Bryant COALMBBNRB02-A10 User manual

P/N 2547-7204-00 EN Rev. A
ATTENTI N: Please take a few minutes to thoroughly read this
user guide which should be saved for future reference and passed
on to any subsequent owner.
Car on Monoxide Alarm
User G ide
Model: COALMBBNRB02-A10 (900-0280-BRY)
AC Plug-in Operated with Sealed Lithium Battery Backup

Carbon Monoxide Alarm Procedure
WARNING: Activation of the CO
Alarm indicates the presence of Carbon
Monoxide (CO) which can kill you.
What to do When the Alarm Sounds!
If alarm sounds 4 quick beeps, 5 seconds off:
1) Operate Test /Reset button.
2) Call your emergency services (FIRE DEPT or 911).
3) Immediately MOVE TO FRESH AIR – outdoors or by an open
door / Window.
4) After following steps 1-3, if the alarm reactivates within a 24
hour period, repeat steps 1-3 and call a qualified appliance
technician to investigate sources of CO from fuel burning
equipment and appliances, and to inspect for proper operation
of equipment.
If problems are identified during this inspection, have the
equipment serviced immediately. Note any combustion equipment
not inspected by the technician and consult the manufacturer’s
instructions, or contact the manufacturer directly for more
information about CO safety and the equipment. Make sure that
motor vehicles are not, or have not been, operating in a garage
attached or adjacent to the residence.
Never restart the source of a C problem until it has been
corrected. Never ignore the sound of the alarm!
If the alarm is sounding, pressing the Test/Hush button will
terminate the alarm. If the C condition that caused the alert
in the first place continues, the alarm will reactivate. If the
unit alarms again within six minutes, it is sensing high levels
of C which can quickly become a dangerous situation.
PHONE NUMBER:
PHONE NUMBER:

Welcome
Note: Many times throughout this User Guide, we will refer to
Carbon Monoxide as “C ”.
This Bryant carbon monoxide (CO) alarm is an important part of your
family’s home safety plan. This alarm has been designed and tested to
detect CO buildup in a residential environment. Your alarm is for use
specifically in the home, but not for use in a boat or recreational vehicle.
As an owner of a CO alarm, there are some basic facts you should know
about for your protection.
Many people think that CO alarms operate like smoke alarms. Like
smoke alarms, CO alarms monitor the air in your home and sound a
loud alarm to warn you of trouble. The way you respond to a CO alarm
is quite different than a smoke alarm. That’s because a house fire and a
CO problem are two distinctly different situations. If your smoke alarm
were to alarm, you would quickly be able to judge the level of danger
you were in with your senses. You can see and smell the smoke, feel the
heat, see, and possibly hear the fire burning. You can also readily see if
your smoke alarm is alarming in a non-emergency situation. Because
your sense of sight, smell, hearing and touch give you information, you
can almost instantly judge what action to take if you hear your smoke
alarm.
CO is an invisible, odorless, tasteless and non-irritating gas – completely
undetectable to your senses. That’s why it is important to your safety
that you have a CO alarm.
Important Warning Statements
IMP RTANT: This carbon monoxide alarm is designed to detect
carbon monoxide from ANY source of combustion. It is N T
designed to detect smoke, fire, or any other gas.
WARNING: Carbon monoxide alarms are not smoke alarms.
This carbon monoxide alarm is not a substitute for installing and
maintaining an appropriate number of smoke alarms in your
home.
This carbon monoxide alarm will not sense smoke, fire, or any
poisonous gas other than carbon monoxide even though carbon
monoxide can be generated by fire. For this reason you must
install smoke alarms to provide early warning of fire and to
protect you and your family from fire and its related hazards.
CAUTI N: This alarm will only indicate the presence of carbon
monoxide at the sensor. Carbon monoxide may be present in
other areas.
!

