Briteq BT-BUBBLEFOG User manual

Other languages can be downloaded from:
WWW.BRITEQ-LIGHTING.COM
ENGLISH
Operation Manual
Version: 1.0

ENGLISH OPERATION MANUAL
BRITEQ®1/8 BT-BUBBLEFOG
OPERATION MANUAL
Thank you for buying this BRITEQ®product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
•Powerful bubble and fog machine combination with 11 pcs of 8Watt-RGBA LED’s.
•Each effect can be used individually or combined to produce bubbles filled with fog.
•Equipped with a double fan to blow the bubbles and/or smoke meters away
•Controllable via:
•4 or 11 DMX channels
•Wireless remote control (included)
•Build-in timer
•Manual activation
•Prepared for wireless DMX: just plug-in an optional WTR-DMX DONGLE ! (Briteq®code: 4645)
•Uses regular water based Bubble Liquid and Fog Liquid
•Optional omega clamp = Briteq Omega Bracket Small (Order Code B02677)
BEFORE USE
•Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
•Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
•Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check if the carton contains the following items:
•Operating instructions
•BT-BUBBLEFOG effect machine
•Power Cable
•Wireless remote controller
SAFETY INSTRUCTIONS:
CAUTION: To reduce the risk of electric shock, do not remove the top cover.
No user-serviceable parts inside. Refer servicing to qualified service
personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use
or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.
This symbol means: indoor use only.
This symbol means: Read instructions.
This symbol determines: the minimum distance from objects. The minimum distance between fogger
output and objects must be more than 1 meter.
•To protect the environment, please try to recycle the packing material as much as possible.
•To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
CAUTION

ENGLISH OPERATION MANUAL
BRITEQ®2/8 BT-BUBBLEFOG
•To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
•This unit is for indoor use only.
•Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
•Locate the unit in a well ventilated spot, away from any flammable materials and/or liquids.
•Don’t cover any ventilation openings as this may result in overheating.
•Prevent use in dusty environments and clean the unit regularly.
•Keep the unit away from children.
•Inexperienced persons should not operate this device.
•Maximum save ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
•The units’surface temperature may reach up to 85°C. Don’t touch the housing with bare hands during its
operation.
•Make sure to always place the unit on a stable surface, never install the fogger above the audience, a little
liquid can always drip from the fog output.
•Allow the device about 10 minutes to cool down before you start servicing.
•Always unplug the unit when it is not used for a longer time or before you start servicing.
•Check that the available voltage is not higher than the one stated on the rear panel of the unit.
•The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
•Never let the power-cord come into contact with other cables!
•This unit must be earthed in order comply with safety regulations.
•In order to prevent electric shock, do not open the cover.
•Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
•In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
•The housing must be replaced if they are visibly damaged.
•Please use the original packing when the device is to be transported.
•Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
DESCRIPTION:
1. OMEGA BRACKET: this optional omega
bracket can be used to hang the unit in a
truss.
2. DISPLAY shows the various menus and the
selected functions.
3. CONTROL PANEL:
•MODE button: press several times to
navigate through the option menu
•TIMER & UP button: used to
increase the selected value. When no
dmx cable is connected, this button
will start the automatic timer working
mode
•FOG & DOWN button: used to
decrease the selected value. When
no dmx cable is connected, this
button will start the manual working
mode
•ENTER/STOP button: used to
confirm the selected value. When no
dmx cable is connected, this button
will stop the automatic timer or
manual working mode

ENGLISH OPERATION MANUAL
BRITEQ®3/8 BT-BUBBLEFOG
4. M-DMX INPUT: Please note that this USB-connector is NOT used for updates or to
connect the unit to a PC! Instead this USB-connector makes it very easy to add wireless
DMX to the unit! Just add the (optional) WTR-DMX DONGLE from BRITEQ®and you will
get wireless DMX! Moreover, you will be able to connect other DMX-controlled
equipment to the DMX-output so you can share the wireless DMX function with all
connected units! No extra settings to be made in the setup menu, just follow the
procedure in the user manual supplied with the WTR-DMX DONGLE from BRITEQ®. The
separate WTR-DMX DONGLE is available from WWW.BRITEQ-LIGHTING.COM (order
code: 4645)
5. DMX INPUT: 3-pin male connector, used to connect the fogger directly to a DMX-controller or to the
previous unit in the DMX chain.
6. DMX OUTPUT: 3-pin female connector, used to connect the fogger with the next unit in the DMX chain.
7. MAINS CONNECTOR: insert the supplied mains cable here and connect it to in a mains wall socket with
earth connection.
8. BREAKER: first locate and solve the problem that caused the breaker to be activated. When the
problem is solved, push the button to reset the breaker.
9. POWER SWITCH: used to switch the machine ON/OFF
10. BUBBLE FLUID RESERVOIR: to be filled with CE-certified bubble fluid. Make sure that the fluid
container is never empty during operation.
11. FOG FLUID RESERVOIR: to be filled with CE-certified smoke fluid. Make sure that the fog fluid
container is never empty during operation; this will damage the pump of the fogger.
MENU SETTINGS:
READY TO WORK
This message will be shown on the display as soon as the machine is ready to be used.
When the unit is just started up, the heating element of the fogger needs some time to warm up until it
reaches its ideal working temperature.
DMX512 ADDRESS
Used to set the start address when the unit in used in a DMX chain.
•Press the MENU button until DMX512 ADDRESS is shown on the display.
•Use the DOWN and UP buttons to change the DMX address.
•Once the correct address is shown on the display, press the ENTER button to confirm.
DMX512 MODE
Used to choose the DMX channel mode.
•Press the MENU button until DMX512 MODE is shown on the display.
•Use the DOWN and UP buttons to change the DMX mode (4CH or 11CH).
•Once the correct mode is shown on the display, press the ENTER button to confirm.
BUBBLE
Used to activate/deactivate the production of bubbles when the machine is used in MANUAL or
TIMER mode or wit the wireless remote controller
•Press the MENU button until BUBBLE is shown on the display.
•Use the DOWN and UP buttons to select ON (bubbles) or OFF (no bubbles).
•Once the correct mode is shown on the display, press the ENTER button to confirm.
HAZE OUTPUT
Used to set the amount of smoke that should be produced when the machine is used in MANUAL or
TIMER mode or with the wireless remote controller
•Press the MENU button until BUBBLE is shown on the display.
•Use the DOWN and UP buttons to select OFF (no fog) or a value between 1% and 100% (amount of fog).
•Once the correct mode is shown on the display, press the ENTER button to confirm.

