Brilix XHPFD 80 E User manual

INVERTER
SWIMMING POOL HEAT PUMP
USER MANUAL
Illustrative photo
i
Read the instructions
EN
VERZE 8. 6. 2017 / REVIZE: 3. 11. 2017

2
Thank you to choose the Inverter swimming pool heat pump for your pool heating, it will
heat your pool water and keep the constant temperature when ambient temperature at
-10°C to 35°C.
Regulation (EU) n° 517/2014 of 16/04/14 on fluorinated greenhouse gases and repealing
Regulation (EC) n° 842/2006

3
ATTENTION: This manual includes all the necessary information with the use
and installation of your heat pump .
1. The installer must read the manual and attentively follow the instruction in implementation
and maintenance.
2. The installer is responsible for the installation of the product and should follow all the instructions
of the errors due to the installation that disobey the manual guideline. Any use that is without
conformity at the origin of its manufacturing will be regarded as dangerous.
WARNING : Please always empty the water in the heat pump during winter time or when
the ambient temperature drops below 0°C, or else the Titanium exchanger will be
damaged because of being frozen ,in such case ,your warranty will be lost.
WARNING : Please always cut the power supply if you want to open the cabinet to reach inside
the heat pump, because there is high voltage electricity inside.
WARNING : Please well keep the display controller in a dry area ,or well close the insulation
cover to protect the display controller from being damaged by humidity.
Index
1. Specification ......................................................................................................................................... 4
2. Dimension ..............................................................................................................................................7
3. Installation............................................................................................................................................. 8
4. Adjust the by-pass kit........................................................................................................................ 10
5. Initial operation ................................................................................................................................ 10
6. Controller Operation ........................................................................................................................ 12
7. Operation logic ................................................................................................................................ 15
8. Malfunction and Trouble shooting................................................................................................. 16
9. Electrical Wiring ............................................................................................................................... 18
10. Maintenance .................................................................................................................................... 19
11. Exploded view ..................................................................................................................................20

4
1. Specification
Model XHPFD 80 E XHPFD 100 E XHPFD 140 E
* Performance at Air 27°C, Water 27°C, Humidity 80%
Heating (Max./Std./Min.) kW - 10-2,3 -
Power consumption (Std.) kW - 1,52-0,18 -
C.O.P. (Std.) - 13-6,6 -
* Performance at Air 15°C, Water 26°C, Humidity 70%
Heating (Max./Std./Min.) kW - 7,1-1,9 -
Power consumption (Std.) kW - 1,4-0,25 -
C.O.P. (Std.) - 7,5-5,1 -
When water flows m3/h - 3.00 -
Voltage 220 ~ 240 V/50 Hz/1 PH
Std. Current Input A 3,7 4,6 5,4
Maximum Current A - 6,65 -
Minimum fuse A 18 18 18
Water in-out connection mm 50
Fan quantity 1
Ventilation type Horizontal
Compressor brand GMCC GMCC GMCC
Compressor type DC inverter Rotary
Noise level at 1m dB(A) 40-52 40-52 40-52
Coolant (R410a) kg 1,05 1,05 1,05
GWP 2088 2088 2088
CO2 Ekvivalent - tun 2,19
Net dimension mm 1045 x 415 x 695 1045 x 415 x 695
Net weight kg 65 65 78
Packing dimension mm 1140 x 430 x 745 1140 x 430 x 745
Gross weight kg 70 77 83
* Above data may be modified without notice.
* Obsahuje fluorované skleníkové plyny

5
Model XHPFD 160 E XHPFD 210 E XHPFD 260 E
* Performance at Air 27°C, Water 27°C, Humidity 80%
Heating (Max./Std./Min.) kW 17-3,8 - -
Power consumption (Std.) kW 2,54-0,29 - -
C.O.P. (Std.) 13-6,7 - -
* Performance at Air 15°C, Water 26°C, Humidity 70%
Heating (Max./Std./Min.) kW 11,5-3 - -
Power consumption (Std.) kW 2,2-0,37 - -
C.O.P. (Std.) 8.2-5.2 - -
When water flows m3/h 5.00
Voltage 220 ~ 240 V/50 Hz/1 PH
Std. Current Input A 7,2 9 11,9
Maximum Current A 11,31 25 32
Minimum fuse A 31
Water in-out connection mm 50
Fan quantity 1 2
Ventilation type Horizontální
Compressor brand MITSUBISHI MITSUBISHI PANASONIC
Compressor type stejnosměrný, se střídačem, rotační
Noise level at 1m dB(A) 41-56 41-56 41-56
Coolant (R410a) kg 1,7 1,7 1,7
GWP 2088 2088 2088
CO2 Ekvivalent - tun 3,55
Net dimension mm 1070 x 410 x 850
Net weight kg 95 - 130
Packing dimension mm 1140 x 430 x 990 1150 x 450 x 1360
Gross weight kg 110 - 142
* Above data may be modified without notice.
* Obsahuje fluorované skleníkové plyny

6
Model XHPFD 260 EII XHPFD 350 E XHPFD 350 EII
* Performance at Air 27°C, Water 27°C, Humidity 80%
Heating (Max./Std./Min.) kW 26-13 33-16,5 33-6,5
Power consumption (Std.) kW 2,56 3,26 3,26
C.O.P. (Std.) 7,6 7,6 7,6
* Performance at Air 15°C, Water 26°C, Humidity 70%
Heating (Max./Std./Min.) kW 20-10 25-12,5 25-12,5
Power consumption (Std.) kW 2,67 3,34 3,34
C.O.P. (Std.) 5,6 5,6 5,6
When water flows m3/h
Voltage 380 V/50 Hz/3 PH 220 ~ 240 V/50 Hz/1 PH 380 V/50 Hz/3 PH
Std. Current Input A 5,1 14,9 6,4
Maximum Current A 15 40 18
Minimum fuse A
Water in-out connection mm 50
Fan quantity 2
Ventilation type Horizontální
Compressor brand PANASONIC
Compressor type stejnosměrný, se střídačem, rotační
Noise level at 1m dB(A) 52 52 52
Coolant (R410a) kg
GWP
CO2 Ekvivalent - tun
Net dimension mm 1050 x 430 x 1215
Net weight kg 130 145 145
Packing dimension mm 1150 x 450 x 1360
Gross weight kg 142 157 157
* Above data may be modified without notice.
* Obsahuje fluorované skleníkové plyny

