Eliweli EW-601 User manual

《EW-601 Instruction for use 》
Micro computer humidity controller series
Code: 601H. 12.08.03
Ewic-601
1. Operating voltage ：AC220V 土10% 50HZ/60HZ
2. Load current ：Alarm relay5A/220V/AC
Control plus / Dehumidification relay10A/220V/AC
3. Controlled output ：a group control adds/dehumidifies,
a group control warning
4. Control range ：5%RH~95%RH、Does not have the condensation
5. Power consumption ：≤3W
6. Controls the wet precision ： ±5% Resolution：±1%RH
7. Working environment ：0℃～60℃ 10%～90%RH
Does not have the condensation,the standard length 2 m
8. Overall dimension ：76（length）×35（wide） ×76（high）mm
9. Starter size ：71（length） ×29（wide）mm
EW-601
First thanks you to use this company measuring appliance
product. This product union widespread automatic control tech-
nology, the simplicity of operator, controls the warm precision to
be high, antijamming ability. Applies in equipment's and so on
air the constant humidity doctor humidity controls and the demo-
nstration (adds wet and dehumidifies dual purpose control model).
This product uses the import the humidity sensor, the survey
humidity is accurate, is stable, and the bringing humidity sensor
makes a mistake the self-checking function; Dew-point output
alarm function; Power failure automatic memory function.
D
Pt
1~20%
0~3
3
0~15
5%
0
H/P H/P
CA -10%~10% 0
CP 0~30 6
H
- - this product avoids using easily to have the dew-point situation.
for example: 1st, airtight, the space small indoor environment (for example cold storage) will
cause the relative humidity to be unusual.
2, thermal shock's environment (for example use forced-air cooling system) will
cause the relative humidity to be unusual.
Brief on Operation
Demonstration now humidity value
Loud power LED
Technical Specifications
Parameters for Procedure
Function
Indicator Setting range Ex-factory
value
Adds wet/dehumidifies
Dew point time delay
The humidity returns to
the difference
Delay time
Humidity Adjustment
Humidity Delay Change
Unit
Min
－
RH
RH
Min
Wiring diagram
/
AP
C/V C/V C
S e c
Condensation Way
红
色
连
线
黑
色
连
线
白
色
连
线
Humidity sensor
123 12365 9
11
12
8
Mode：EW-601H
710 4
220V/AC
Output Load:
220V/AC
Control
humidifier
Warning
output
Warning
output
White
Black
Red
5A 10A
Adds wet or
exsiccator
13

Time delay hypothesis：
enters the menu according to the key, or the key
transfers to according to the key , presses the
key not to put again demonstrated that the original setup
param-eter (this function is according to humidifier whether
to need time delay work, but establishes 0~3 minutes freely).
Temperature correction:
enters the menu according to the key, or the
key transfers to according to the key , does not
put according to the key, demons trated that the
original setup parameter, may or the key readjusts
the parameter according to the key to carry on the
adjustment (this function be when humidity and surv-
ey demonstration value has error carries on
adjustment).
The operation showed
注意事项
The hypothesis controls the wet parameter:
The measuring appliance circular telegram demonstrated
the value is the humidity value which present surveys, when
establishes humidity value which needs, according to the
key is the demonstration preinstall humidity setting value, pre-
sses setting value which the key or the key may the
resume load need, after revising the parameter, does not need to
press any key to confirm, six seconds later automatic memory
new setup parameter.
Enters the menu according to the key namely the
demonstration the code, the key or the key may
circulate the menu according to :
Adds wet and dehumidifies the control model：
A according to the key or the key to enter the menu,
demonstrated that the code, according to the key,
presses the key again either the key choice or
(adds wet or dehumidifies function).
Hypothesis dew point time delay：
enters the menu according to the key, or the key
transfers to according to the key , according to
the key, presses the key again or the key may change
the dew point time delay the setting value (this function is when
the humidity sensor induces after the dew point, time delay
demonstration , output alarm, but establishes 0~30
minutes freely).
The hypothesis humidity returns to the difference：
enters the menu according to the key, or the key
transfers to according to the key , does not put
according to the key, demonstrated that the original setup
parameter, this time or the key may readjust the parameter
after the key (this function is when achieves humidity
stop, according to returns to difference parameter which establ-
ishes to add wet).
Time delay hypothesis：
enters the menu according to the key, or the key
transfers to according to the key , presses the key
—
Warnings
1. Please read this product instruction carefully and connect
input/output plugs of power & sensor to the corresponding
sockets strictly by following connection diagram, otherwise
the usage & operations will be affected. Check again to make
sure there is no mistake. Tighten all the screw of connection
plugs aga in, and then connect it to the power for running.
2. Keep away this product from moist or corrosiIve air and
high magnetic field. Otherwise the normal operaton of this
product will be affected.
3. All our products have passed strict quality inspections
before leaving factory. We provide one-year quality guarantee
(which is limited to product itself) period for this product.
If you have any doubt or problem concerning the electronic
temperature or humidity controller made by us, please contact
our distributors and we will provide you high-quality after-
sale services. Thanks!
Guangzhou Eliweli Autocontrol Tech. Co., Ltd
——
——
While the digital tube show flash E1 ,the sensor will shorted or
open and the alarm system relay is working.
While the Condensation ,such as
show flase E2 before the sensor Condensation will be delay
and the alarm system relay is working.
way choice C digital tube
Enter the menu,press set or set to ,press key,
while press key or key can choice c or v way
(condensing or non-condensing).
when choice c way,the humidity sensor sensitive to the dew
point delay show E2 and output alarm,when choice V way,show
99%(Not alarm).
Condensation way:
Modify the parameters don’t need press any key. Confirm six
seconds automatic memory the new set parameter.
Humidification Mode:
below the set-----Back to the start humidification
setting the value higher or will equal stop humidification
setting the value lower will equal or stop dehumidificationt
Dehumidification Mode:
higher the set-------Back to the star dehumidificationt
Functional Description not to put again demonstrated that the original setup param-eter
(this function is according to humidifier whether to need time
delay work, but establishes 0~3 minutes freely).

