Brilix XHPFDPLUS60 User manual

Swimming Pool Heat Pump
USER
MANUAL
Illustrative photo
i
Read the instructions

2
Regulation (EU) n° 517/2014 of 16/04/14 on fluorinated greenhouse
gases and repealing Regulation (EC) n° 842/2006
Leak checks
1. Operators of equipment that contains fluorinated greenhouses gases in quantities of 5 tons of CO2,
equivalent or more and not contained in foams shall ensure that the equipment is checked for leaks.
2. For equipment that contains fluorinated greenhouse gases in quantities of 5 tons of CO2 equivalent
or more, but of less than 50 tons of CO2 equivalent: at least every 12 months.
Picture of the equivalence CO2
1. Load in kg and Tons amounting CO .
2
Concerning the Gas R32, 7.40kg amounting at 5 tons of CO2, commitment to check
each year.
Training and certification
1. The operator of the relevant application shall ensure that the relevant personnel have obtained
the necessary certification, which implies appropriate knowledge of the applicable regulations and
standards as well as the necessary competence in emission prevention and recovery of fluorinated
greenhouse gases and handling safety the relevant type and size of equipment.
Record keeping
1. Operators of equipment which is required to be checked for leaks, shall establish and maintain
records for each piece of such equipment specifying the following information:
a) The quantity and type of fluorinated greenhouse gases installed;
b) The quantities of fluorinated greenhouse gases added during installation, maintenance or servicing
or due to leakage;
c) Whether the quantities of installed fluorinated greenhouse gases have been recycled or reclaimed,
including the name and address of the recycling or reclamation facility and, where applicable, the
certificate number;
d) The quantity of fluorinated greenhouse gases recovered
e) The identity of the undertaking which installed, serviced, maintained and where applicable repaired
or decommissioned the equipment, including, where applicable, the number of its certificate;
f) The dates and results of the checks carried out;
g) If the equipment was decommissioned, the measures taken to recover and dispose of the fluorinated
greenhouse gases.
2. The operator shall keep the records for at least five years, undertakings carrying out the activities
for operators shall keep copies of the records for at least five years.
Load and Tons amounting Co2Frequency of test
From 7 at 75 kg load = from 5 at 50 Tons Each year
Do no release R32 coolant liquid into the atmosphere. This is a fluoride greenhouse
effect gas covered by the Kyoto agreement with a global warming potential (GWP)
= 675 - (see the European Community regulations on fluoride greenhouse effect gases
Regulation (EU) No 517/2014).
1

Thank you for using BRILIX swimming pool heat pump four your pool heating it will heat your pool water
and keep the constant temperature when ambient temperature at -5 to 35 °C.
In order to offer qualified, reliable and flexible heat pump unit to our customer, please read this manual
carefully before installing, operating and troubleshooting, then process accordingly.
This manual includes all necessary information.
Index
ATTENTION:
• Operating and maintaining according to recommended time and frequency on manual.
• Use only standard spare parts.
3
1.Specifications
........................................................................................................................................... 3
2.Installation
............................................................................................................................................... 5
3.Initial Startup of the unit
.......................................................................................................................... 9
6.Maintenance ...........................................................................................................................................20
5.Operation
....................................................................... ........................................................................
...15
4.Wiring diagram
.......................................................................................................................... 10
Swimming Pool Heat Pump Inverboost C / 3
1. Dimension .................................................................................................................. 4
2. Transport information .............................................................................................. 6
3. Specifications .............................................................................................................7
4. Accessories and options ......................................................................................... 8
5. Location and connection ...................................................................................... 10
6. Electrical Wiring .......................................................................................................13
7. Initial operation ........................................................................................................15
8. Troubleshooting ...................................................................................................... 23
9. Exploded view .........................................................................................................30
10. Maintenance ............................................................................................................ 34
11. Winterization ............................................................................................................34
Thank you for using BRILIX swimming pool heat pump for your pool heating, it will heat your pool
water and keep the constant temperature when the air ambient temperature is at 10 to 43°C.
Index
Important notice:
1 Please always keep the heat pump in a well ventilated place and away from anything
which could cause fire.
2 Do not braze or weld the pipe if there is refrigerant inside machine. Please do not
charge the gas when in a confined space.
3 Please always empty the water in heat pump during winter time or when the ambient
temperature drops below 0 °C, or else the Titanium exchanger will be damaged
because of being frozen, in such case, your warranty will be lost.
4 Please always cut the power supply if you want to open the cabinet to reach inside the
heat pump.
5 Please keep the display controller in a dry area to protect the display controller from
being damaged by humidity.
6
Action of filling gas must be conducted by professional with R32/R410A operating license.
ATTENTION: This manual includes all the necessary information for the use and
the installation of your heat pump.
• The installer must read the manual and follow the instructions of implementation and
maintenance.
• The installer is responsible for the installation of the product and should follow all the
instructions of the manufacturer and the regulations in application. Incorrect installation
will invalidate the guarantee.
• The manufacturer declines any responsibility for the damage caused by any third party,
object ingression and of the errors due to the installation that do not follow the manual
guidelines. Any use that is not as intended by the manufacturer will invalidate the guarantee.
2

