Bromic Heating WATERBOY Vortex 7575150 User manual

Vortex Submersible Pump - 7575150
Operation Manual
Congratulations on your purchase of your Bromic Waterboy
submersible Vortex sump pump.
This manual contains essential information on the installation,
operation and maintenance of the pump. Please read it thoroughly
and follow these instructions in order to install and use the pump
correctly. Failure to follow these instructions may result in motor
overcharging and other malfunctions. Bromic is not liable should
instructions not have been followed.
Specification
1. Maximum operating depth 5m below water level;
2. Continuous duty when fluid temperature under +40°C;
3. Value of PH in fluid 4~10;
4. Maximum kinematic viscosity: 7xl0-7 ~23x10-6m2/s;
5. Maximum density: l.2xIO3kg/m3
Technical data (the data will be some change under
dierent voltage and frequency)
Part View
Circuit Diagram
Performance Curve
12/2022 - V1.5
220-240/50
0.34
7575150 40,32,25 133 715 9 20.5X20.0X37.5
Model
Power
Input
(kw)
Discharge
(mm)
Voltage
(V/Hz)
Max
Flow
(l/min)
Max
Head
(m)
Max.
Suspended
solid (l/min)
Weight
(kg)
Packing
(cm)
7575150 Instruction Manual - 2022.indd 17575150 Instruction Manual - 2022.indd 1 21/12/2022 2:52:21 PM21/12/2022 2:52:21 PM

Installation Guidelines
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.
1. Before installation, carefully check whether there is physical
damage on any part of the pump including electrical cable and
plug. Contact the seller if damage is found.
2. Ensure the pump is disconnected from the power source
before installing
3. Ensure the site’s power supply meets requirement as stated on
the rating label. Pump must be earthed.
4. Ensure fittings and joints are watertight.
5. Tie a rope on the handle to move the pump up and down.
Never drag the electrical cable as it may cause electrical
hazard.
6. The power supply connected to the pump must be protected
by RCD or other protective device according to Australian
standard and regulations.
7. Do not touch or move the pump before disconnecting it from
the power supply.
8. Ensure all electrical connection is away from water or area
subject to flooding.
9. If the pump is idle for a long period of time, it must be
removed, cleaned and stored in a dry&cool place.
10. The pump must be installed by qualified technician.
Notes:
• The maximum total head of the pump is 7m
• Pollution of the liquid could occur due to leakage of lubricants
• A protective device (RCD) must be installed with pump
(residual operating current <30mA)
Warnings
Danger: Keep the pump equipment away from children.
Danger: Do not operate the pump in locations classified as
hazardous.
Warning: The pump is designed to handle soft particles no
larger than 15mm in diameter. Larger particles may cause
permanent damage.
Warning: The pump is designed for water only, used on
chemicals or corrosive liquid will damage the pump and void
warranty.
Warning: Do not use the pump for liquid exceeding 40°C.
Warning: Never run the pump dry, dry operation will
permanently damage the pump and void the warranty
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard
The pump must not be used when people are in the water
The pump must be supplied through a residual current device
(RCD) having a rated residual operating current not exceeding
30mA
Disconnect the pump from the supply mains before carrying
out user maintenance such as cleaning the filter
Warranty
Please visit our webpage for warranty details-
(https://bromicgroup.com/warranty-information/)
Read all relevant documentation before operating the pump.
Failure to follow instructions may result in warranty being
voided
Troubleshooting
BROMIC Pty Ltd
10 Phiney Place, Ingleburn, NSW 2565 Australia
AU 1300 276 642 NZ 0508 276 642 [e-mail] Wbromicplumbing.com
!
!
!
!
!
!
!
!
!
!
12/2022 - V1.5
Fault Possible Cause Solutions
The motor does not start No or incorrect power supply Ensure power supply is as per rating label
The motor does not start Fuse or thermal relay disconnected Consult service provider
Flow is insucient Water inlet blocked Remove blockage
Flow is insucient Total manometric head higher than expected Verify geometric head and reposition
Flow is insucient Discharge pipe not joined properly Check the joint, ensure there is no leak
Flow is insucient Source water level is low Reposition pump or stop pumping
Flow is insucient Impeller is worn out or blocked Try to remove the blockage or contact
dealer
Others Consult service provider
7575150 Instruction Manual - 2022.indd 27575150 Instruction Manual - 2022.indd 2 21/12/2022 2:52:22 PM21/12/2022 2:52:22 PM