Brivis B063047 User guide

Brivis Touch Controller
Installer Manual

1
Brivis Touch Controller Kit
Scope
Please read these instructions carefully before installing this
product. This manual covers the installation of the wall mounted
Brivis Touch Controller for the following Brivis applications:
GasDuctedHeating
Gas Ducted Heating & Refrigerated Cooling (Dual Comfort)
Evaporative Cooling
Zoning, including Brivis ZonePlus
For the installation of Brivis Heating and Cooling products please
refer to the equipment Installer Manuals.
This manual is based on Australian Standards - for all other
applications, please refer to relevant local codes and regulations.
Any deviations from these instructions may, at the discretion of
Brivis, void the warranty. As a result, the customer and/or installer
may be charged a fee for non-product warranty related call outs.
Also, note that failure to comply with these instructions may
preclude Brivis from being able to service the product.
Terminology:
Shall:Indicatesamandatoryrequirementofthismanual.
Should:Indicatesarecommendedrequirementofthismanual.
Disclaimer
IMPORTANT NOTICE: This document is a guide only. Laws, regulations and industry standards can
vary between States and Territories. Accordingly, this guide must be read in conjunction with, and
subjectto,alllaws,regulationsandindustrystandardsapplicablein theState or Territoryinwhich the
products are installed. You must ensure that the installation of the products will comply with
those laws, regulations and standards, and that the products recommendedtocustomersare
fitforthepurposeforwhichtheyareintended.
Table 1: Brivis Touch Controller Kit Brivis Part No. B063047
Contents and Description Qty
Brivis Touch Controller 1
Interface Module 1
Power Transformer 1
Power & Communication Loom 1
Plug & Screw Kit (for Brivis Touch) 1
Screw (for Interface Module) 2
Screw Driver 1
Inspect the product to ensure it matches your order. In the event of
damage or incorrect delivery, notify the supplier immediately. Brivis
accepts no responsibility for installation of damaged or incorrect
product.
Please read these installation instructions before undertaking the
installation process.
Specifications subject to change without notice.
Pictures for illustration purposes only.
© Brivis Climate Systems Pty Ltd 2016
The Brivis Touch Controller is compatible with selected Brivis
units only. For information on compatibility please contact Brivis.
Pre-2010 compatible Brivis heaters will have limited on-board
diagnostics.

2
TableofContents
1.0 Home Screen – Key Functions .................................................4
2.0 Brivis Touch Controller Installation..........................................5
2.1 Location of the Brivis Touch.....................................................5
2.2 Location of the Interface Module..............................................6
2.3 Install the Brivis Touch .............................................................6
2.5 Install Interface Module.............................................................7
2.6 Connection of Interface Module to P&C Loom ........................8
2.7 Connection of Interface Module to Appliance..........................9
3.0 System Setup.............................................................................9
3.1 Turning the System ON.............................................................9
3.2 Set Day/Time............................................................................10
3.3 Installer Setup..........................................................................11
3.4 Reset Networker ID..................................................................12
3.5 Networker Parameters.............................................................13
3.6 Cooler Parameters...................................................................13
3.7 Heater Parameters...................................................................13
3.8 System with no Zones.............................................................13
3.9 System with Zones (Inc. Brivis ZonePlus) ............................. 14
3.10 System Operation..................................................................14
3.11 Service Notification Message ...............................................14
3.12 Outdoor Temperature Sensor (Optional)..............................15
4.0 Product and Warranty Registration ........................................15
5.0 Instruct Home Owner on System Operation...........................15
6.0 Troubleshooting.......................................................................16
6.1 Power Outages.........................................................................16
7.0 Appendix ..................................................................................17