Important Warning Statements
WARNING: This product is intended for use in ordinary indoor
locations of family living units, not for use in boats or
recreational vehicles. It is not designed to measure compliance
with commercial or industrial standards. It is not suitable for
installation in hazardous locations as defined in your local
building code.
The installation of this device should not be used as a substitute
for proper installation, use and maintenance of fuel burning
appliances, including appropriate ventilation and exhaust
systems. It does not prevent C from occurring, nor can it solve
an existing C problem.
WARNING: This device is designed to protect individuals from
acute effects of carbon monoxide exposure. It may not fully
safeguard individuals with specific medical conditions. If in doubt,
consult a medical practitioner.
Individuals with medical problems may consider using warning
devices which provide audible and visual signals for carbon
monoxide concentrations under 30 PPM.
This carbon monoxide alarm requires a continuous supply of
electrical power – it will not work without power. Models
without battery backup will not operate during power failure.
This alarm has not been investigated for carbon monoxide
detection below 70 PPM.
Contents of This User Guide
1. Information About Carbon Monoxide
2. Product Features and Specifications
3. Installation Locations
4. Installation Instructions
5. Alarm Characteristics
6. perating Characteristics
7. Maintenance
8. Limited Warranty

1. Information About Carbon Monoxide
General Car on Monoxide Information
Carbon monoxide is a colorless, odorless and tasteless poison gas that
can be fatal when inhaled. CO inhibits the blood’s capacity to carry
oxygen.
Periodically review this alarm user guide and discuss your CO alarm
emergency procedure with all the members of your family. Never ignore
a CO alarm. A true alarm is an indication of potentially dangerous levels
of CO. CO alarms are designed to alert you to the presence of CO
before an emergency – before most people would experience symptoms
of CO poisoning, giving you time to resolve the problem calmly.
Determine if anyone in the household is experiencing symptoms of CO
poisoning. Many cases of reported CO poisoning indicate that while
victims are aware they are not well, they become so disoriented they are
unable to save themselves by either exiting the building or calling for
assistance. Also, young children and household pets may be the first
affected. You should take extra precautions to protect high-risk persons
from CO exposure because they may experience ill effects from CO at
levels that would not ordinarily affect a healthy adult.
Symptoms of CO Poisoning
The following common symptoms are related to CO poisoning and
should be discussed with ALL members of the household.
Mild Exposure:
Slight headache, nausea, vomiting, fatigue (often described as “flu-like”
symptoms).
Medium Exposure:
Severe throbbing headache, drowsiness, confusion, fast heart rate.
Extreme Exposure:
Unconsciousness, convulsions, cardio-respiratory failure, death.
If you experience even mild symptoms of CO poisoning, consult your
doctor immediately!

1. Information About Carbon Monoxide
Car on Monoxide PPM Levels
Model COALMBBNRB02-A10 is equipped with a digital display that
shows levels of CO (displayed in PPM – parts per million). Learn the
difference between dangerous, high, mid and low levels.
Dangerous Levels:
When someone is experiencing symptoms of CO poisoning and CO
readings are generally above 100 PPM. Anytime someone is experiencing
the symptoms of CO poisoning this should be treated as an emergency.
See “What to do When the Alarm Sounds” (inside front cover).
High Levels:
Generally above 100 PPM, with no one experiencing symptoms. This
should be treated as an urgent situation. See “What to do When the
Alarm Sounds” (inside front cover).
Mid Levels:
Generally between 50 PPM to 100 PPM. This should be cause for
concern and should not be ignored or dismissed. See “What to do
When the Alarm Sounds” (inside front cover).
Low Levels:
Generally below 50 PPM. Bryant recommends you take action to
eliminate the source of CO. See “What to do When the Alarm Sounds”
(inside front cover).
Possi le Sources of Car on Monoxide
Inside your home, appliances used for heating and cooking are the most
likely sources of CO. Vehicles running in attached garages can also
produce dangerous levels of CO.
CO can be produced when burning any fossil fuel, such as gasoline,
propane, natural gas, oil and wood. It can be produced by any fuel-
burning appliance that is malfunctioning, improperly installed, or not
ventilated correctly, such as:
• Automobiles, furnaces, gas ranges/stoves, gas clothes dryers, water
heaters, portable fuel burning space heaters and generators,
fireplaces, wood-burning stoves and certain swimming pool heaters.
• Blocked chimneys or flues, back drafts and changes in air pressure,
corroded or disconnected vent pipes, loose or cracked furnace
exchangers.
• Vehicles and other combustion engines running in an open or closed
garage, attached or near a home.
• Burning charcoal or fuel in grills and hibachis in an enclosed area.

