Boston Acoustics P4FL User manual

P4FL
Vertical Floor Stand for the P4, Bravo®II, and Bravo Speakers

P4 Assembly Instructions:
This configuration is compatible with Models: P460,
P450, P442, and P430.
•Flat head
Screwdriver
Hardware: (Per Speaker Stand)
Required Tools:
(not included)
•Phillips head
Screwdriver
Speaker
Screw
(short) x 2
Threaded
Machine
Screw x 3
P4FL
Base x 1
P4FL
Vertical
Post x 1
Step One: Attach Base
Attach the base to the vertical
post with the three included
threaded machine screws and
split washers (small) using a
Phillips head screwdriver. The
post has already been threaded
to ease screw installation. Attach
rubber feet to base.
Step Two: Speaker Wire
With the stand still inverted, route
the speaker wirethrough the open-
ing in bottom of the base, down
through, and out the opening in
the post. Leave several extra inches
of speaker wire exposed to ease
connection with the P4 speaker.
Split Washer
(small) x 3
Step Three: Mounting the P4 Speaker
There are two heights available for vertical mounting allowing you
to match the height of the speakers with your television. The
higher option is illustrated on the left and the lower on the right.
The total difference in height is 2-inches (51mm). Due to the weight
of the P4 speaker, it is recommended that the installation be
performed with the P4 speaker laying face down with the grille
removed on a soft surface such as a plush carpeted floor or the P4
shipping carton. Inspect the area where the speaker will lay making
sure that there are no objects that could damage the speakers or
scratch the front of the P4.
1. Position the P4FL close to the P4 speaker as illustrated.
2. Connect the speaker wire to the terminals on the P4 speaker.
3. Mount the speaker to the post by lining up the appropriate
threaded inserts in the back of the P4 speaker with the
machined holes in the post. Use the “P4 Mounting Chart” on
the back page of this manual to determine the correct
threaded inserts to use. Insert the two speaker screws (short)
and tighten. Note: Do not over-tighten the screws.
4. Insert the three hole plugs in the unused mounting holes on
the back of the P4FL post.
5. Take up any slack in the speaker wire by gently pulling the wire
at the opening in the base.
Hole Plug
x 3

Bravo Assembly Instructions:
This configuration is compatible with Models: Bravo II
and Bravo.
Hardware: (Per Speaker Stand)
Speaker
Screw
(long) x 2
Threaded
Machine
Screw x 3
P4FL
Base x 1
P4FL
Vertical
Post x 1
•Pliers
•Flat head
Screwdriver
•Phillips head
Screwdriver
Split Washer
(large)
x 2
1⁄4"-20
Threaded
Nut x 2
Split Washer
(small) x 3
Hole Plug
x 3
Step One: Attach Base
Attach the base to the vertical
post with the three included
threaded machine screws and
split washers (small) using a
Phillips head screwdriver. The
post has already been threaded
to ease screw installation. Attach
rubber feet to base.
Step Two: Speaker Wire
With the stand still inverted, route
the speaker wire through the open-
ing in bottom of the base, down
through, and out the opening in
the post. Leave several extra inches
of speaker wireexposed to ease
connection with the Bravo speaker.
Step Three: Mounting the Bravo Speaker
1. Using the speaker screws (long), washer, and 1⁄4"-20 threaded
nut, mount the Bravo mounting bracket to the P4FL post.
2. Remove the speaker’sgrille by grasping the back of the
cabinet in one hand, while gently pulling the grille away with
the other hand.
3. Connect the speaker wire to the terminals on the Bravo speaker.
4. Align the openings in the back of the speaker with the two
posts protruding from the bracket as shown and attach the
speaker to the bracket by inserting the supplied screws
through the holes in the front of the speaker and into the
bracket as shown.
Note: For detailed instructions on installing the speaker to the wall bracket,
please refer to the Bravo owners manual.
5. Insert the three hole plugs in the unused mounting holes on
the back of the P4FL post.
6. Take up any slack in the speaker wire by gently pulling the wire
at the opening in the base.
Required Tools:
(not included)

Boston, Boston Acoustics, Bravo, and the Boston Acoustics
logo are registered trademarks of Boston Acoustics, Inc.
Specifications aresubject to change without notice.
© 2004 Boston Acoustics, Inc.
300 Jubilee Drive
Peabody,MA 01960
U.S.A.
978.538.5000
www.bostonacoustics.com 042-002211-0
If Service Seems Necessary
First, contact the dealer from whom you purchased the speakers. If that is not possible, write to:
Boston Acoustics, Inc.
Attn: Parts and Service
300 Jubilee Drive
Peabody,MA 01960 U.S.A.
Or contact us via e-mail at:
suppor[email protected]
We will promptly advise you of what action to take. If it is necessary to return your P4FL floor stand to the factory,
please ship it prepaid. After it has been repaired, we will return it freight prepaid in the U.S.A. and Canada.
P4 Mounting Chart
Each P4 model features multiple mounting locations on the back of the speaker to accommodate a number of
different attachment methods. Below, the back of each model is shown along with the appropriate screw holes for
use with the P4FL speaker stand.
P450P460 P442 P430