3
Definitions
Brivis Networker
Networker is a term used for a temperature sensing or
communicating device which communicates over two-wire bus.
There can be only one Master Networker (n01), all others must be
slaves (n02, n03 ….n10).
Brivis Touch Controller
Primary user interface with touchscreen display. Where multiple
Brivis Touch Controllers are installed, the “Master” Brivis Touch
Controller can be identified by the letter “M” displayed in the
bottom right hand corner of the screen. The Master has default
sensor identification “n01”.
The Brivis Touch Controller is a touchscreen thermostat which
communicates over two-wire bus. It is compatible with NC-3, NC-6
and N-T1 sensors.
Brivis NC-6 Networker Controller
A user interface with LCD display. The NC-6 has default sensor
identification “n01 ID00:1” (Master) and should be changed to a
slave if used on the same system as the Brivis Touch Controller.
Brivis NT-1 Remote Temperature Sensor
Zone temperature sensor with an LED that blinks during
communication with Master Brivis Touch Controller. Default NT-1
sensor identification is “n02”. Additional Brivis Touch Controllers
can be used in place of up to 3x NT-1 sensors. The NT-1 sensor
can also be used as the outdoor temperature sensing device.
Zone
One room or a group of rooms; normally selected on the basis of
usage or that have similar heating or cooling needs.
ControlledZone
A zone that is separately controlled by its own zone sensor and
zone damper. There are as many zone sensors in the home
comfort system as there are Controlled Zones.
CommonZone
A zone that is not separately controlled by its own sensor and zone
damper. It operates whenever heating or air conditioning is on,
regardless of the status of any controlled zones.
Constant Zone
A predetermined zone, typically the largest and containing the
return air grille, is designated as the Constant Zone. The Constant
Zone functions as a Common Zone only during refrigerated cooling
mode to ensure the minimum cooling airflow requirements are met.
MultiTemperatureSetPoint(MTSP)System
The zone temperature set point can be set independently across
all Touchscreens and/or Temperature Sensors.
Single Temperature Set Point (STSP) System
The zone temperature set point is the same across all
Touchscreens and/or Temperature Sensors.

4
1.0 Home Screen – Key Functions
Diagram 3
:
Evaporative Cooling Home Screen
Manual or Schedule
Operation
* Active
with MTSP & STSP
systems only
D
iagram 1:
Heating Home Screen
Flame
Symbol
Power
Zones Where
Fitted
*
Mode Indicator
Adjust Set
Temperature
Indoor
Temperature
Fan Status
Indicator
Day
Digital
Clock
M - Master
Controller
System Mode
(HEAT/COOL/EVAP)
Menu – Display
Options or Settings
Fan Select
Mode
Diagram 2:
Add-On Home Screen

5
2.0 Brivis Touch Controller Installation
The Brivis Touch Controller is connected to a compatible Brivis
appliance through the Interface Module. A 20m, four core, Power
& Communication Loom (P&C Loom),connects the Brivis
Touch Controller to the Interface Module. The Power
Transformer (12VDC) supplies power to the Interface Module.
Diagram 4: Connection Diagram
To connect the Brivis appliance to the Brivis Touch:
1. Determine location of the Brivis Touch.
2. Determine location of the Interface Module.
3. Install the Brivis Touch.
4. Install Interface Module.
5. Connect Interface Module to Appliance.
2.1 Location of the Brivis Touch
For proper operation the Brivis Touch must accurately monitor the
temperature in the space it controls.
Guidelines:
The Brivis Touch should be mounted:
Approximately 1.5m above floor level (ensure hole into wall
cavity is properly sealed).
Close to the centre of the living space on an internal wall.
On a section of wall that does not contain pipes, electrical wires,
antenna cables or ductwork.
The Brivis Touch should NOT be mounted:
Where it is exposed to direct sunlight or other heat sources
which may cause a false reading.
Near or in the path of supply air outlets or return air grilles.
On outside walls, near windows or doors leading to outside.
In areas with poor air circulation such as recesses or behind
doors.
Note:
Do not install the wiring with the power turned on, as the
fuse may blow, which
is
not be covered under warranty.
Note:
When there are multiple Brivis Touch Controllers on a
system, always ensure that the location of each is within 20m
of the Interface Module
Power & Communication
Loom, 20m (supplied)
0.75mm² figure-8 cable
(field supplied)
Appliance
(field supplied)
Power Transformer
12VDC 1.5m loom
(supplied)
Brivis
Touch
(supplied)
TW2
TW1
Interface
Module
(supplied)
Isolation
Switch
(field supplied
GPO)

