Direct current symbol.
This symbol signifies that this is a wireless device powered by Bluetooth®
technology. The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc., used under license.
This symbol signifies that the product must not be discarded as household waste, and
should be delivered to an appropriate collection facility for recycling. Proper disposal
and recycling helps protect natural resources, human health and the environment.
This symbol signifies and declares that this equipment complies with battery charging
which complies with California CEC and energy efficiency.
FCC Information
This device complies with Part 15 of the FCC Rules.
Caution: Any changes or modifications not expressly approved could void the user's authority
to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Warranty Information
90-Day Limited Warranty
Territory: United States/Canada
LIMITED WARRANTY TO ORIGINAL CONSUMER
This product as supplied and distributed new by an authorized retailer is warranted by Southern
Telecom, Inc. to the original consumer purchaser against defects in materials and workman-
ship (“Warranty”) as follows:
To obtain warranty service:
• Visit our customer support portal: www.customersupport123.com and select ”Support”.
• Select the brand, fill out the corresponding form (exchanges require dated proof of purchase
from an authorized retailer) then submit your request.
Your product will be repaired or replaced, at our option, for the same or similar model of equal
value if examination by the service center determines this product is defective. Products
received damaged as a result of shipping will require you to file a claim with the carrier.
Warranty service not provided
This warranty does not cover damage resulting from accident, misuse, abuse, improper
installation or operation, lack of reasonable care, unauthorized modification including software
modifications such as the installation of custom firmware. This warranty is voided in the event
any unauthorized person opens, alters or repairs this product. All products being returned to
the authorized service center for repair must be suitably packaged.
LITHIUM POLYMER BATTERY WARNINGS
This device contains a non-removable Lithium-Polymer battery. The
battery must be recycled or disposed of properly. Contact your local
waste management office for information on battery recycling or
disposal.
Rating Label Definitions
Installing the Device Holder Mount
1. Choose a location in your shower for the device holder.
Ideally, the location will be away from the spray of water,
to keep your device the most safe and dry.
Note: the adhesive mount can only be mounted once,
so please be sure of your location before mounting.
2. Peel the plastic off the back of the device holder mount to
reveal the adhesive.
3. Press the mount adhesive onto the desired surface. Press
and hold into place for 1 minute to allow the adhesive to
bind.
Installing your Device
1. Press on the top of the holder, and pull apart to open, as
shown in the image at right.
2. Place your device in the holder with the screen facing
forward.
3. Snap the device closed.
4. Slide the device holder onto the device holder mount that
you mounted in the above step.
Note: The device holder is splash-resistant. It is NOT
waterproof. Do not submerge in water. To keep your
device the most safe and dry, keep away from constantly
streaming jets of water.
Using Together
To use the speaker and device holder together, pair your device to the speaker via Bluetooth,
then install your device in the holder. You can listen to music or watch video in the shower.
1
2
1
7
8
2
