BROSTREND A3 User manual
Model: A3
AX3000 WiFi 6 Wireless Access Point
Quick Installation Guide
support@brostrend.com
Video Installation Guide is available via this link:
https://www.brostrend.com/pages/video-guide
WPS RESET
LED indicator
Gigabit Ethernet port:
For connecting with your
wired Internet.
Reset button
WPS button
Working Mode 1: Setupasa Wireless Access Point
We here set up on a mobile phone as an example. Actual setup steps on a desktop or tablet could be slightly different.
WPS RESET
WPS RESET
Ethernet cable
Note:
* The LED indicator lighting solid blue indicates a successful Internet connection. Otherwise, refer
to Q2 in FAQ to reset this access point and try again.
Ethernet (LAN)
Internet Enabled
Ethernet Port
or
WPS RESET
Plug the access point into
a power outlet.
Wait until the LED indicator
blinks red slowly.
LED indicator blinks red slowly
Power on
1
Connect the access point to an Internet-enabled Ethernet port or LAN port of your
router with an Ethernet cable. Setup completed!
Connect to the Internet
3
* If the Web UI is inaccessible,
refer to Q1 in FAQ.
2. Start a Web browser and visit
brostrendwifi.com or
192.168.0.254 in the
address bar.
Create Your Wireless Access Point Network
2
1. Connect your WiFi device to the
default WiFi network of this
access point: BrosTrend_EXT,
or connect your computer to
the Ethernet port of this access
point with an Ethernet cable.
XXXXX
WLAN
BrosTrend_EXT
brostrendwifi.com
For network security, please set a login password
for logging in to the web UI.
Set up Login Password
Login Password
Confirm Password
3. Create a login password for future
logins. (Recommended)
4. Select AP Mode, click Next.
Working Mode
Please choose the working mode based on your scenario.
Extend the coverage of the existing WiFi network.
Extender Mode
Next
Convert the existing wired network to a WiFi network
AP Mode
5. Customize the WiFi name and WiFi password,
click Save, then wait for about one minute
until the LED light blinks red slowly.
Working Mode 2: Set Up asa WiFi Extender
* This method is applicable if your router has a WPS button. Otherwise, use Method 1.
Extended Network Names:
XXXXXX_EXT or XXXXXX_5GEXT
(XXXXXX: the WiFi name of your router)
Password:
The same as the WiFi password of your existing router.
1. Power on: Plug the extender into a power outlet in the same room as your existing router. Wait until the LED indicator blinks red.
2. Press the WPS button on your router.
3. Within 2 minutes, press the WPS button on the extender, the LED indicator on extender will start to blink blue fast.
4. Wait until the LED indicator turns solid on, which indicates a successful connection with your router.
Set up via WPS button
Method 2:
Plug the extender into a power outlet
near the router.
Wait until the LED indicator blinks
red slowly.
WPS RESET
LED indicator blinks red slowly
Power on
1
For optimal performance, please plug the extender into an electrical
outlet halfway between your WiFi router and the WiFi dead zone.
The extender must be placed within the range of your WiFi router.
Keep your extender away from electronics with strong interference,
such as microwave oven, induction cooker, and refrigerator.
Relocate
3
Solid Blue: Strong signal
Solid Yellow: Good signal
Solid Red: Weak signal
Router Devices
Halfway
WPS RESET
WPS
WPS
Press
For network security, please set a login password
for logging in to the web UI.
Set up Login Password
Login Password
Confirm Password
3. Create a login password for future logins.
(Recommended)
Next
* If the Web UI is inaccessible, refer to Q1 in FAQ.
2. Start a Web browser and visit
brostrendwifi.com or 192.168.0.254
in the address bar.
Connect to Your Existing WiFi Network
2
1. Connect your WiFi device to the
default WiFi network of the extender:
BrosTrend_EXT, or connect your
computer to the Ethernet port of the
extender with an Ethernet cable.
Set up via Web Management InterfaceMethod 1:
XXXXX
WLAN
BrosTrend_EXT
brostrendwifi.com
4. Select Extender Mode,click Next.
Working Mode
Please choose the working mode based on your scenario.
Extend the coverage of the existing WiFi network.
Extender Mode
Next
Convert the existing wired network to a WiFi network.
AP Mode
5. Choose the WiFi network you want to
extend and enter the WiFi password.
7. Check if the extender connects to your WiFi network successfully according to the
status of the LED indicator.
Solid blue: Strong signal
Solid yellow: Good signal. Recommended
to move the extender closer to the router
Solid red: Weak signal. Please move the
extender closer to the router for better
performance
Blinking red: Extension failed.
Please connect to the WiFi
network of the extender
(BrosTrend_EXT) and set up again
LED indicator lighting solid on indicates a successful extension. You can connect to the following WiFi
network to access the Internet.