1.Specifications
1.1 Horizontal EU design, R32, HEATING AND COOLING
4
Models
* Heating Capacity at Air 28℃, Water 28℃,Humidity 80%
Heating capacity
Power consumption
COP
* Heating Capacity at Air 15℃, Water 26℃,Humidity 70%
Heating capacity
Power consumption
COP
* General data
Compressor type
Voltage
Rated Current
Minimum fuse
Advised pool volume
(with pool cover)
Advised water flux
Water Pressure Drop
Heat exchanger
Water connection
Ventilation type
Fan Speed
Noise level(10m)
Noise level(1m)
Refrigerant (R32)
CO equivalent
2
* Dimension/ Weight
Net Weight
Gross Weight
Net Dimension
Packing Dimension
* Above data are subjects to modification without notice.
XHPFDPLUS60 XHPFDPLUS100 XHPFDPLUS140 XHPFDPLUS160
kW
kW
kW
kW
A
A
m³
m³/h
Kpa
mm
RPM
dB(A)
dB(A)
g
Tonne
kg
kg
mm
mm
44 51 61 72
47 55 65 76
977/360/554 1047/344/621
1060/380/580 1120/380/660
912 15
5
1,44 1,92 1,92 0,8
6,25 6,25 6,256,25
3,65
0,81
4,5
6,57
1,42
4,5
9
1,92
4,6
9,45
1,92
4,9
Rotary/R32
220-240V~50Hz/1PH
4,5
10
0-20
2,5~3,2
12
7,1
20
25-40
2,8~5,6
15
9,5
25
35-60
3,5~7,1
15
9,5
25
40-65
4~7,9
15
Titanium in PVC
50
Horizontal
830~870 650
35
44
400
0,27
36
45
650
0,44
37
46
850
0,58
42
51
900
0,61
1095/409/696
1160/430/720
3

