Bryant LEGACY 213R Operation manual

Product Data
MODEL 213R
LEGACYt--RNC SERIES HEAT PUMP
SIZES 018 TO 060
1--1/2 TO 5 NOMINAL TONS
Shown with optional dense coil guard
FEATURES / BENEFITS
Efficiency
S13 SEER/ 11 EER / Up to 8.6 HSPF (Nominal)
SMicrotube Technologytrefrigeration system
SIndoor air quality accessories available
Sound
SSound level as low as 75 dBA
Comfort
SSystem supports Thermidistattor standard thermostat
controls
Reliability
SFront--seating service valves
SScroll compressor
SFilter drier
SLoss of charge pressure switch
SBalanced refrigeration system for maximum reliability
Durability
DuraGuardtprotection package:
SSolid, Durable sheet metal construction
SWire coil guard
SBaked--on, complete coverage, powder paint
Applications
SLong--line -- up to 250 feet total equivalent length, up
to 200 feet condenser above evaporator, or up to 80 ft.
evaporator above condenser (See Longline Guide for
more information.)
SLow ambient (down to --20_F) with accessory kit
Warranty
Single Phase
S5 year limited compressor warranty
S5 year limited parts warranty
Three Phase
S5 year limited compressor warranty
S1 year limited parts warranty

2
MODEL NUMBER NOMENCLATURE
12345678910111214
N N N A A/N N N N N A/N A/N N A
21 3 R N A 036 0 0 0 0
Prod-
uct
Family
Tier SEER Major Series Voltage Variations Cooling Capacity Open Open Open Series
2=HP
1=
Legacy
RNC
3=13 SEER R=R---22
N=
208/230---1
P=208/230
--- 3
E=460/3
A=Standard
G=Dense Coil
Guard
0=Not
Defined
0=Not
Defined
0=Not
Defined
A=
Original
Series
REGISTERED
ISO 9001:2000
As an Energy Star®Partner, Bryant
Heating & Cooling Systems has
determined that this product meets the
ENERGY STAR®guidelines for energy
efficiency.
Refer to the combination ratings in
Product Data for system combinations that
meet Energy Star guidelines.
STANDARD FEATURES
Feature 18 24 30 36 42 48 60
13 SEER XXXXXXX
Scroll Compressor XXXXXXX
Wire Coil Guard XXXXXXX
FieldInstalledFilterDrier XXXXXXX
Front Seating Service Valves XXXXXXX
Internal Pressure Relief Valve XXXXXXX
Internal Thermal Overload XXXXXXX
Long Line capability XXXXXXX
Low Ambient capability with Kit XXXXXXX
Loss of Charge Pressure Switch XXXXXXX
213R

3
PHYSICAL DATA
UNIT SIZE --- SERIES 018---A 024---A 030---A 036---A 042---A 048---A 060---A
Operating Weight (lb) 159 160 208 211 233 269 295
Shipping Weight (lb) 184 185 240 242 262 300 327
Compressor Type Scroll
REFRIGERANT Freon®( R --- 2 2 )
Control T X V ( R --- 2 2 H a r d S h u t o f f )
Charge (lb) 5.5 67.5 810 14 15.5
COND FAN Propeller Type, Direct Drive
Air Discharge Vertical
Air Qty. (CFM) 2233 2614 2614 3334 3334 4046 4046
Motor HP 1/12 1/10 1/10 1/8 1/8 1/5 1/5
Motor RPM 800 1100 1100 800 800 800 800
COND COIL
Face Area (Sq. ft.) 15.09 15.09 25.87 22.63 17.6 22.63 25.15
Fins per In. 20 20 20 20 20 20 20
Rows 1 1 1 1 2 2 2
Circuits 5 6 6 6 7 8 9
VALVECONNECT.(In.ID)
Vapor 5/8” 5/8” 3/4” 3/4” 7/8” 7/8” 7/8”
Liquid 3/8”
REFRIGERANT TUBES* (In. OD)
Vapor (0---80 Ft. Tube Length) 5/8” 5/8” 3/4” 3/4” 7/8” 7/8” 1---1/8”
Liquid (0---80 Ft. Tube Length) 3/8”
* For tubing sets between 80 and 200 ft. horizontal or 20 ft. vertical differential, consult the Longline Guideline.