LED indicator blinking red indicates the extension failed. Please connect to the following network to
extend again.
2.4GHz WiFi Name: My_Home_WiFi_EXT
2.4GHz WiFi Password: XXXXXXXX
5GHz WiFi Name: My_Home_WiFi_5GEXT
5GHz WiFi Password: XXXXXXXX
WiFi Name: BrosTrend_EXT
Internet Settings
Please choose the WiFi network you want to extend.
My_Home_WiFi 5G
WiFi password
Cancel OK
6. Customize the extended WiFi name(SSID)
and password. Click Extend.
Internet Settings
Upstream WiFi Name
My_Home_WiFi
2.4GHz Extended WiFi Name
My_Home_WiFi_EXT
2.4GHz Extended WiFi Password
5GHz Extended WiFi Name
My_Home_WiFi_5GEXT
5GHz Extended WiFi Password
Same as the upstream WiFi password
Same as the upstream WiFi password
Solid Blue:
This device is set up successfully
and working normally.
Solid Red:
This device is starting up. Please
do NOT power off the device
during the process, otherwise
the device may be damaged.
Blinking Red Slowly:
The device is powered on, while
it is not connected to the Internet.
Please set up the device by
following the steps in Working
Mode 1: Set Up as a Wireless
Access Point.
Solid Blue:
This device is receiving a strong signal from your router.
Solid Yellow:
This device is receiving a good signal from your router.
Solid Red:
This device is receiving a weak signal from your router. Please
relocate it closer to your router for better performance.
Blinking Red Slowly:
The device is powered on, while the setup is not completed
or fails to receive any signal from your router. Please relocate
it closer to your router or set it up again.
Blinking Blue fast:
The device is pairing with your existing router via WPS method.
Please wait until the pairing completes.
In AP Mode In Extender Mode
Save
WiFi Settings
5GHz WiFi Name
BrosTrend_5G
5GHz WiFi Password
5G
2.4GHz WiFi Name
BrosTrend_2.4G
2.4GHz WiFi Password
2.4G
* After the WPS pairing, for network security, please connect your wireless device to the newly extended networks
and visit www.brostrendwifi.com on a browser to set up a login password for your newly extended networks.
Otherwise, the Web UI will be open to any devices connected to the extended networks.
NextNot now
NextNot now
FAQ
Q1: I cannot log into the Web Ul of the access point.
What should I do?
For initial setup, ensure your wireless device is connected to the default
network of the access point: BrosTrend_EXT.Ensure that the Mobile
Data(if any) function is disabled. lf BrosTrend_EXT is not found, please
refer to Q2 to reset the access point back to its default factory setting.
If you have set up the access point successfully, you need to connect your
device to the newly created network of this access point before logging into
the Web UI.
Verify that brostrendwifi.com is correctly entered in the address bar of your
browser. Do not visit 192.168.0.254 if the access point is already set up.
Use another web browser and try again.
Q2: How to reset the access point back to factory default setting?
With the access point fully powered on, press the RESET button with a needle-like
object, the LED indicator starts blinking yellow fast.
Wait until the LED indicator blinks red slowly, indicating the access point is
reset successfully.
Q4: What should I do if I forgot my login password?
Please refer to Q2 to reset the access point first. Then connect to the default
network BrosTrend_EXT and visit brostrendwifi.com to create a new login
password. Please note down your login password for future logins.
Q5: The extender cannot find the WiFi network of my router.
What should I do?
Ensure the WiFi network of your router can be detected by other wireless
devices.
Change the WiFi channel of your router and try again.
Change the encryption type of the router to WPA-PSK/WPA2-PSK
or WPA2-PSK/WPA3-SAE, and try again.
together with your on-line order number. We will reply to you within 24 hours.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turnind the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device is restricted to be used in the indoor.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the device and your body.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE:
(1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
(2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
IC RSS warning
Industry Canada(RSS-Gen Issue 4)
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l'intérieur afin de réduire les risques de brouillage préiudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage;
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou
émetteur.
Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le
radiateur et votre corps.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la
conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la
conformité de rf.
Operating Temperature: 0°C - 40°C
Operating Humidity: (10% - 90%) RH, non-condensing
Alimentador de Energía:
Alimentación:
Salida:
Producto
PAIS DE ORIGEN: CHINA
NOMBRE DEL PRODUCTO: Punto de acceso inalámbrico
MODELO: A3
LA OPERACIóN DE ESTE DISPOSITIVO ESTA SUJETA A LAS SIGUIENTES CONDICIONES:
a) Es posible que este equipo o dispositivo no cause interferencia perjudicial.
b) Este equipo o dispositivo debe aceptar cualquier tipo de interferencia, incluyendo la que pueda
causar su operación no deseada.