1.2 Horizontal EU design, R410A ,HEATING AND COOLING
Above data is subject to modification without notice.
Models XHPFD40 XHPFD60 XHPFD100 XHPFD140 XHPFD160 XHPFDPLUS 200
XHPFDPLUS 200 Tri
*Capacity at 25 °C/Water27 °C
Heat Output (kW) 3,55,09,0 12,0 15,0 18,018,0
Power Consumption (kW) 0,56 0,80 1,44 1,92 1,92 2,88 2,88
COP 6,25 6,25 6,25 6,25 6,25 6,25 6,25
*
Heat Output (kW) 2,56 3,65 6,57 9,09,45 13,50 13,50
Power Consumption (kW) 0,61 0,81 1,42 1,92 1,92 2,72 2,72
COP 4,04,54,54,64,94,89 4,89
Voltage (V) 220−240 V
Rated Current (A) 3,24,57,19,59,5 14,25,5
Advised Fuse (A) 10,0 10,0 20,0 20,0 20,0 35,015,0
*Water data
Advised pool volume (m
3
)0-15 0-20 25-40 35-60 40-65 60-90 60-90
Advised water flux (m
3
/h) 4,24,26,08,49,0 10,210,2
Water pipe in-out spec (mm) 50,0
*General Data
Compressor
Air flow horizontal
Condenser titanium in PVC
Noise level at 10 m (dB(A)) 35,0 35,0 36,0 37,0 42,0 42,042,0
Noise level at 1 m (dB(A)) 44,0 44,0 45,0 46,0 51,0 51,051,0
Water pressure (kPa) 12,0 12,0 15,0 15,0 15,0 16,016,0
Refrigerant (kg) 0,42 0,45 0,91,11,31,71,8
*
Net Dimension(mm)751/300/502 935/360/545 935/360/545 1005/360/620
1045/410/695 1045/410/850 1045/410/850
Net Weight (kg) 33 44 51 61 72 100 100
Packing Dimension (mm)
850/330/540 1060/380/590 1060/380/590 1120/380/660 1140/430/740 1140/430/990 1140/430/990
Gross weight(kg)35 47 55 65 76 110 110
Scroll Scroll
Capacity at 15 °C/Water 27 °C
Dimension and Weight
Rotary RotaryRotary
380−415 V
5
1.2 Horizontal EU design, R410A ,HEATING AND COOLING
Above data is subject to modification without notice.
Models XHPFD40 XHPFD60 XHPFD100 XHPFD140 XHPFD160
XHPFDPLUS 200
XHPFDPLUS 200 Tri
*Capacity at 25 °C/Water27 °C
Heat Output (kW) 3,55,09,0 12,0 15,0 18
,018,0
Power Consumption (kW) 0,56 0,80 1,44 1,92 1,92
2,88 2,88
COP 6,25 6,25 6,25 6,25 6,25 6
,25 6,25
*
Heat Output (kW) 2,56 3,65 6,57 9,09,45 13
,50 13,50
Power Consumption (kW) 0,61 0,81 1,42 1,92 1,92 2
,72 2,72
COP 4,04,54,54,64,94
,89 4,89
Voltage (V)
220−240 V
Rated Current (A) 3,24,57,19,59,5 14
,25,5
Advised Fuse (A) 10,0 10,0 20,0 20,0 20,0 35
,015,0
*Water data
Advised pool volume (m
3
)0-15 0-20 25-40 35-60 40-65 60
-90 60-90
Advised water flux (m
3
/h) 4,24,26,08,49,0 10
,210,2
Water pipe in-out spec (mm)
50,0
*General Data
Compressor
Air flow
horizontal
Condenser
titanium in PVC
Noise level at 10 m (dB(A)) 35,0 35,0 36,0 37,0 42,0 42
,042,0
Noise level at 1 m (dB(A)) 44,0 44,0 45,0 46,0 51,0 51
,051,0
Water pressure (kPa) 12,0 12,0 15,0 15,0 15,0 16
,016,0
Refrigerant (kg) 0,42 0,45 0,91,11,3
1,71,8
*
Net Dimension(mm)751/300/502 935/360/545 935/360/545 1005/360/620
1045/410/695 1045
/410/850 1045/410/850
Net Weight (kg) 33 44 51 61 72
100 100
Packing Dimension (mm)
850/330/540 1060/380/590 1060/380/590 1120/380/660 1140/430/740 1140
/430/990 1140/430/990
Gross weight(kg)35 47 55 65 76
110 110
Scroll Scroll
Capacity at 15 °C/Water 27 °C
Dimension and Weight
Rotary RotaryRotary
380−415 V
5
4

6
2.Installation
2.1 Installation illustration
NOTE: The factory only provides the heat pump unit. The other items in the illustration are necessary spare
parts for the water system which are provided by users or installers.
ATTENTION:
Please follow these steps when operating the first time
1. Open valve and charge water.
2. Make sure that the pump and the water-in pipe have been filled with water.
3. Close the valve and start the unit.
Horizontal
Water
treatment
By-pass
Pump Filter
Hot water to pool
800 mm
min.
- Please always keep the heat pump in the ventilation place and away from anything which
could cause fire.
- Don’t weld the pipe if there is refrigerant inside machine. Please keep the machine out of the
confined space when make gas filling.
- Action of filling gas must be conducted by professional with R32 operating license.
Important NOTE:
5