Note: See unit Installation Instruction for proper installation.
VAPOR LINE SIZING AND COOLING CAPACITY LOSS
1--STAGE HEAT PUMP APPLICATIONS
LONG LINE APPLICATION: An application is considered
”Long line” when the total equivalent tubing length exceeds 80
ft. or when there is more than 20 Ft. vertical separation between
indoor and outdoor units. These applications require additional
accessories and system modifications for reliable system
operation. The maximum allowable total equivalent length is 250
ft. The maximum vertical separation is 200 ft. when outdoor unit
is above indoor unit, and 60 ft. when the outdoor unit is below
the indoor unit. Refer to Accessory Usage Guideline below for
required accessories. See Long--Line Application Guideline for
required piping and system modifications. Also, refer to the table
below for the acceptable vapor tube diameters based on the total
length to minimize the cooling capacity loss.
Unit Nominal Size (Btuh)
Acceptable Vapor
Line Diameter OD
(in.)
Cooling Capacity Loss (%)
Total Equivalent Line Length (ft.)
Standard Application Long Line Application
Requires Accessories
25 50 80 80+ 100 125 150 175 200 225 250
18000
R --- 2 2 H P
5/8 0 1 1 1 2 3 3 4 5 5 6
3/4 0 0 0 0 0 1 1 1 1 2 2
24000
R --- 2 2 H P
5/8 0 1 3 3 3 5 6 7 8 9 10
3/4 0 0 0 0 1 1 1 2 2 3 3
30000
R --- 2 2 H P
3/4 0 1 1 1 2 3 3 4 5 5 6
7/8 0 0 0 0 1 1 1 2 2 2 3
36000
R --- 2 2 H P
3/4 0 1 2 2 3 4 5 6 7 8 9
7/8 0 0 1 1 1 2 2 3 3 4 4
42000
R --- 2 2 H P 7/8 0 1 1 1 2 2 3 4 4 5 5
48000
R --- 2 2 H P 7/8 0 1 2 2 2 3 4 5 5 6 7
60000
R --- 2 2 H P
7/8 1 2 3 3 4 5 7 8 9 10 11
11/8 0 0 1 1 1 1 2 2 2 3 3
Standard Length = 80 ft. or less total equivalent length
Applications in this area are long line. Accessories are required as shown recommended on Long Line Application Guidelines
Applications in this area may have height restrictions that limit allowable total equivalent length, when outdoor unit is below indoor unit See
Long Line Application Guidelines
213R

4
ACCESSORY THERMOSTATS
THERMOSTAT / SUBBASE PKG. DESCRIPTION
TSTATBBPRH01---B*
ThermidistattControl — Non---Programmable/Programmable Thermostat with
Humidity Control (For use in Dual Fuel, AC, HP, and 2S applications. Includes Out-
door Air Temperature Sensor.)
TSTATBBPHH01---B* HybridHeatt(Dual Fuel) Thermostat — Auto Changeover, 7---Day Programmable,
°F/°C, Includes Outdoor Sensor (TSTATXXSEN01---B)
TSTATBBPHP01---B Thermostat — Auto Changeover, 7---Day Programmable, °F/°C , 2 --- S t a g e H e a t ,
1 --- S t a g e C o o l
TSTATBBNHP01---C Thermostat — Auto Changeover, Non--- Programmable, °F/°C , 2 --- S t a g e H e a t ,
1 --- S t a g e C o o l
TSTATBBSHP01 Standard Programmable Thermostat—Manual Changeover, 5--- 2 Day Program-
mable, °F/°C , 1 --- S t a g e H e a t / 1 --- S t a g e C o o l
TSTATBBBHP01*---B Builder’s Thermostat — Heat Pump, Non--- Programmable, °F/°C , 2 --- S t a g e H e a t ,
1---Stage Cool, Manual Changeover
TSTATXXSEN01--- B** Outdoor Air Temperature Sensor
TSTATXXNBP01 Backplate for Non---Programmable Thermostat
TSTATXXPBP01 Backplate for Programmable Thermostat and ThermidistattControl
TSTATXXSBP01 Backplate for Standard Programmable Thermostat
TSTATXXBBP01 Backplate for Builder’s Thermostat
TSTATXXCNV10{Thermostat Conversion Kit (4 to 5 Wire) — 10 Pack
* Do not use in zoning heat pump applications.