ENGLISH OPERATION MANUAL
BRITEQ®4/8 BT-BUBBLEFOG
FAN SPEED
Used to set the speed of the fans when the machine is used in MANUAL or TIMER mode or with the
wireless remote controller. This will define how far the smoke/bubbles should be blown away.
•Press the MENU button until FAN SPEED is shown on the display.
•Use the DOWN and UP buttons to select a value between 1% (slow speed) and 100% (max speed).
•Once the correct mode is shown on the display, press the ENTER button to confirm.
REMARK: when you set the speed to 100% and Bubbles are used, the maximum speed will be
automatically reduced to the maximum speed for the use with bubbles. This is to prevent the bubbles
from being blown to pieces. When no bubbles are used, the speed will go to 100%
LED COLOR
Used to set the color that should be produced when the machine is used in MANUAL or TIMER mode
or with the wireless remote controller
•Press the MENU button until LED COLOR is shown on the display.
•Use the DOWN and UP buttons to select the desired color mode:
•OFF
•RED
•GREEN
•BLUE
•AMBER
•CYAN
•YELLOW
•PURPLE
•WHITE
•SLOW FADE
•FAST FADE
•SLOW SCROLL
•FAST SCROLL
•Once the correct mode is shown on the display, press the ENTER button to confirm.
INTERVAL SET
Used to set the interval time between each program activation
•Press the MENU button until INTERVAL SET is shown on the display.
•Use the DOWN and UP buttons to select an interval between 1 and 600 seconds.
•Once the correct interval is shown on the display, press the ENTER button to confirm.
DURATION SET
Used to set the duration of the program
•Press the MENU button until DURATION SET is shown on the display.
•Use the DOWN and UP buttons to select a duration between 2 and 255 seconds.
•Once the correct duration is shown on the display, press the ENTER button to confirm.
CLEAN MODE
Used to automatically clean the fluid tubes after each use;
WE STRONGLY ADVISE TO SWITCH THIS FUNCTION ON ;
•Press the MENU button until CLEAN MODE is shown on the display.
•Use the DOWN and UP buttons to select ON (automatic leaning activated) or OFF (automatic cleaning
deactivated).
•Once the desired mode is shown on the display, press the ENTER button to confirm.
FIRMWARE VERSION
Used to check the installed firmware version
•Press the MENU button until FIRMWARE VERSION is shown on the display.

ENGLISH OPERATION MANUAL
BRITEQ®5/8 BT-BUBBLEFOG
GENERAL OPERATING INSTRUCTIONS
IMPORTANT
The unit must always be installed so that the bottom of the unit is perfectly horizontal. The
unit must not be inclined forward, otherwise the bubble fluid will leak.
•Put the machine on a flat and very stable surface. Make sure that nobody can put their hands just in front
of the output.
•Make sure the fog liquid tank and the bubble liquid tank are not empty. Always use good quality liquid to fill
up the tanks. Close the tank immediately to prevent dirt to enter the reservoir!
•Make sure to plug the machine in a mains wall socket with earth connection
•Switch the unit on and wait for about 3 to 4 minutes if you want to use the smoke generator. (warm up
time)
•WARNING: NEVER use the machine with an empty reservoir. This can damage the pump !
WIRELESS REMOTE CONTROLLED:
First make all the desired settings manually in the menu. (see previous chapter MENU SETTINGS)
These menu options can be adapted:
•BUBBLE (on or off)
•HAZE OUTPUT (amount of fog)
•FAN SPEED
•LED COLOR
Once this is done, you can use the wireless remote controller to start the automatic program
(button on top) or to stop it (button below)
Important: don’t forget to pull out the antenna of the wireless remote controller for a better signal
transmission.
TIMER CONTROLLED:
First make all the desired settings manually in the menu. (see previous chapter MENU SETTINGS)
These menu options can be adapted:
•BUBBLE (on or off)
•HAZE OUTPUT (amount of fog)
•FAN SPEED
•LED COLOR
•INTERVAL SET
•DURATION SET
Once this is done, press the UP / TIMER button to start the automatic program
To stop the TIMER, press the ENTER / STOP button