2.2 Installation
(1) The heat pump unit must be installed by professional technicians. Otherwise unit may be damaged or
body injured, even dead.
(2) The unit designed for outdoor location with good ventilation. Recirculation of cold discharge air back
into evaporator coil will greatly reduce heating capacity and efficiency of the unit, which will avoid the
compessor warranty.
(3) The unit can be installed almost anywhere in the outdoors. To get a good performance, it needs to meet
the three factors:
a) Good ventilation
b) Stable and reliable power supply
c) Recycled water system
The difference from gas water heater, it should not bring environmental pollution or have the installing
problems in-windy areas.
(4) The unit should not be installed in a limited air ventilation area, or placed in a bush where it will block
the air inlet. These location deny the unit of a continuous source of fresh air. When seasons changing,
it may stick leaves on the evaporator coil, thereby reducing its efficiency and impact of its service life.
(5) For indoor installation, please consult more instructions from technicians.
(6) When install a bypass, it should be not exceed 30 % of nominal flow rate
(7) Must make Water level higher than the circulation pump location.
(8) Below picture show the minimum required distance on each side of pool heat pump unit.
Air inlet
Air outlet
7
6

(9) Typically, the pool heat pump unit should be installed aside the pools, less than 7.5 meters distance. If
it is installed farther away, the pipeline system will cause greater heat loss. The most of pipeline are
installed under ground , although the pipeline. system has to do thermal insulation ,but tunnels and the
soil around will still occur heat exchange , for example, each 30 meters ( 15 meters to and from the
pump=30 meters total),unless the ground is wet or the water table is high. A very rough estimate of heat
loss per 30 meters is 0.6KW per hour (2000BTU) for every 5 °C surrounding the pipe, which translates
to about 3% to 5% increase in run time.
(10) To get the best heat exchange of heat pump unit, it should be matched the normal rate of water flow
recommended in specification sheet.
(11) It is required to increase the discharge pipe to prevent freezing in cold season , to put “T” fitting and
ball valve to facilitate changing the water in winter or emptying the water out of system to prevent
freezing when HP stop operating at the ambient temperature below zero, otherwise the unit may be
damaged .
(12) It is suggested to install the quick adaptor in front of water in-out connection, which could discharge
water easily to prevent water freezing, and be convenient for maintenance and service.
(13) When unit running , there will be some condensation water discharged from the bottom ,please hold
the drainage nozzle (accessory) into the hole and clip well , and then connect a pipe to drain the
condensation water out.
(14) If water pressure is over 10 KPA , or water flow rate is more than 11 cubic meters through heat exchanger,
it is necessary to install the by-pass pipe in water system.
8
7

2.3 The location of chemical’s instruction to your system is also critical to the heater’s life.
If an automatic chlorinator or brominates is used, it must be located downstream of the heater. A trap must
be installed between the chlorinator and the heater to prevent chlorine return into the heat pump. (See below
pictures)
Pressure-type Chlorinator or Brominator
Check-valve
Chlorinator
Filter
Water pump
Check-valve
P-trap
9
8