7
2. Dimension
XHPFD 100 E
XHPFD 160 E

8
3. Installation
(1) The heat pump unit must be installed by professional technicians .otherwise unit may be
damaged or body injured, even dead
(2) The unit is designed for outdoor location with good ventilation. Recirculation of cold
discharge air back into evaporator coil will greatly reduce heating capacity and efficiency
of the unit, which will void the compressor warranty.
(3) The unit can be installed almost anywhere in the outdoors. To get a good performance, it
needs to meet the three factors :
a) Good ventilation
b) Stable and reliable power supply
c) Recycled water system
The difference from gas water heater, it should not bring environmental pollution or have
the installing problems in-windy areas.
(4) The unit should not be installed in a limited air ventilation area ,or placed in a bush where
it will block the air inlet .
These location deny the unit of a continuous source of fresh air .When seasons changing, it
may stick leaves on the evaporator coil , thereby reducing its efficiency and impact of its
service life .
(5) For indoor installation, please consult more instruction from technicians.
(6) When install a bypass, it should be not exceed 30% of nominal flow rate.
(7) Must make Water level higher than the circulation pump location.
(8) Below picture show the minimum required distance on each side of pool heat pump unit.
(9) Typically, the pool heat pump unit should be installed aside the pools, less than 7.5 meters
distance.
(10) To get the best heat exchange of heat pump unit, it should be matched the normal rate of
water flow recommended in specification sheet.
(11) It is required to increase the discharge pipe to prevent freezing in cold season, to put T
fitting and ball valve to facilitate changing the water in winter or emptying the water out
of system to prevent freezing when HP stop operating at the ambient temperature below
zero ,otherwise the unit may be damaged .
(12) It is suggested to install the quick adapter in front of water in-out connection, which could
discharge water easily to prevent water freezing, and be convenient for maintenance and service.
(13) When unit running ,there will be some condensation water discharged from the bottom,
please hold the drainage nozzle (accessory ) into the hole and clip well ,and then connect
a pipe to drain the condensation water out.

9
(14) If water pressure is over 10 KPA, or water flow rate is more than 11 cubic meters through
heat exchanger, it is necessary to install the by-pass pipe in water system.
(15) Installation illustration
NOTE: The factory only provides the heat pump unit. The other items in the
illustration are necessary spare parts for the water system which are provided
by users or installers.
ATTENTION: Please follow these steps when operating the first time :
1. Open the derivation valves for charge water and close the valve (direct)
2. Make sure that the pump and the water-in pipe have been filled with water
3. Start the unit
(16) The location of chemical’s instruction to your system is also critical to the heater’s life.
If an automatic chlorinator or brominates is used, it must be located downstream
of the heater.
A trap must be installed between the chlorinator and the heater to prevent chlorine return
into the heat pump. (See below pictures)
A. Bypass connection
1. Sump
2. Filter
3. Return valve
4. Return valve
5. Water treatment
6. Pump
B. Series connection (in-line)
7. Sump
8. Filter
9. Return valve
10. Water treatment
11. Pump
2.
4.
1.
3.
5.
6.
8.
11.
7.
9.
10.
A.
B.
A Swimming pool
B Filter
C Pump
D Heat pump
A
B
D
C

10
4. Adjusting the bypass
Use the following procedure to adjust the bypass:
• fully open all three valves
• slowly close valve 1 until the water pressure is increased by approximately 100 to 200 g
• Close valve 3 approximately half-way to adjust the gas pressure in the cooling system
• If the display shows „ON“ or error code EE3, close step by step the valve 2, to increase
water flow and stop when the code disappear.
Optimal operation of the heat pump occurs when the cooling gas pressure is 22 ±2 bar.
This pressure can be read on the pressure gauge next to the control heat pump panel. Under
these conditions the water flow through the unit is also optimal.
Note: Operation without a bypass or with improper bypass adjustment may result in sub-optimal heat
pump operation and possibly damage to the heat pump, which renders the warranty null and void.
5. Initial operation
Note: In order to heat the water in the pool (or hot tub), the filter pump must be running to
cause the water to circulate through the heat pump. The heat pump will not start up if the
water is not circulating.
After all connections have been made and checked, carry out the following procedure:
1. Switch on the filter pump. Check for leaks and verify that water is flowing from and to the
swimming pool.
2. Connect power to the heat pump and press the On/Off button on the electronic control
panel. The unit will start up after the time delay expires (see below).
3. After a few minutes, check whether the air blowing out of the unit is cooler.
4. When turn off the filter pump , the unit should also turn off automatically, if not, then
adjust the flow switch.
5. Allow the heat pump and the filter pump to run 24 hours a day until the desired water
temperature is reached. The heat pump will stop running at this point. After this, it will
restart automatically (as long as the filter pump is running) whenever the swimming pool
water temperature drops 2 degree below the set temperature.
BYPASS
6
Discharge connection
7 8
1
2
3
4 5
1. Valve 1
2. Valve 2
3. Valve 3
4. Outside
5. Inside
6. Pump
7. To swimming pool
8. From the filter