehicle.
CABLE NOT INCLUDED
40
6
7
4
5
8
9
5
8
9
3
1) Determine the best location on your rollbar for your vehicle, install rubber
bushings on the rollbar, ensure there is ample head space
2) Apply supplied Loc-Tight to allen bolt tips, let dry for 20 minutes
3) Wrap C-clamp around rollbar, hand tighten the allen-head bolts
4) Insert left/right slide rails into REFLEX Soundbar, some vehicles will require
the use of the rotation bracket, allowing adjustments up to +/- 10 degrees
5) Carefully set the REFLEX Soundbar on top of the C-clamp, hand tighten the
allen head screws
6) Center the REFLEX Soundbar, permanently tighten all the allen bolts and nuts
Your Rollbar
Rubber Bushing
ROTATE
BRACKET OPTIONS
ROLLBAR / CAGE MOUNT
ALIGN CONNECTOR
PINS, INSERT and
HAND TIGHTEN
1.5” 1.75” 2.00”
FLUSH MOUNT
SURFACE MOUNT
NEVER CONNECT +12V
TO THE DOME WIRE
LED DOME - ON/OFFMUTE - ON/OFF STATUS INDICATOR
WHITE = ON
RED = STANDBY
CAUTION:
NEVER CONNECT THE MFC DIRECTLY
TO THE BATTERY, ALWAYS USE AN
ACCESSORY SWITCH
CAUTION!!
Never use USB
or AUX while in
mud and/or water
Close USB cover
when not in use
407"
ONBOARD CONTROL PANEL
Some applications may require
optional friction tape between
rubber bushings for a secure,
WLJKW¿WWKLVFDQEHIRXQGDW
most local hardware stores
1) Always check mounting depth before cutting
8VHWKHÀXVKEH]HODVWHPSODWH
&XWRXWKROHH[DFWO\
,QVHUWÀXVKPRXQWEH]HOSXVKVLGHWDEVRXWZDUGV
8VHRSWLRQDOVLOLFRQJOXHWRJLYHH[WUDKROG
6) Insert MFC
1) Check mounting depth before drilling
8VHWKHÀXVKEH]HODVWHPSODWH
'ULOORUFXWZLUHKROHH[DFWO\
,QVHUWUXEEHUWULPDURXQGÀXVKEH]HO
screw in place
5) Insert MFC
MFC can rotate 90ofor the
best mounting position
3mm Allen Head
3mm Allen Head
OPTIONAL
OPTIONAL
OPTIONAL TOOLS NEEDED:
- Hand saw or Jigsaw
NOTE!!
7RFRQVHUYHEDWWHU\OLIHWKH/(''RPHOLJKWZLOODXWRPDWLFDOO\WXUQRႇDIWHU
10 minutes when MFC ACC is turned OFF
BOSS RECOIL SERIES
OPTIONAL SYSTEM
EXPANSIBILITY
87
4
23
A
9
3.5mm AUX-INPUT
USB 1A
CHARGING
NOT FOR AUDIO PLAYBACK
OPEN
ALWAYS CLOSE COVER WHEN
NOT IN USE NEVER USE WHEN
IN MUD and/or WATER
1
5
6
MFC RESET
LONG PRESS BOSS
LOGO FOR 10 SECONDS
Fender Washer
3mm Allen Head
THANK YOU
from
BOSS
AUDIO
SYSTEMS
FOR YOUR PURCHASE
There's a reason
we
have
been
a
leader
and
innovator
in
the
business since 1987.
Our
goal
is
for
you
to
be
completely
satisfied
with
your
purchase.
If
for
any reason
you
are unsatisfied, please
let
us
be
the
first
to
know.
Contact
our
Customer
Care
dept.
at
805.988.0192
WE
WANT
YOUR POSITIVE FEEDBACK
AND
REVIEWS!
www.bossaudio.com
1115
!O~S
AUDIO SYSTEMS
EIO~S
AUDIO SYSTEMS
3451
Lunar
Court
Oxnard, CA 93030
~
PLACE
I
P~STAGE
I
HERE
L___
IO~S
AUDIO SYSTEMS
LIMITED
WARRANTY
This
product
has
a manufacturer's warranty against defects
in
materials and workmanship
to
the
original purchaser
for
a period
of
one
year
from
the
date-of-purchase
(DOP).
This manufacturer warranty
is
non-transferable. The warranty
is
for
repair or replacement at the
sole discretion
of
BOSS
AUDIO
SYSTEMS
(BAS).
For
service under this warranty you need
to
return
the
product
to
BAS.
If
replaced,
BAS
reserves
the
right
to
replace
it
with
a new or reconditioned
product
of
the
same
or
similar design.
Your
product
may
qualify
for
a free extended warranty.
Please
see
www.bossaudio.com
for
the qualifications and details
of
this program.
Obtain Warranty Service
Within
the
first
30
days
from
the
original
DOP,
BAS
will
provide a return shipping label
for
any defective
product
shipped
from
within
the
50
US
States. After the first
30
days
you
are
responsible
for
the
freight charges incurred
to
send the
product
back
to
BAS.
To
send a
product
in
for
warranty service you
will
need
the
following:
• A Return Authorization number
(RA#).
Please
contact
our
Technical Support
Team
to
receive a
RA#.
• A legible copy
of
the
proof-of-purchase
with
your name,
the
name
of
the authorized dealer,
the
DOP and the model number
of
the
product
requiring service.
• Enclose a
note
stating the problem or
issues
with
the product, your daytime phone number, email and return shipping address
(within
the
USA,
no
P.O.
Box
please).
This warranty does
not
cover any product subjected
to
abuse,
neglect, incorrect wiring, water
or
physical damage or any
attempt
to
repair
or
modify
the
product
by anyone
other
than
an
BAS
Repair Technician. Any damages, resulting
from
legal action
for
breach
of
expressed or implied warranty shall
be
limited
to
the cost
of
the
original purchase price
of
the
product. All liability
for
coincidental
damages
are
excluded under this warranty. The Customer
agrees
to
retain the original proof-of-purchase
for
establishing
the
effective
date
of
this warranty.
If
BAS
or
an
Authorized Dealer replace your
product
under warranty, the replacement
product
shall
be
considered
a transaction under the original warranty, and does
not
extend
the
original warranty period.
FOLD
HERE
To
register this product fill-in this form and mail this card
to
the address shown on
the
reverse side.
For
online registration,
see
reverse side
of
this card for instructions.
NAME
AGE
ADDRESS
CITY
STATE
ZIP
E-MAIL
PHONE
MODEL NO.
DATE
OF
PURCHASE PURCHASE
PRICE
PURCHASED
FROM
INSTALLED
BY
SERIAL
NUMBER
{If applicable)
VEHICLE:
YEAR,
MAKE
AND MODEL
1115
Table of contents
Other BOSSCO Stereo System manuals