10
DISCONNECT: A disconnect means (circuit breaker, fused or un-fesed switch) should be located within
sight of and readily accessible from the unit. This is common practice on commercial and residential heat
pumps. It prevents remotely-energizing unattended equipment and permits turning off power at the unit
Please make sure the water pump is running in circulation with adequate rate of water flow.
Startup Procedure after Installation is completed, and please follow these steps:
(1) Turn on your filter pump ,check water leaks and verify flow of swimming pool.
(2) Turn on the electrical power supply to the unit, then press the key ON/OFF of wire controller, it should
start in several seconds.
(3) After running a few minutes make sure the air ventilation from the side (top) of the unit is cooler
(Between 5 °C and10 °C).
(4) When turn off the filter pump, the unit should also turn off automatically , if not, then adjust the flow
switch.
(5)
Water Flow Switch:
Time Delay:
Allow the unit and pool pump to run 24 hours per day until the water reaches the desired
temperature. When the temperature reaches the setting value ,the HP unit will shut down, when
the pool temperature drops more than 2 °C, the heat pump will restart automatically.
It is equipped with a flow switch for protecting the HP unit running adequate water flow rate.
It will turn on when the pool pump runs and shut it off when the pump shuts off. If the pool water
level higher than 1 m above or below the heat pump‘s automatic adjustment knob, your dealer may
need to adjust its initial startup.
HP unit should be equipped with a 3-minute built-in solid-state restart delay protection. Time delay
control is an integral part of the circuit control, it can eliminate restart cycling and contactor chatter.
The time delay will automatically restart the HP unit approximately 3 minutes after each control
circuit interruption. Even a brief power interruption will activate the solid state 3 minute restart
delay and prevent the unit from the starting until the 3 minutes countdown is completed.
while the unit is being serviced.
3.Initial Startup of the unit
NOTE:
9

11
4.Wiring diagram
Model: XHPFDPLUS60 & XHPFDPLUS100
* The dotted line part are only used in some models
RUN/POW
SWITCH
2
2
2
2
3
Low Pressure switch
5
Electronic Expansion Valve
LED controller
High Pressure switch
Water out temperature
Water in temperature
Heating pipe temperature
Ambient temperature
Phase sequence protection
YLW/GRN
2
Transformer
2
220-240V ~ 50Hz
Fan Motor
RED
ORG
C1
BLK
COMPRESSOR
S BLK
C2
R WHT
WHT
4-WAY
BLU
BLU
BRN
BRN
BRN
BRN
BLU
BLK
BLU
C RED
RED
BLU
AC-N
RED
RED
Water flow switch
SW1
BRN
BLU
YLW
Remote controller
Base Electric Heater
YLW/GRN
YLW/GRN
OUT1
OUT2
OUT3
3-XPDLT0012S
PE
PE
PE
LN
(Water Pump)
10

12
* The dotted line part are only used in some models
RUN/POW
2
2
2
2
2
3
Low Pressure switch
Water flow switch
5
Electronic Expansion Valve
Controller
High Pressure switch
Water out temperature
Water in temperature
Heating pipe temperature
Ambient temperature
Back temperature
Phase sequence protection
2
Transformer
2
FAN MOTOR
RED
ORG
C1
YLW/GRN
BLK
COMPRESSOR
YLW/GRN
S BLK
C2
R WHT
WHT
4-WAY
BLU
BRN
OUT1
OUT2
33
44
OUT3
OUT4
OUT5
AC-N
CN1 SW1
CN5
CN4
CN2
BRN
BLU
RED
BLU
C RED
BLU
RED
AC CONTACTOR
BRN
BLU
Remote controller
Base Electric Heater
YLW/GRN
220-240V ~ 50Hz
BLU
BRN
3-XPDLT0022S
PE
LN
SWITCH
BRN
RED
(Water Pump)
Model: XHPFDPLUS160XHPFDPLUS140 &
Note: Electrical connection
The power supply for the heat pump must come, preferably, from an exclusive circuit with regulatory
protection components (30mA differential protection) and a magneto-thermal switch.
- The electrical installation must be carried out by a specialized professional (electrician) in accordance
with the standards and regulations in force in the country of installation.
- The heat pump circuit must be connected to a safety earth circuit at the terminal block.
11

12
5.3 Schéma zapojení bazénového tepelného čerpadla
XHP 200, XHPFD200
* The dotted line part are only used in some models
RUN/POW
2
2
2
2
2
3
Low Pressure switch
5
Electronic Expansion Valve
LED controller
High Pressure switch
2
Water out temperature
Water in temperature
Heating pipe temperature
Ambient temperature
Back temperature
Phase sequence protection
LN
2
Transformer
2
FAN MOTORR
RED
ORG
C1
FAN MOTORR
RED
ORG
C1
BLK
BLK
COMPRESSOR
YLW/GRN
S BLK
C2
R WHT
WHT WHT
4-WAY
BLU
BRN
BRN
BLU
RED
BLU
C RED
BLU
RED
AC CONTACTOR
BRN BLU
12
BLU
BLU
N
Water flow switch
SWITCH
220-240V ~ 50Hz
Cooling pipe temperature
Remote controller
BRN
BLU
YLW
SW1
AC CONTACTOR
Crankcase heater
1 / L1
21
2/T122
N
temperature
controller
YLW/GRN
YLW/GRN
YLW/GRN
YLW/GRN
OUT3
OUT1
OUT4
OUT2
3
34
4
OUT5
AC-N
CN1 CN2
CN4
Base Electric Heater
3-XPDLT0032
Model: XHPFDPLUS 200
12