1. Information About Carbon Monoxide
Conditions That Can Produce Car on Monoxide
The following conditions can result in transient CO situations:
• Excessive spillage or reverse venting of fuel-burning appliances caused
by outdoor ambient conditions, such as, wind direction and/or
velocity, including high gusts of wind, heavy air in the vent pipes
(cold/humid air with extended periods between cycles).
• Negative pressure resulting from the use of exhaust fans.
• Simultaneous operation of several fuel-burning appliances competing
for limited internal air.
• Vent pipe connections vibrating loose from clothes dryers, furnaces, or
water heaters.
• Obstructions in, or unconventional, vent pipe designs which can
amplify the above situations.
• Extended operation of unvented fuel-burning devices (range, oven,
fireplace, etc.).
• Temperature inversions which can trap exhaust gases near the ground.
• Vehicle idling in an open or closed garage, or near a home.
To be safe, know the possible sources of CO in your home. Keep fuel-
burning appliances and their chimneys and vents in good working
condition. Learn the early symptoms of exposure, and if you suspect CO
poisoning, move outside to fresh air and get emergency help. Your first
line of defense is an annual inspection and regular maintenance of your
appliances. Contact a licensed contractor or call your local utility
company for assistance.
Information A out Car on Monoxide Alarms –
What They Can and Cannot Do:
CO alarms provide early warning of the presence of CO, usually before a
healthy adult would experience symptoms. This early warning is possible,
however, only if your CO alarm is located, installed and maintained as
described in this guide.
Because carbon monoxide is a cumulative poison, long-term exposures to low
levels may cause symptoms, as well as short-term exposures to high levels.
This Bryant unit has a time-weighted alarm – the higher the level of CO
present, the sooner the alarm will be triggered.

1. Information About Carbon Monoxide
This CO alarm can only warn you of the presence of CO. It does not prevent
CO from occurring, nor can it solve an existing CO problem. If your unit has
alarmed and you’ve provided ventilation by leaving your windows and doors
open, the CO buildup may have dissipated by the time help responds.
Although your problem may appear to be temporarily solved, it’s crucial that
the source of the CO is determined and that the appropriate repairs are made.
This CO alarm is designed to act as a monitor; it is not designed for use as a
short-term testing device to perform a quick check for the presence of CO.
CO alarms have limitations. Like any other electronic device, CO alarms are
not fool-proof. CO alarms have a limited operational life. You must test your
CO alarm weekly, because it could fail to operate at any time.
If your CO alarm fails to test properly, or if its self-diagnostic test reveals a
malfunction, immediately have the unit replaced. This alarm will not monitor
CO levels while in an error condition.
CO alarms can only sense CO that reaches the unit’s sensor. It’s possible that
CO may be present in other areas without reaching the alarm. The rate and
ability that which CO reaches the alarm may be affected by:
• Doors or other obstructions.
• Fresh air from a vent, an open window or other source.
• CO being present on one level of the home and not reach a CO alarm
installed on a different level. (For example, CO in the basement may not
reach an alarm on the second level, near the bedrooms).
For these reasons, we recommend you provide complete coverage by placing
a CO alarm on every level of the home. Please carefully read all information
on properly installing this CO alarm.
CO alarms should not be used to detect the presence of natural gas
(methane), propane, butane, or other combustible fuels.

2. Product Features and Specifications
Model C ALMBBNRB02-A10
Alarm
So nder
Test/H sh
B tton
Red Alarm
Light
Digital
Display
Low Battery Warning
If the battery power is low, the unit will chirp every 60 seconds,
and the display will show "Lb" to indicate the alarm must be
replaced. THE ALARM MUST BE REPLACED IMMEDIATELY!
Low Battery HUSH®CONTROL
When the unit produces a low battery warning, the Low Battery
HUSH®feature allows you to press the Test/Hush button on the alarm
and disable the “chirp” for a period of approximately 10 hours. This
gives you a chance to replace the alarm at a more convenient time
without sacrificing your safety by disconnecting the alarm from
power. During this Low Battery HUSH®period, your alarm is
monitoring for CO.
If the alarm does not go into Low Battery Hush, the battery power is
below the Low Battery Hush threshold. REPLACE THE ALARM
IMMEDIATELY!
Am ient Light Sensor
This alarm includes a feature to determine dark or light conditions.
This feature will:
1. Help prevent low battery chirping at night, (when ambient
conditions are dark).
2. Dim the display in low light conditions, (night time and darker
rooms), and brighten the display in bright light conditions.
Green Operate
Light / Ambient
Light Sensor
Peak
Level
Deactivation /
Discharge Switch
Deactivation /
Discharge Switch Cover
Rotating AC Pl g