6
2.2 Location of the Interface Module
The Interface Module shall be located within 1.5m of a 10 Amp
240 volt fixed switched socket outlet. The Brivis Touch shall be
within 20m of the Interface Module.
2.3 Install the Brivis Touch
The Brivis Touch Backing Plate must be installed prior to
mounting the Brivis Touch.
To mount the Backing Plate do the following:
1. Remove the Brivis Touch Backing Plate from the packaging.
2. Use Backing Plate as a template and mark the two Mounting
Hole centres and the Loom Access hole centre, refer to
Diagram 5.
3. Install the supplied wall Plug Kit in the Mounting Hole
locations. For drill sizes refer to Diagram 5.
4. Fasten Backing Plate with wall Plug Kit screws.
Diagram 5: Brivis Touch “Backing Plate”
To mount the “Brivis Touch”:
1. Run the supplied P&C Loom from the Touch to the
Interface Module.
2. Draw the loom from the wall cavity and feed through the
P&C Loom Access opening on the Touch Backing
Plate.
3. Connect the P&C Loom terminal (female) to the Touch
terminal (male) before mounting it on the wall, refer to
Diagram 6.
4. Push excess cable back into the wall cavity and mount
Touch onto the Backing Plate. The three Male Clips on
the Backing Plate will engage and secure the Touch,
refer to Diagram 7.
Diagram 6: Brivis Touch Controller P&C Loom Connection
Mounting Hole
Drill size
ø
6.0mm
Mounting Hole
Drill size ø6.0mm
P&C
Loom
Access
Drill size ø13
2
3
1

7
Diagram 7: Mounting Brivis Touch to Backing Plate 2.5 Install Interface Module
The Interface Module facilitates communication between the
Brivis Touch and the Brivis appliance(s) through the P&C Loom,
and is capable of connecting up to four Brivis Touch units.
The Interface Module requires a 12VDC power supply from the
Power Transformer.
The Interface Module also has an “Isolation Switch”; a red
“Status L.E.D” indicates it is ON, refer to Diagram 8.
Diagram 8:Mounting Interface Module Power & Communication
Loom Connection,
(Any of the four ports)
Transformer
connection
Isolation
switch
Status
L.E.D
2-wire bus
connection
TW1
TW2 TW1
TW2
Male Clips

8
To install the Interface Module:
1. Position in an environmentally protected area where the
temperature does not exceed 70°C.
2. Locate within 1.5m of a 10 Amp 240 volt fixed switched socket
outlet.
3. Distance from Interface Module to Brivis Touch shall be no
more than 20m.
4. Mount with supplied screws as shown in Diagram 9.
Diagram 9: Mounting Interface Module on flat surface
2.6 Connection of Interface Module to P&C Loom
The Interface Module is capable of connecting up to four
Brivis Touch Controllers. The P&C Loom can be connected
to the Interface Module through any of the four ports, refer to
Diagram 10.
Diagram 10: Connection of Interface Module to P&C Loom

9
2.7 Connection of Interface Module to Appliance
The Interface Module has four terminal points for the
connection of the Brivis Appliance control wires TW1 &
TW2. When connecting to an appliance, use only the first
set (Set 1) of two terminals or the second set (Set 2).
Never use a mixed combination of terminals when
connecting to a single appliance. For example, a Brivis
Touch operating a Brivis Evaporative Cooler and a Brivis
Gas Heater may have the two right terminals connected
to the Heater (SET 1) and the two left terminals connected
to the Evaporative Cooler (SET 2), refer to Diagram 11.
Diagram 11: Connection of Interface Module to Appliance
For more information regarding appliance connection please
refer to the product installation manual supplied with the
appliance.
3.0 System Setup
3.1 Turning the System ON
Once the system is fully connected, it can now be turned ON in the
following sequence:
1. Mains power to heater 516 Zone Module (if connected).
2. Mains power to Heater / Evaporative Cooler / Refrigeration
appliance(s).
3. Mains power to Interface Module.
Press isolation switch on Interface Module (L.E.D on).
Once completed the Brivis Touch Controller will power up and you
will be prompted to enter the day and time.
Note:
When there is more than one Brivis appliance connected to
the Interface Module ensure that the TW1 & TW2 polarity is
correct at both ends of the 2
-
wire bus cable.
Note:
Do not install any wiring with the power turned on, as the
fuse may blow, which would not be covered under warranty.
TW1
TW
2
TW1
TW
2
To Heater
To Evaporative
Cooler
SET 2
SET 1
Note
: Once you access the MENU Screen and select a
configuration option, if no button is pressed for 60 seconds while
in that configuration screen, the Touch will exit the configuration
mode and return to normal operation; this applies to all options
other than SCHEDULE.