5.4 Schéma zapojení bazénového tepelného čerpadla
XHP 200 Tri ,XHPFD200 Tri
* The dotted line part are only used in some models
BLU
BLU
2
Transformer
5
Electronic Expansion Valve
Current
checking
L1
Current
checking
RUN
K1
1 3 42
ON
R
S T
N
ABCN
12
2
2
2
POW
RED
ORG
U/T1
RED
YLW/GRN
BLK
WHT
AC CONTACTOR
RED
BLK
WHT
RED
BLK
WHT
RED
RED
RED
BRN
L4
BLK
WHT
W/T3
V/T2
YLW/GRN
YLW/GRN
YLW/GRN
LED
OUT2
OUT1
OUT3 OUT4 OUT5
AC-N
CN1
CN2
4-WAY VALVE
3
Low voltage switch
Remote controller
High voltage switch
Phase sequence protection
CN3
SW1
BRN
BLU
YLW
12V
ENT
GND
GND
GND
GND
GND
GND
KYIN
FS
LP
HP
PP
2 2
2 2 2
2
Water out temperature
Water inlet coil temperature sensor
H coil temperature eating
Ambient emperature t
back temperature
CN4
GND
GND
GND
GND
GND
GND
T6 T5 T4 T3 T2 T1
COMPRESSOR
Programming
PC Board
FAN CAPACITOR
3434
FAN MOTOR
Crankcase heater
Crankcase
heater
BRN
BRN
BRN
BRN
temperature
controller
380-415V 3N 50Hz
~
Flow switch failure
cooling pipetemperature sensor
N
SWITCH
BLU
3-XPDLT0052
13
Model: XHPFDPLUS 200 Tri
13