ENGLISH OPERATION MANUAL
BRITEQ®6/8 BT-BUBBLEFOG
MANUAL CONTROL:
First make all the desired settings manually in the menu. (see previous chapter MENU SETTINGS)
These menu options can be adapted:
•BUBBLE (on or off)
•HAZE OUTPUT (amount of fog)
•FAN SPEED
•LED COLOR
Once this is done, press the DOWN / FOG button to activate the machine
To stop, press the ENTER / STOP button
DMX-OPERATION:
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Electrical installation:
•The DMX-protocol is a widely used high speed signal to control intelligent light and other equipment. You
need to “daisy chain” your DMX controller and all the connected units with a good quality balanced
cable.
•Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these
cables are compatible with balanced audio cables.
Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
Pin layout XLR-5pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) ~ Pins4+5 not used.
•To prevent strange behavior of the light effects, due to interferences, you must use a 90Ω to 120Ω
terminator at the end of the chain. Never use Y-splitter cables, this simply won’t work!
•Make sure that all units are connected to the mains.
•Each unit in the chain needs to have its proper starting address so it knows which
commands from the controller it has to decode.
WIRELESS DMX-OPERATION:
All the settings are the same as for the normal wired DMX operation. Only the DMX XLR
input connector will not be used; the signal will come in via the optional M-DMX Dongle.
Remark: The signal that is received via the wireless M-DMX Dongle will also be
transmitted to the DMX output XLR connector. This means you can still connect other units
to the BT_BUBBLEFOG via a normal DMX cable
4 CHANNEL MODE
CH
Function
Value
Details
CH 1
FOG
000-005
OFF
006-255
ON →from low volume to high volume
CH 2
BUBBLES
000-005
OFF
006-255
ON
CH 3
FAN
000-005
OFF
006-255
ON →from low speed to high speed
CH 4
COLOR
MACRO
000-015
NO color
015-024
Red
025-045
Green
046-066
Blue
067-087
Amber
088-108
Light Blue
109-129
Yellow
130-150
Purple
151-171
White
172-213
Color Fade with speed control 172=Slow to 213=Fast
214-255
Color Scroll with speed control 214=Slow to 255=Fast

ENGLISH OPERATION MANUAL
BRITEQ®7/8 BT-BUBBLEFOG
11 CHANNEL MODE
CH
Function
Value
Details
CH 1
FOG
000-005
OFF
006-255
ON →from low volume to high volume
CH 2
BUBBLES
000-005
OFF
006-255
ON
CH 3
FAN
000-005
OFF
006-255
ON →from low speed to high speed
CH 4
DIMMER
000-255
MANUAL COLOR settings
CH 5
RED
000-255
CH 6
GREEN
000-255
CH 7
BLUE
000-255
CH 8
AMBER
000-255
CH 9
STROBE
000-015
Strobe OFF
016-255
Strobe (slow to fast)
CH 10
COLOR
MACRO
000-015
NO color
015-024
Red
025-045
Green
046-066
Blue
067-087
Amber
088-108
Light Blue
109-129
Yellow
130-150
Purple
151-171
White
172-213
Color Fade with speed control 172=Slow to 213=Fast
214-255
Color Scroll with speed control 214=Slow to 255=Fast
CH 11
Bubble
Cleaning
000-005
OFF
006-255
Cleaning mode ON
OVERHEAD RIGGING
IMPORTANT
The unit must always be installed so that the bottom of the unit is perfectly horizontal. The
unit must not be inclined forward, otherwise the bubble fluid will leak.
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials should
be used, the installed device should be inspected regularly for safety.
•Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
•Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
•The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
•Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
•Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
•The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
•Don’t cover any ventilation openings as this may result in overheating.
•The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.

ENGLISH OPERATION MANUAL
BRITEQ®8/8 BT-BUBBLEFOG
MAINTENANCE
•Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
•All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
•Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
•The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
Cleaning the fogger:
To prevent obstructions in the heater, pump and tubes, the fogger should be cleaned on a regular basis:
every 100h of continuous operation is a good reference.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
This device has been designed to produce decorative effect lighting and is used in light show systems.
Mains Input: 220-240 V, 50/60 Hz
Max. Power Consumption: 850 Watt
DMX Channels: 4 & 11
Breaker: 5A/250V
Warm up time: 3 min
Max Fog Output Volume: 4.500 cfm
Tank size: 2.5 L Fog Fluid + 5L Bubble Fluid
Fog Fluid Consumption: 60 min/L @ 100%
Bubble Fluid Consumption: 40 min/L
LEDs: 11 x 8W RGBA (red-green-blue-amber)
Dimension: 455 x 400 x 450 mm
Weight: 16 kg
All the information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com