2. Product Features and Specifications
End of unit life Warning
IMP RTANT: Ten (10) years after the initial power up, this alarm
will “beep” two times every 30 seconds to indicate that it is time
to replace the alarm. Display will show "End".
To help identify the date to replace the alarm, a label has been affixed to
the side of the alarm. Write the “replace by” date (ten years from power
up) in a permanent marker on this label.
End of unit life Hush Control
The End of unit Life Hush feature allows you to silence End of Unit life
chirping, for a period of 3 days, by pressing the Test/Hush button. This
feature can be used 10 times within 30 days, allowing you to replace
the alarm at a more convenient time. After 30 days, the alarm will no
longer detect CO. REPLACE ALARM IMMEDIATELY!"
Temperature:
Operating Range: 4.4 C (40 F) to 37.8 C (100 F)
Humidity:
Operating range: 10-95% relative humidity (RH), non-condensing
Audible Alarm:
85+ dB at 10’ @ 3.4±0.5 KHz pulsing alarm
Sensor:
Electrochemical
Power:
120 volts AC, 60 Hz, 90 mA max, 3 volt sealed lithium battery backup
Alarm Response Times:
70 PPM = 60-240 min., 150 PPM = 10-50 min., 400 PPM = 4-15 min.

Recommended Installation
Locations
CO alarms should be mounted in or
near bedrooms and living areas. It is
recommended that you install a Bryant
CO alarm on each level of your home.
When choosing your installation
locations, make sure you can hear the
alarm from all sleeping areas. If you
install only one CO alarm in your home, install it near bedrooms, not in the
basement or furnace room.
• The CO alarm plugs into a wall socket. Children must be taught not to
handle the CO alarm.
Locations To Avoid
IMP RTANT: Improper location can affect the sensitive electronic
components in this alarm. To avoid causing damage to the unit, to provide
optimum performance, and to prevent unnecessary nuisance alarms:
• Do not install in kitchens, garages or furnace rooms that may expose the
sensor to substances that could damage or contaminate it.
• Do not install in areas where the temperature is colder than 4.4 C (40 F)
or hotter than 37.8 C (100 F) such as crawl spaces, attics, porches and
garages.
• Do not install within 5 ft. of heating or cooking appliances. (Bryant
recommends 15 ft. to prevent nuisance alarms).
• Do not install near vents, flues, chimneys or any forced/unforced air
ventilation openings.
• Do not install near ceiling fans, doors, windows or areas directly exposed
to the weather.
• Do not install in dead air spaces, such as peaks of vaulted ceilings or
gabled roofs, where CO may not reach the sensor in time to provide early
warning.
• Do not install this unit near deep-cell large batteries. Large batteries have
emissions that can cause the alarm to perform at less than optimum
performance.
• Do not obstruct the vents located on the alarm. Do not place the alarm
where drapes, furniture or other objects block the flow of air to the vents.
3. Installation Locations
DINING KITCHEN BEDROOM BEDROOM
BEDROOM
LIVING ROOM
Recommended Locations

When you first power up the alarm: The red Alarm LED will light and
the alarm will chirp once.
CO alarm power indicators:
AC - Digital display constantly on.
DC Only - Green LED flashes briefly once every 60 seconds.
Within a few minutes, your carbon monoxide alarm will start monitoring for
CO and will continue to do so as long as it receives power.
Whenever the COALMBBNRB02-A10 is operating, the digital display will
display “0”(with AC applied) to indicate the unit is monitoring for CO.
How to Install Your Alarm
Direct Plug Alarm
To install:
1. Remove the switch cover.
2. Choose a standard 120V unswitched outlet to
plug the alarm into.
3. If outlet is mounted sideways (horizontally), rotate
the plug and plug the alarm in.
Note: This model is equipped with a feature that automatically activates
the battery backup when the alarm is plugged into an AC outlet for the
first time.
CAUTI N: Do not rotate the alarm while it is plugged into an
outlet, as damage to plug may result.
Important Labels Provided
Two labels have been provided that have important information on what to
do in case of an alarm. Add the phone number of your emergency service
provider in the space provided. Place one label next to the alarm after it is
mounted, and one label near a fresh air source such as a door or window.
!
4. Installation Instructions
90º ROTATING DIRECT
PLUG
5. Alarm Characteristics
Car on Monoxide Alarm Indicator
When the alarm senses a dangerous level of CO, the unit will emit a
loud alarm pattern. The alarm pattern is 4 quick beeps followed by 5
seconds of silence. This cycle repeats as long as a dangerous CO
conditions exist. The red Alarm LED will flash the same pattern and the
PPM will be displayed on the digital display.
The digital display will be brightly lit if the unit is in alarm.
WARNING: If at any time you test the alarm and it does not
perform as described, have it replaced immediately.
6. perating Characteristics