Time delay hypothesis：
enters the menu according to the key, or the key
transfers to according to the key , presses the
key not to put again demonstrated that the original setup
param-eter (this function is according to humidifier whether
to need time delay work, but establishes 0~3 minutes freely).
Temperature correction:
enters the menu according to the key, or the
key transfers to according to the key , does not
put according to the key, demons trated that the
original setup parameter, may or the key readjusts
the parameter according to the key to carry on the
adjustment (this function be when humidity and surv-
ey demonstration value has error carries on
adjustment).
The operation showed
注意事项
The hypothesis controls the wet parameter:
The measuring appliance circular telegram demonstrated
the value is the humidity value which present surveys, when
establishes humidity value which needs, according to the
key is the demonstration preinstall humidity setting value, pre-
sses setting value which the key or the key may the
resume load need, after revising the parameter, does not need to
press any key to confirm, six seconds later automatic memory
new setup parameter.
Enters the menu according to the key namely the
demonstration the code, the key or the key may
circulate the menu according to :
Adds wet and dehumidifies the control model：
A according to the key or the key to enter the menu,
demonstrated that the code, according to the key,
presses the key again either the key choice or
(adds wet or dehumidifies function).
Hypothesis dew point time delay：
enters the menu according to the key, or the key
transfers to according to the key , according to
the key, presses the key again or the key may change
the dew point time delay the setting value (this function is when
the humidity sensor induces after the dew point, time delay
demonstration , output alarm, but establishes 0~30
minutes freely).
The hypothesis humidity returns to the difference：
enters the menu according to the key, or the key
transfers to according to the key , does not put
according to the key, demonstrated that the original setup
parameter, this time or the key may readjust the parameter
after the key (this function is when achieves humidity
stop, according to returns to difference parameter which establ-
ishes to add wet).
Time delay hypothesis：
enters the menu according to the key, or the key
transfers to according to the key , presses the key
—
Warnings
1. Please read this product instruction carefully and connect
input/output plugs of power & sensor to the corresponding
sockets strictly by following connection diagram, otherwise
the usage & operations will be affected. Check again to make
sure there is no mistake. Tighten all the screw of connection
plugs aga in, and then connect it to the power for running.
2. Keep away this product from moist or corrosiIve air and
high magnetic field. Otherwise the normal operaton of this
product will be affected.
3. All our products have passed strict quality inspections
before leaving factory. We provide one-year quality guarantee
(which is limited to product itself) period for this product.
If you have any doubt or problem concerning the electronic
temperature or humidity controller made by us, please contact
our distributors and we will provide you high-quality after-
sale services. Thanks!
Guangzhou Eliweli Autocontrol Tech. Co., Ltd
——
——
While the digital tube show flash E1 ,the sensor will shorted or
open and the alarm system relay is working.
While the Condensation ,such as
show flase E2 before the sensor Condensation will be delay
and the alarm system relay is working.
way choice C digital tube
Enter the menu,press set or set to ,press key,
while press key or key can choice c or v way
(condensing or non-condensing).
when choice c way,the humidity sensor sensitive to the dew
point delay show E2 and output alarm,when choice V way,show
99%(Not alarm).
Condensation way:
Modify the parameters don’t need press any key. Confirm six
seconds automatic memory the new set parameter.
Humidification Mode:
below the set-----Back to the start humidification
setting the value higher or will equal stop humidification
setting the value lower will equal or stop dehumidificationt
Dehumidification Mode:
higher the set-------Back to the star dehumidificationt
Functional Description not to put again demonstrated that the original setup param-eter
(this function is according to humidifier whether to need time
delay work, but establishes 0~3 minutes freely).