** Outdoor temperature sensor is an accessory for all Bryant electronic thermostats, except the non ---programmable air conditioner version and builder;s
thermostats. It allows the temperature at a remote location (outdoors) to be displayed on the thermostat. The outdoor air temperature sensor must be used
with the HybridHeatt(dual fuel) thermostat.
{Thermostat conversion kit is a 24---vac accessory that can turn a 4 ---wire thermostat application into a 5---wire application. This kit can also be used to
replace a broken thermostat wire, or add an extra wire when needed.
The outdoor air temperature sensor is included with the Thermidistat Control and HybridHeatt(dual fuel) thermostat.
ACCESSORIES
ORDER NUMBER DESCRIPTION (N)
018 -- A
(N)
024 -- A
(N)
030 -- A
(P)
030 -- A
(N)
036 -- A
(P)
036 -- A
(E)
036 -- A
(N)
042 -- A
(P)
042 -- A
(E)
042 -- A
(N)
048 -- A
(P)
048 -- A
(E)
048 -- A
(N)
060 -- A
(P)
060 -- A
(E)
060 -- A
HC32GE229 BALL BEARING MOTOR X
HC34GE240 BALL BEARING MOTOR XXX
HC36GE232 BALL BEARING MOTOR X X X X
HC40GE228 BALL BEARING MOTOR X X X X
KAACH1201AAA CRANKCASE HTR X X X X X X S S S S
KAACH1301AAA CRANKCASE HTR X X S S
KAACH1401AAA CRANKCASE HTR X X
KSACY0101AAA CYCLE PROTECTOR XXXXXXXXXXXXXXXX
KAAFT0101AAA FREEZE THERMOSTAT XXXXXXXXXXXXXXXX
KSAHS1501AAA HARD START X X X X X X
KSAHS1601AAA HARD START X
KSAHI0301R22 HIGH PRESS SW XXXXXXXXXXXXXXXX
KHAIR0101AAA ISOLATION RELAY XXXXXXXXXXXXXXXX
KSALA0201R22 LOW AMBIENT XXXXXXXXXXXXXXXX
KSALA0601AAA MOTORMASTER 230V X X X X X X X X X X X X
KSALA0701AAA MOTORMASTER 460V X X X X
KHAOT0201SEC OUTDOOR THERMO-
STAT
XXXXXXXXXXXXXXXX
KHAOT0301FST OUTDOOR THERMO-
STAT
XXXXXXXXXXXXXXXX
KHALS0401LLS SOLENOID VALVE XXXXXXXXXXXXXXXX
KSASH0601COP SOUND BLKT XXXXXXXXXXX
KSASH1801COP SOUND BLKT X X
KSASH2101COP SOUND BLKT XXX
KAACS0201PTC START ASSIST PTC X X X X X X X
KSASF0101AAA SUPPORT FEET XXXXXXXXXXXXXXXX
KAATD0101TDR TIME DELAY XXXXXXXXXXXXXXXX
KSATX0601HSO TXV XXXXXXXXXX
KSATX0701HSO TXV X X X
KSATX1001HSO TXV XXX
213R

5
ACCESSORY USAGE GUIDELINE
Accessory
REQUIRED FOR LOW---AMBI-
ENT APPLICATIONS
(Below 55°F)
REQUIRED FOR LONG
LINE APPLICATIONS*
(Over 80 Ft.)
