Brähler Systems Weaver in the box User manual

Quick Guide
DIGIMIC Weaver in the box
Mini-PC with DCen Weaver for controlling multiple DCens
rticle no.:V4.4001

DIGIMIC Weaver in the box Quick Guide
Quick GuideQuick Guide
Quick Guide
2
BRÄHLER Systems GmbH
uf der lten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
V4.4001 QG 200113 V1.0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
Introduction and Connection
Introduction and ConnectionIntroduction and Connection
Introduction and Connection
The Mini-PC "Weaver in the box" is the cost-effective alternative for controlling conference systems with
several DIGIMIC central units (DCs). Using the DCen Weaver software, the Mini-PC connects the central
units within a few seconds and synchronizes them to a system. The DCens can be connected individually
according to your needs. When the system is switched on again, all already registered DCens are
automatically searched for and connected without further user intervention. Several DCens together behave
as if they were a single system.
Especially in combination with the software MicControl2 and/or CamControl your complete conference can
be controlled and managed via the Mini-PC "Weaver in the box".
USB 2.0
USB 3.0
microSD
card reader
LED
control lamp
On/Off
Headphone jack
3.5 mm
network
RJ45
HDMI
USB
Power supply

DIGIMIC Weaver in the box Quick Guide
Quick GuideQuick Guide
Quick Guide
3
BRÄHLER Systems GmbH
uf der lten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
V4.4001 QG 200113 V1.0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
C
CC
Construction
onstructiononstruction
onstruction
Provide a suitable power connection via the power supply. Now connect the Mini-PC to one of your DCens via
a network cable. You can add further DCens as required. Use the HDMI port to connect a monitor to the Mini-
PC - and connect the mouse and keyboard using the USB cable. The system is now ready for use.
To switch it on, press the on/off button - the LED control lamp lights up.
The system is controlled by the Weaver software. Please read the detailed instruction manual of the
software. The Mini-PC "Weaver in the box" is also designed for the MicControl and CamControl
software - please also read the corresponding operating instructions.
To switch off, press the on/off button of the Mini-PC again.
Warnings
WarningsWarnings
Warnings
The connections of the Mini-PC are designed and suitable exclusively for the intended cables and
devices. Do not connect any other devices!
In the case of a fault, contact a technician. Do not attempt to repair, unscrew or similarly repair the
Mini-PC yourself..

DIGIMIC Weaver in the box Quick Guide
Quick GuideQuick Guide
Quick Guide
4
BRÄHLER Systems GmbH
uf der lten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
V4.4001 QG 200113 V1.0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
Further information about our products can be found on the Internet under:
www.braehler-systems.com
© 2019
Copyright by BRÄHLER Systems GmbH, Königswinter
ll rights reserved, in particular (also in extracts) those of translation, reprinting, reproduction by copying or
similar procedures.
BRÄHLER Systems reserves the right to make technical changes without prior notice.
Brähler Systems GmbH
uf der lten Burg 6
53639 Königswinter, Germany
T [phone]
F [phone]
[e-mail]