Operating and Alarm Characteristics
LED Display Shows Alarm Sound Unit Status Recommendation
"---" then "888" 4 quick beeps,
5 seconds
silence,
repeated once
Self checking (Test
button was pressed)
None – CO has not
been detected.
Steady “0” displayed. None Normal AC operation
(sensing no CO) and
with a good battery.
None
An alternating display
of "CO" and the CO
concentration from
30-999.
4 quick beeps,
5 seconds
silence,
repeating
Alarm condition.
Dangerous
concentrations of CO
detected
Refer to “What to do
When the Alarm
Sounds” (inside front
cover)
Display alternates
between 'Lb" and
current CO level, (0-
999).
One quick
beep every
60 seconds
AC powered and
in Low Battery
condition
Replace alarm.
Steady “Err “displayed One quick
beep every 30
seconds
Unit malfunction
If "Err" continues, unit
has malfunctioned and
must be replaced
immediately.
Unit will not respond to
CO. Press the Peak Level
button while unit is in
"Err"mode to obtain error
code and call Product
Support line.
No display. Green LED
flashes briefly once
every 60 seconds.
None Battery backup
operation. Unit
monitoring for CO.
Verify AC power is
restored as soon as
possible to conserve
battery.
6. perating Characteristics
If the alarm senses dangerous levels of CO, the digital display will alternate between
"CO" and the measured CO concentration in parts per million (PPM), and the alarm
will emit an audible alarm pattern. This alarm will display a “0” if CO concentrations
between 0 and 30 PPM have been detected within the last 15 seconds.
When the unit is first powered up, the digital display will show three “eights” –
indicating the alarm is in the start-up mode. The three “eights” will remain for
approximately 5 seconds. After 5 seconds, the alarm should display “0” and begin
monitoring the air for CO and will continue to do so as long as it receives power.
The digital display will be brightly lit if the unit is in alarm, or in high light, and
then will become dim in the standby condition during low light conditions.
The following table illustrates the possible digital displays, describes the
audible alarm patterns, and the recommended actions to take.
"End" displayed.
Red LED flashes
two times every 30
seconds
2 quick beeps
every 30
seconds.
End of unit life Replace unit immediately.
Refer to Section 2 for End
of Life Warning. See
Discharge section on next
page.
An alternating
display of
"PCO" and the CO
concentration (PPM)
None Unit has detected
100ppm or more CO
Push test/reset button,
check appliances

Peak Level Event Alert
A Peak Level Event occurs whenever CO concentrations are greater than
100 PPM. The display will alternate between "PCO" and the currently
measured CO concentration, (0-999), even if that concentration has returned
to 0 PPM, (see Peak Level Memory section below to display peak level CO
from the event). The display will alternate continuously on AC power, and will
briefly display once every minute on DC only. This will continue until:
1. The unit goes into alarm or,
2. CO concentration level drops below 100 PPM and the user clears the
Peak CO Memory, (see Peak Level Memory Reset section below)
If the CO concentration is greater than 30 PPM and less than 100 PPM,
the display will indicate the measured CO concentration only.
Peak Level Memory
When the Peak Level button is pressed and held, the display shows the
highest CO reading taken by the CO alarm since its last reset or power
up. The Peak Level display feature will display levels between 11-999
PPM. Although the Peak Level feature will display levels below 30 PPM,
these levels will not result in an alarm no matter how long the device is
exposed to these levels. The Peak Level feature is helpful in identifying if
you have had a CO reading since resetting the alarm.
Concentrations of CO between 1 and 30 PPM can often occur in
normal, everyday conditions. Concentrations of CO below 30 PPM may
be an indication of a transient condition that may appear today and
never reappear. Some CO conditions may start out as low level leaks but
could develop into CO concentrations that may become harmful.
Peak Level Memory Reset
Press and hold the Peak Level button, then press and hold the Test/Hush
button. When the number on the display reads "0", release both
buttons. The memory will be cleared and the alarm will begin
monitoring for CO.
Discharge
At end of unit life, locate the deactivation/discharge switch and push the
switch in the direction shown until switch clicks
into place. This will silence the end of unit life
life or low battery chirping, drain the battery,
and render the unit safe for disposal.
6. perating Characteristics