REQUIRED FOR SEA
COAST APPLICATIONS
(Within 2 miles)
Crankcase Heater Yes Yes No
Evaporator Freeze Thermostat Yes No No
Accumulator No No No
Compressor Start Assist Capacitor and
Relay Yes Yes No
Motor Master®Control
o r L o w --- a m b i e n t P r e s s u r e S w i t c h Yes No No
Support Feet Recommended No Recommended
Liquid Line Solenoid Valve No See Long --- Line Application
Guideline No
Ball Bearing Fan Motor Yes{No No
* For tubing line sets between 80 and 200 ft. and/or 20 ft. vertical differntial, refer to Residential Split---System Longline Application Guideline.
{Required for Low---Ambient Controller (full modulation feature) and MotorMasterrControl only.
Accessory Description and Usage (Listed Alphabetically)
1. Ball--Bearing Fan Motor
A fan motor with ball bearings which permits speed reduction
while maintaining bearing lubrication.
Usage Guideline:
Required on all units when MotorMasterris used.
2. Compressor Start Assist -- Capacitor and Relay
Start capacitor and relay gives a ”hard” boost to compressor
motor at each start up.
Usage Guideline:
Required for reciprocating compressors in the
following applications:
Long line
Low ambient cooling
Hard shut off expansion valve on indoor coil
Liquid line solenoid on indoor coil
Required for single--phase scroll compressors in the
following applications:
Long line
Low ambient cooling
Suggested for all compressors in areas with a history of
low voltage problems.
3. Compressor Start Assist — PTC Type
Solid state electrical device which gives a ”soft” boost to the
compressor at each start--up.
Usage Guideline:
Suggested in installations with marginal power supply.
4. Crankcase Heater
An electric resistance heater which mounts to the base of the
compressor to keep the lubricant warm during off cycles.
Improves compressor lubrication on restart and minimizes the
chance of liquid slugging.
Usage Guideline:
Required in low ambient cooling applications.
Required in long line applications.
Suggested in all commercial applications.
5. Cycle Protector
The cycle protector is designed to prevent compressor short
cycling. This control provides an approximate 5--minute delay
after power to the compressor has been interrupted for any
reason, including power outage, protector control trip, thermostat
jiggling, or normal cycling.
6. Evaporator Freeze Thermostat
An SPST temperature--actuated switch that stops unit operation
when evaporator reaches freeze--up conditions.
Usage Guideline:
Required when low ambient kit has been added.
7. Isolation Relay
An SPDT relay which switches the low--ambient controller out of
the outdoor fan motor circuit when the heat pump switches to
heating mode.
Usage Guideline:
Required in all heat pumps where low ambient kit has
been added.
8. Liquid--Line Solenoid Valve (LLS)
An electrically operated shutoff valve which stops and starts
refrigerant liquid flow in response to compressor operation. It is
to be installed at the outdoor unit to control refrigerant off cycle
migration in the heating mode.
Usage Guideline:
An LLS is required in all long line heat pump
applications to control refrigerant off cycle migration in
the heating mode. See Long Line Guideline.
9. Low--Ambient Pressure Switch Kit
A long life pressure switch which is mounted to outdoor unit
service valve. It is designed to cycle the outdoor fan motor in
order to maintain head pressure within normal operating limits
(approximately 100 psig to 225 psig). The control will maintain
working head pressure at low--ambient temperatures down to 0_F
when properly installed.
Usage Guideline:
A Low--Ambient Pressure Switch or MotorMasterr
Low--Ambient Controller must be used when cooling operation is
used at outdoor temperatures below 55_F (12.8_C).