5.4 Schéma zapojení bazénového tepelného čerpadla
XHP 200 Tri ,XHPFD200 Tri
* The dotted line part are only used in some models
BLU
BLU
2
Transformer
5
Electronic Expansion Valve
Current
checking
L1
Current
checking
RUN
K1
1 3 42
ON
R
S T
N
ABCN
12
2
2
2
POW
RED
ORG
U/T1
RED
YLW/GRN
BLK
WHT
AC CONTACTOR
RED
BLK
WHT
RED
BLK
WHT
RED
RED
RED
BRN
L4
BLK
WHT
W/T3
V/T2
YLW/GRN
YLW/GRN
YLW/GRN
LED
OUT2
OUT1
OUT3 OUT4 OUT5
AC-N
CN1
CN2
4-WAY VALVE
3
Low voltage switch
Remote controller
High voltage switch
Phase sequence protection
CN3
SW1
BRN
BLU
YLW
12V
ENT
GND
GND
GND
GND
GND
GND
KYIN
FS
LP
HP
PP
2 2
2 2 2
2
Water out temperature
Water inlet coil temperature sensor
H coil temperature eating
Ambient emperature t
back temperature
CN4
GND
GND
GND
GND
GND
GND
T6 T5 T4 T3 T2 T1
COMPRESSOR
Programming
PC Board
FAN CAPACITOR
3434
FAN MOTOR
Crankcase heater
Crankcase
heater
BRN
BRN
BRN
BRN
temperature
controller
380-415V 3N 50Hz
~
Flow switch failure
cooling pipetemperature sensor
N
SWITCH
BLU
3-XPDLT0052
13
12
* The dotted line part are only used in some models
RUN/POW
2
2
2
2
2
3
Low Pressure switch
Water flow switch
5
Electronic Expansion Valve
Controller
High Pressure switch
Water out temperature
Water in temperature
Heating pipe temperature
Ambient temperature
Back temperature
Phase sequence protection
2
Transformer
2
FAN MOTOR
RED
ORG
C1
YLW/GRN
BLK
COMPRESSOR
YLW/GRN
S BLK
C2
R WHT
WHT
4-WAY
BLU
BRN
OUT1
OUT2
33
44
OUT3
OUT4
OUT5
AC-N
CN1 SW1
CN5
CN4
CN2
BRN
BLU
RED
BLU
C RED
BLU
RED
AC CONTACTOR
BRN
BLU
Remote controller
Base Electric Heater
YLW/GRN
220-240V ~ 50Hz
BLU
BRN
3-XPDLT0022S
PE
LN
SWITCH
BRN
RED
(Water Pump)
Model: XHPFDPLUS160XHPFDPLUS140 &
Note: Electrical connection
The power supply for the heat pump must come, preferably, from an exclusive circuit with regulatory
protection components (30mA differential protection) and a magneto-thermal switch.
- The electrical installation must be carried out by a specialized professional (electrician) in accordance
with the standards and regulations in force in the country of installation.
- The heat pump circuit must be connected to a safety earth circuit at the terminal block.
13
5.Operation
5.1 The functions of LED wire controller
5.2 How to know operation parameter
(LED display show real time till HP unit is power off)
(1) Long press 5 seconds to enter operating parameter interface.
(2) Under parameter interface, Press or to check the parameters
(3) Leave it 8 seconds, LED will display water in temperature (under running) or time (until stops)
(4) Under current mode, press or to modify the water setting temperature whenever it is ON/OFF
status.
(5) While running, the LED displays the water-in temperature and current mode
LED display
Operation mode display
ON/OFF
Time button
Timer off button
Timer on button
Up and down button
- The cables must be properly installed to prevent interference.
- The pump is intended for connection to a general power supply with earth connection.
- Section of the cable; This section is indicative and should be checked and adapted according to the needs
and conditions of use.
- The tolerance of acceptable voltage variation is +/- 10% during operation.
The connections must be dimensioned according to the power of the device and the state of installation.
14

13
5.Operation
5.1 The functions of LED wire controller
5.2 How to know operation parameter
(LED display show real time till HP unit is power off)
(1) Long press 5 seconds to enter operating parameter interface.
(2) Under parameter interface, Press or to check the parameters
(3) Leave it 8 seconds, LED will display water in temperature (under running) or time (until stops)
(4) Under current mode, press or to modify the water setting temperature whenever it is ON/OFF
status.
(5) While running, the LED displays the water-in temperature and current mode
LED display
Operation mode display
ON/OFF
Time button
Timer off button
Timer on button
Up and down button
- The cables must be properly installed to prevent interference.
- The pump is intended for connection to a general power supply with earth connection.
- Section of the cable; This section is indicative and should be checked and adapted according to the needs
and conditions of use.
- The tolerance of acceptable voltage variation is +/- 10% during operation.
The connections must be dimensioned according to the power of the device and the state of installation.
13
5.Operation
5.1 The functions of LED wire controller
5.2 How to know operation parameter
(LED display show real time till HP unit is power off)
(1) Long press 5 seconds to enter operating parameter interface.
(2) Under parameter interface, Press or to check the parameters
(3) Leave it 8 seconds, LED will display water in temperature (under running) or time (until stops)
(4) Under current mode, press or to modify the water setting temperature whenever it is ON/OFF
status.
(5) While running, the LED displays the water-in temperature and current mode
LED display
Operation mode display
ON/OFF
Time button
Timer off button
Timer on button
Up and down button
- The cables must be properly installed to prevent interference.
- The pump is intended for connection to a general power supply with earth connection.
- Section of the cable; This section is indicative and should be checked and adapted according to the needs
and conditions of use.
- The tolerance of acceptable voltage variation is +/- 10% during operation.
The connections must be dimensioned according to the power of the device and the state of installation.
15