Estimado usuario: Antes de utilizar este producto lo invitamos a leer el siguiente manual para que
conozca todas sus funciones y caracteristicas.
GNU General Public License Notice
This product includes software code developed by third parties,including software code subject to the
GNU General Public License ( “GPL” ).For GPL inquiries, please contact us at support@brostrend.com
or 8 The Green,Suite A, Dover City, DE,U.S.A., Zip code 19901.Additionally, BrosTrend provides for
a GPL-Code-Center under https://brostrend.me/gpl where machine readable copies of the GPL source
codes used in BrosTrend products are available for free to download. Please note, that the GPL-Code-Center
is only provided as a courtesy to BrosTrend’s customer but may neither offer a full set of source codes used in
all products nor always provide for the latest or actual version of such source codes.
The GPL Code used in these products is distributed WITHOUT ANY WARRANTY and is subject to the
copyrights of one or more authors.
Please refer to the following GNU Public License for further information.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989,1991 Free Software Foundation, Inc.
51 Franklin Street,Fifth Floor,Boston, MA 02110-1301,USA
Everyone is permitted to copy and distribute verbatim copies
of this license document,but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it.By contrast,
the GNU General Public License is intended to guarantee your freedom to share and change free software--
to make sure the software is free for all its users.This General Public License applies to most of the Free
Software Foundation's software and to any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it
to your programs, too.
When we speak of free software, we are referring to freedom,not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this
service if you wish),that you receive source code or can get it if you want it,that you can change the software
or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights,we need to make restrictions that forbid anyone to deny you these rights or to ask you to
surrender the rights.
These restrictions translate to certain responsibilities for you if you distribute copies of the software,or if you
modify it.
For example,if you distribute copies of such a program, whether gratis or for a fee,you must give the recipients
all the rights that you have.You must make sure that they, too, receive or can get the source code.And you must
show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software,and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the software.
Also,for each author's protection and ours,we want to make certain that everyone understands that there is no
warranty for this free software. If the software is modified by someone else and passed on, we want its recipients
to know that what they have is not the original,so that any problems introduced by others will not reflect on the
original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors
of a free program will individually obtain patent licenses,in effect making the program proprietary. To prevent this, we
have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying,distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING,DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it
may be distributed under the terms of this General Public License.The "Program", below, refers to any such program
or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that
is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into
another language. (Hereinafter,translation is included without limitation in the term "modification".) Each licensee is
addressed as "you".
Activities other than copying,distribution and modification are not covered by this License; they are outside its scope.
The act of running the Program is not restricted,and the output from the Program is covered only if its contents
constitute a work based on the Program (independent of having been made by running the Program).Whether that is
true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it,in any medium, provided
that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of
warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other
recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection
in exchange for a fee.
5. You are not required to accept this License, since you have not signed it. However,nothing else grants you permission
to modify or distribute the Program or its derivative works.These actions are prohibited by law if you do not accept this
License. Therefore, by modifying or distributing the Program (or any work based on the Program),you indicate your
acceptance of this License to do so, and all its terms and conditions for copying,distributing or modifying the Program or
works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a
license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.You
may not impose any further restrictions on the recipients' exercise of the rights granted herein.You are not responsible
for enforcing compliance by third parties to this License.
7. If,as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to
patent issues),conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the conditions of this License.If you cannot distribute so as to
satisfy simultaneously your obligations under this License and any other pertinent obligations,then as a consequence
you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of
the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both
it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance,the balance of the
section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution
system,which is implemented by public license practices.Many people have made generous contributions to the wide
range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted
interfaces,the original copyright holder who places the Program under this License may add an explicit geographical
distribution limitation excluding those countries,so that distribution is permitted only in or among countries not thus
excluded.In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time
to time.Such new versions will be similar in spirit to the present version,but may differ in detail to address new
problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License
which applies to it and "any later version", you have the option of following the terms and conditions either of that
version or of any later version published by the Free Software Foundation.If the Program does not specify a version
number of this License, you may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are
different,write to the author to ask for permission. For software which is copyrighted by the Free Software
Foundation,write to the Free Software Foundation; we sometimes make exceptions for this.Our decision will be
guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the
sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM,
TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,BUT NOT LIMITED TO,THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH YOU.SHOULD THE PROGRAM PROVE DEFECTIVE,YOU
ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER,OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM
AS PERMITTED ABOVE,BE LIABLE TO YOU FOR DAMAGES,INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES
SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to
achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so,attach the following notices to the program. It is safest to attach them to the start of each source file to
most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a
pointer to where the full notice is found.
one line to give the program's name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation; either version 2
of the License,or (at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not,write to the Free Software
Foundation,Inc., 51 Franklin Street,Fifth Floor,Boston,MA 02110-1301,USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive,make it output a short notice like this when it starts in an interactive mode:
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
Of course, the commands you use may be called something other than `show w' and `show c'; they could even be
mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school,if any, to sign a "copyright disclaimer"
for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright
interest in the program `Gnomovision'
(which makes passes at compilers) written
by James Hacker.
signature of Ty Coon,1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs.If your program is
a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is
what you want to do, use the GNU Lesser General Public License instead of this License.