10. MotorMasterrLow--Ambient Controller
A fan--speed control device activated by a temperature sensor,
designed to control condenser fan motor speed in response to the
saturated, condensing temperature during operation in cooling
mode only. For outdoor temperatures down to --20_F (--28.9_C),
it maintains condensing temperature at 100_F±10_F (37.8_C±
-- 1 2 _C).
Usage Guideline:
A MotorMasterrLow Ambient Controller or
Low--Ambient Pressure Switch must be used when
cooling operation is used at outdoor temperatures
below 55_F (12.8_C).
Suggested for all commercial applications.
213R

6
Accessory Description and Usage (Listed Alphabetically) -- CONTINUED
11. Outdoor Air Temperature Sensor
Designed for use with Bryant Thermostats listed in this
publication. This device enables the thermostat to display the
outdoor temperature. This device also is required to enable
special thermostat features such as auxiliary heat lock out.
Usage Guideline:
Suggested for all Bryant thermostats listed in this
publication.
12. Outdoor Thermostat
An SPDT temperature--actuated switch which turns on
supplemental electric heaters when outdoor air temperature drops
below a user--selected set point.
Usage Guideline:
Electric supplemental heat applications in non--variable
speed indoor units when electric heat staging is desired.
Usage Guideline:
Some local codes may require limiting the heating head
pressure in the vapor line in some applications.
13. Secondary Outdoor Thermostat
An SPDT temperature--actuated switch which turns on
third--stage of supplemental electric heaters when outdoor air
temperature drops below the second--stage set point.
Usage Guideline:
Outdoor thermostat applications where electric heater is
capable of 3--stage operation.
14. Sound Hood
Wraparound sound reducing cover for the compressor. Reduces
the sound level up to 2 dBA.
Usage Guideline:
Suggested when unit is installed closer than 15 ft to
quiet areas, bedrooms, etc.
Suggested when unit is installed between two houses less
than 10 ft apart.
Usage Guideline:
Suggested in the following applications:
Heat pump installations in heavy snowfall areas.
Heat pump installations in snowdrift locations.
Heat pump installations in areas of prolonged
subfreezing temperatures.
All commercial installations.
15. Thermostatic Expansion Valve (TXV) Bi--Flow
A modulating flow--control valve which meters refrigerant liquid
flow rate into the evaporator in response to the superheat of the
refrigerant gas leaving the evaporator.
Usage Guideline:
Required in all heat pump applications
16. Time--Delay Relay
An SPST delay relay which briefly continues operation of indoor
blower motor to provide additional cooling after the compressor
cycles off.
Note: Most indoor unit controls include this feature. For those
that do not, use the guideline below.
Usage Guideline:
213R

7
ELECTRICAL DATA
(VOLTAGE)
UNIT SIZE
--- S E R I E S
V/PH OPER VOLTS* COMPR FAN MCA
MIN
WIRE
SIZE{
MIN
WIRE
SIZE{
MAX
LENGTH
(FT)}
MAX
LENGTH
(FT)}
MAX
FUSE**
or CKT
BRK
AMPS
MAX MIN LRA RLA FLA 60°C75°C60°C75°C
(N) 018 --- A
208/230/1 253 187
41 9.0 0.5 11.70 14 14 166 158 20
(N) 024 --- A 54 11.3 0.8 14.80 14 14 131 125 25
(N) 030 --- A 72.5 14.8 0.8 19.20 12 12 161 154 30
(N) 036 --- A 88 17.0 0.9 22.10 12 12 140 133 35
(N) 042 --- A 104 21.2 0.9 27.40 10 10 181 172 40
(N) 048 --- A 137 21.2 1.2 27.60 10 10 179 170 40
(N) 060 --- A 148 28.9 1.2 37.30 8 8 207 197 60
(P) 030 --- A
208/230/3 253 197
63 10.4 0.75 13.75 14 14 66 63 20
(P) 036 --- A 77 11.3 0.9 15.03 12 12 96 92 25
(P) 042 --- A 88 13.4 0.9 17.65 12 12 82 78 25
(P) 048 --- A 91 13.78 1.2 18.43 10 10 125 119 30
(P) 060 --- A 123 18.7 1.2 24.58 810 146 89 35
(E) 036 --- A
460/3 506 414
39 5.5 0.5 7.38 14 14 247 235 15
(E) 042 --- A 44 6.4 0.5 8.50 14 14 214 203 15
(E) 048 --- A 46 7.1 0.6 9.41 14 14 193 184 15
(E) 060 --- A 62 8.6 0.6 11.35 14 14 160 152 15
* Permissible limits of the voltage range at which the unit will operate satisfactorily
{If wire is applied at ambient greater than 30°C(86°F), consult table 310---16 of the NEC (ANSI/NFPA 70). The ampacity of non---metallic---sheathed cable
(NM), trade name ROMEX, shall be that of 60°C (140°F) conditions, per the NEC (ANSI/NFPA 70) Article 336---26. If other than uncoated (no---plated), 60
or 75°C (140 or 167°C) insulation, copper wire (solid wire for 10 AWG or smaller, stranded wire for larger than 10 AWG) is used, consult applicable tables
of the NEC (ANSI/NFPA 70).