Parameter 2
Total working time of compressor
after frosting (30-90 min,default
setting : 40 min)
Parameter 5
Time of Exit defrosting (1 to 12
min, default setting 12 min)
Parameter 8
Heating target for superheat
(-15 °C-15 °C) default
setting: 3 °C
Parameter 1
To set the entering water temp.
under heating mode (15-40 °C,
default setting:28 °C)
Parameter 4
Terms of Exit defrosting
function (2 to 30 °C, default
setting 20 °C)
Parameter 7
Mode selection of Electronic
expansion valve ( 0 to 1),
default setting 1 (auto)
Parameter 0
To set the entering water temp.
under cooling mode (15-35 °C,
default setting: 28 °C)
Parameter 3
Terms of Entry defrosting
function (-30 °C to 0 °C, default
setting -7 °C)
Parameter 6
Mode : 0 Cool 1 Heat and
Cool 2 Heat and cool + auxiliary
elec. Heating 3 Heat default
setting: 1 Heat and Cool
Remarks:
For the XHP series ,
Mode default setting : 3. Heat
14
16

Parameter 9
Manual adjustment steps of
Cooling target for superheat
electronic expansion valve
(-15 °C -15 °C),default
setting -2 °C
HEATING MODE COOLING MODE
5. 3 How to know the current status?
Inlet water temp.
Gas return temp.
Outlet water temp.
Ambient temp.
Heating Condenser temp.
Cooling Condenser temp.
Parameter A
Manual adjustment steps
of electronic expansion
valve(18-94), default
setting: 70(*5)
15
17

Actual steps
of electronic expansion
valve.
(1) Press or to check water-in/water-out/heating and cooling Condenser /back gas/ambient
temperature/actual steps of electronic expansion valve.
(2) When the unit is switched off, current time is displayed.
5.4 Water temperature setting:
Under current mode, press or to modify the water setting temperature even if it is ON/OFF status.
5.5 Locking setting
Long press and 5 seconds to lock the parameters, Press and for 5 seconds again to unlock
4.6 Time setting:
Press to set the time, and press
or to adjust the time After pressed the again to store the new
data.
5.7 TIMER ON SETTING
Press
to set the time for HP start to run, and press or to adjust starting time.then, to press
again to store the new data.
5.8 TIMER OFF SETTING
Press to set the time for HP stop running, press or to adjust the time of stop running, then, press
again to store the new data. When liglits press to cancel the timer setting.
16
18

Parameter Meaning Range Defaul Remarks
0 To set the entering water temp under cooling mode 15 - 35 °C 28 °C Adjustable
1 To set the entering water temp under heating mode 15 - 40 °C 28 °C Adjustable
2 Entry into defrosting time period 30 - 90 min 40 min
3 Terms of Entry defrosting function -30 °C to 0 °C -7 °C
4 Terms of Exit defrosting function 2 to 30 °C 20 °C
5 Time of Entry defrosting 1 to12 min 12 min
6Mode: 0 Cool 1 Heat and Cool 2 Heat and Cool +
auxiliary elec heating 3 Heat 0 - 3 1
7 Mode selection of Electronic expansion valve 0 - 1 1
(auto)
8 Superheat for heating target -15 °C - 15 °C 3 °C
9 Superheat for cooling target -15 °C - 15 °C -2 °C
AManual adjustment steps of electronic expansion
valve 18 - 94 70
B Inlet water temperature Exact testing by
value
C Outlet water temperature -9 - 99 °C Exact testing by
value
D Condenser temperature under heating mode Exact testing by
value
E Gas return temperature Exact testing by
value
F Ambient temperature Exact testing by
value
G Condenser temperature under Cooling mode -
H Actual steps of electronic expansion valve N * 5Exact testing by
value
ATTENTION:
•HP running parameters must be checked after installation and before first used.
•When the LED on, it will display water inlet temperature.
•When the LED off, it will display the actual time
•When the LED on, the water temp could be changed.
5.9 RUNNING DATA SETTINGS
-9 - 99 °C
-9 - 99 °C
-9 - 99 °C
-9 - 99 °C
For the XHP series ,
Mode default setting :
3. Heat
17
19