Gnomovision version 69,Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details
type `show w'. This is free software,and you are welcome
to redistribute it under certain conditions; type `show c'
for details.
Note on environmental protection:
After the implementation of the European
Directive 2012/19/EU and 2006/66/EU in
the national legal system, the following
applies: Electric and electronic devices as
well as batteries must not be disposed of
with household waste. Consumers are
obliged by lawto return electrical and
electronic devices as well as batteries at
the end of their service lives to the public
collecting points set up for this purpose
or point of sale. Details to this are defined
by the national law of the respective country.
This symbol on the product, the instruction
manual or the package indicates that a
product is subject to these regulations.
By recycling, reusing the materials or other
forms of utilising old devices/Batteries, you
are making an important contribution to
protecting our environment.
GB
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from
the Program,and can be reasonably considered independent and separate works in themselves,then this License,
and its terms,do not apply to those sections when you distribute them as separate works. But when you distribute
the same sections as part of a whole which is a work based on the Program,the distribution of the whole must be
on the terms of this License,whose permissions for other licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based
on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope
of this License.
2. You may modify your copy or copies of the Program or any portion of it,thus forming a work based on the Program,
and copy and distribute such modifications or work under the terms of Section 1 above,provided that you also meet
all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of
any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the
Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this
License.
c) If the modified program normally reads commands interactively when run,you must cause it,when started
running for such interactive use in the most ordinary way,to print or display an announcement including an
appropriate copyright notice and a notice that there is no warranty (or else,saying that you provide a warranty)
and that users may redistribute the program under these conditions, and telling the user how to view a copy of
this License. (Exception: if the Program itself is interactive but does not normally print such an announcement,
your work based on the Program is not required to print an announcement.)
3. You may copy and distribute the Program (or a work based on it,under Section 2) in object code or executable
form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed
under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more
than your cost of physically performing source distribution,a complete machine-readable copy of the
corresponding source code,to be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial distribution and only if you received the program in
object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it.For an executable
work, complete source code means all the source code for all modules it contains,plus any associated interface
definition files, plus the scripts used to control compilation and installation of the executable. However,as a
special exception,the source code distributed need not include anything that is normally distributed (in either
source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which
the executable runs,unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place,then
offering equivalent access to copy the source code from the same place counts as distribution of the source code,
even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify,sublicense, or distribute the Program except as expressly provided under this License.
Any attempt otherwise to copy, modify,sublicense or distribute the Program is void,and will automatically terminate
your rights under this License.However,parties who have received copies,or rights, from you under this License
will not have their licenses terminated so long as such parties remain in full compliance.
Manufacturer: BrosTrend Technology LLC
Address: 8 The Green, Suite A, Dover City, DE, U.S.A., Zip code 19901
Website: www.brostrend.com
Telephone: +86-17796126768
For EU/EFTA, this product can be used in the following countries:
Authorized U.K. Representative Information
Name: APEX CE SPECIALISTS LIMITED
Address: 89 Princess Street, Manchester, M1 4HT, UK
Contact: Wells
Telephone No.: 00441616371080
E-Mail: [email protected]
Email address:
support@brostrend.com
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Operations in the 5.15-5.25GHz band are restricted to indoor use only.
This equipment should be installed and operated with minimum distance 20cm between the device and
your body.
The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
For passthrough devices, plug the power strips into the integrated electrical sockets of the devices, but
devices of the same or another type not be stacked in normal use.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment.
(2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Declaration of Conformity
Hereby, BrosTrend Technology LLC declares that the radio equipment type A3 are in compliance
with Directive 2014/53/EU and 2014/30/EU. The full text of the EU declaration of conformity is available
at the following Internet address:https://brostrend.me/regulatory
EIRP Power (Max.):
2.4GHz: < 20dBm
5GHz: < 21dBm
Software Version: V16.03.19.06_multi
Operating Frequency:
2.4GHz: EU/2412-2472 MHz (CH1-CH13)
5GHz: 5180-5825 MHz (CH36-CH165)
Material No.: 0044
Q3: What should I do if I forgot my WiFi password?
If you still have your Web UI login password, connect a computer to the access point
via an Ethernet cable, log into the web UI and go to WiFi Settings to retrieve
your WiFi password.
If you forgot both your WiFi password and Web UI login password, refer to Q2 to reset
the access point first, then create a new WiFi password and login password by setting
up the access point again.