}Length shown is as measured 1 way along wire path between unit and service panel for voltage drop not to exceed 2%.
* * T i m e --- D e l a y f u s e .
F L A --- F u l l L o a d Am ps
LRA --- Locked Rotor Amps
MCA --- Minimum Circuit Amps
RLA --- Rated Load Amps
NOTE: Control circuit is 24---V on all units and requires external power source. Copper wire must be used from service disconnect to unit. All
motors/compressors contain internal overload protection.
A--WEIGHTED SOUND POWER (DBA)
UNIT SIZE --- SERIES STANDARD
RATING
TYPICAL OCTAVE BAND SPECTRUM (without tone adjustment)
125 250 500 1000 2000 4000 8000
018---A 75 52 59.5 64.5 71 67 61.5 54.5
024---A 76 52.5 63.5 69.5 72 67.5 64.5 59.5
030---A 76 52 64 70 71 68 66.5 65
036---A 76 53 69 66.5 69.5 66.5 63.5 62
042---A 76 57 65 68 72.5 67.5 64 59
048---A 76 57.5 65 68 70.5 69 64 60.5
060---A 77 61 62.5 70 72.5 70 67 60
A--WEIGHTED SOUND POWER (DBA) WITH SOUND HOOD
UNIT SIZE --- SERIES STANDARD
RATING
TYPICAL OCTAVE BAND SPECTRUM (without tone adjustment)
125 250 500 1000 2000 4000 8000
018---A 74 52.0 59.5 64.0 68.0 64.0 60.0 52.5
024---A 75 53.5 63.0 69.0 70.5 66.5 64.0 58.5
030---A 75 53.0 64.5 69.5 70.5 67.5 64.5 60.5
036---A 75 54.0 68.5 65.5 68.0 65.0 62.0 57.5
042---A 76 58.0 64.5 67.0 71.0 65.5 61.0 54.5
048---A 75 58.0 64.0 68.0 69.0 65.5 60.5 55.5
060---A 75 59.5 61.5 67.5 70.0 68.0 64.0 57.5
CHARGING SUBCOOLING (TXV--TYPE EXPANSION DEVICE)
UNIT SIZE---SERIES REQUIRED SUBCOOLING (_F)
018---A 11
024---A 11
030---A 9
036---A 11
042---A 13
048---A 13
060---A 11
213R

8
DIMENSIONS NOTE: Optional “G” dense coil guard shown.