7. Maintenance
N TE: This unit is sealed. The cover is not removable.
Due to the loudness of the alarm, we suggest that you place your
fingers over the sounder opening while testing your alarm.
Caution: Continuous exposure to the high sound level of this alarm
over an extended period of time may cause hearing loss.
Testing
To test the alarm, press the Test/Hush button. If the unit is operating properly,
you will hear 4 quick beeps – followed by 5 seconds of silence – followed by 4
quick beeps. The display will show in sequence "---" then "888". Within
several seconds the unit will return to monitor for CO.
Note: You do not need to press the Test button to take a C reading.
Maintenance Tips
To keep your alarm in good working order, you must follow these steps:
• Test the alarm once a week by pressing the Test/Hush button.
• Vacuum the alarm cover once a month to remove accumulated dust.
• Never use detergents or solvents to clean the alarm. Chemicals can
permanently damage or temporarily contaminate the sensor.
• Avoid spraying air fresheners, hair spray, paint or other aerosols near the
alarm.
• Do not paint the unit. Paint will seal the vents and interfere with proper
sensor operation.
Move the CO Alarm to a remote location, to prevent possible damage or
contamination of the sensor, prior to performing any of the following:
• Staining or stripping floors or furniture, painting or wall-papering
• Using aerosols or adhesives
WARNING: Reinstall the CO Alarm as soon as possible to assure
continuous protection.
The following is a list of substances that at high levels can damage the sensor
or cause temporary readings that are not CO readings:
• Ethylene, ethanol, alcohol, iso-propanol, benzene, toluene, ethyl acetate,
hydrogen, hydrogen sulfide and sulfur dioxide.
• Also most aerosol sprays, alcohol based products, paint, thinner, solvent,
adhesive, hair spray, after shave, perfume, auto exhaust (cold start) and
some cleaning agents.
!

7. Maintenance
FCC C MPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help

Ten Year Limited Warranty
Warranty Coverage: The manufacturer warrants to the original consumer purchaser, that this
product will be free of defects in material and workmanship for a period of ten(10) years from
date of purchase. The manufacturer’s liability hereunder is limited to replacement of the
product, repair of the product or replacement of the product with repaired product at the
discretion of the manufacturer. This warranty is void if the product has been damaged by
accident, unreasonable use, neglect, tampering or other causes not arising from defects in
material or workmanship. This warranty extends to the original consumer purchaser of the
product only.
Warranty Disclaimers: Any implied warranties arising out of this sale, including but not
limited to the implied warranties of description, merchantability and fitness for a particular
purpose, are limited in duration to the above warranty period. In no event shall the
Manufacturer be liable for loss of use of this product or for any indirect, special, incidental or
consequential damages, or costs, or expenses incurred by the consumer or any other user of
this product, whether due to a breach of contract, negligence, strict liability in tort or
otherwise. The Manufacturer shall have no liability for any personal injury, property damage or
any special, incidental, contingent or consequential damage of any kind resulting from gas
leakage, fire or explosion. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. Some states do not allow the
exclusion or limitation of consequential or incidental damages, so the above limitations or
exclusions may not apply to you.
Legal Remedies: This warranty gives you specific legal rights and you may also have other
rights that vary from state to state.
Warranty Performance: During the above warranty period, your product will be replaced with
a comparable product if the defective product is returned in a postage paid package to the
following address: Kidde, Customer Service Department, 1016 Corporate Park Drive, Mebane,
NC 27302 USA, together with proof of purchase date. Please include a note describing the
problem when you return the unit. The replacement product will be in warranty for the
remainder of the original warranty period or for six months, whichever is longer. Other than the
cost of postage, no charge will be made for replacement of the defective product. In many
cases the quickest way to exchange your alarm is to return it to the original place of purchase.
If you have questions, call Kidde customer service department.
IMP RTANT: Do not remove unit back cover. Back cover removal will void warranty.
Your Bryant Carbon Monoxide Alarm is not a substitute for property, disability, life or other
insurance of any kind. Appropriate insurance coverage is your responsibility. Consult your
insurance agent.
The above warranty may not be altered except in writing signed by both parties hereto.
QUESTIONS OR FOR MORE INFORMATION
Call our Product Support Line at 1-800-880-6788 or contact
us at our website at www.kidde.com
Kidde, 1016 Corporate Park Drive, Mebane, NC 27302
8. Limited Warranty