213R

9
213RN(A,G) BALANCE POINT WORKSHEET
0.00
10.00 20.00 30.00 40.00 50.00 60.00 70.00 80.00
--100 1020304050607080
OUTDOOR TEMPERATURE, ºF
BUILDING HEAT LOSS, UNIT INTEGRATED
HEATING CAPACITY, MBTUH
0.0 2.9 5.9 8.8 11.7 14.6 17.6 20.5 23.4
kW
213RN(A,G)024A
FA4CNF024
213RN(A,G)030A
FA4CNF030
213RN(A,G)036A
FC4DNF036
A05007
213RN(A,G)042A FC4DNF042 213RN(A,G)060A FC4DNF060
213RN(A,G)048A FC4DNF048
BASED ON INDOOR ENT. AIR AT 70
ºF AND AT RATED CFM
213RN(A,G)018A
FA4CNF018
213R

10
COMBINATION RATINGS
Unit Size
--- S e r i e s Indoor Model Cooling Capacity
ARI Standard Ratings
Cooling Heating
Furnace ModelFactory
Enhance
Standard
Rating
SEER
TDR EER
High Temp Low Temp
HSPF
E
Capacity ECOP H Capacity HCOP
018---A
*FA4CN(F,C)018 17,100 TDR&TXV 13.00 10.80 18,000 3.52 10,500 2.34 8.0
FA4CN(F,C)024 17,200 TDR&TXV 13.00 10.80 16,000 3.30 10,500 2.34 7.9
FC4DNF018 17,500 TDR&TXV 14.00 11.70 17,500 3.80 10,100 2.52 8.5
FC4DNF024 17,600 TDR&TXV 14.00 12.00 15,400 3.60 10,000 2.56 8.5
FF1ENE018 17,100 TDR&TXV 13.00 10.80 18,000 3.54 10,500 2.36 8.0
FF1ENE024 17,300 TDR&TXV 13.00 10.80 15,600 3.32 10,500 2.38 8.0
FK4DNF001 17,500 TDR&TXV 14.00 12.00 14,600 3.48 9,900 2.54 8.4
FK4DNF002 17,700 TDR&TXV 14.00 12.50 14,600 3.58 9,900 2.58 8.6
CAR**1814A** 16,900 TXV 13.00 10.80 18,100 3.46 10,400 2.34 7.9
CAR**1814A** 16,900 TDR&TXV 14.00 11.70 18,000 3.70 9,800 2.46 8.2 315(A,J)AV036070
CAR**2414A** 17,400 TXV 13.00 10.80 15,700 3.34 10,500 2.40 8.1
CAR**2414A** 17,300 TDR&TXV 14.00 12.00 15,600 3.70 9,900 2.50 8.4 315(A,J)AV036070
CAR**2417A** 17,400 TXV 13.00 10.80 15,700 3.34 10,500 2.40 8.1
CAR**2417A** 17,300 TDR&TXV 14.00 12.00 15,600 3.70 9,900 2.52 8.4 355AAV042060
CAR**2417A** 17,400 TDR&TXV 14.00 12.00 15,600 3.70 9,900 2.52 8.6 315(A,J)AV048090
CNRV*1814A** 16,900 TXV 13.00 10.80 17,200 3.52 10,500 2.40 8.1
CNRV*1814A** 16,900 TDR&TXV 14.00 12.00 17,100 3.88 9,900 2.50 8.5 315(A,J)AV036070
CNRV*2414A** 17,400 TXV 13.00 10.80 15,700 3.44 10,500 2.40 8.2
CNRV*2414A** 17,300 TDR&TXV 14.00 12.00 15,600 3.84 9,900 2.52 8.5 315(A,J)AV036070
CNRV*2417A** 17,400 TXV 13.00 10.80 15,700 3.44 10,500 2.40 8.2
CNRV*2417A** 17,300 TDR&TXV 14.00 12.00 15,600 3.84 9,900 2.52 8.5 355AAV042060
CNRV*2417A** 17,400 TDR&TXV 14.00 12.00 15,600 3.84 9,900 2.54 8.5 315(A,J)AV048090
CNRH*2417A** 17,400 TXV 13.00 10.80 15,700 3.44 10,500 2.40 8.2
CNRH*2417A** 17,300 TDR&TXV 14.00 12.00 15,600 3.84 9,900 2.52 8.5 355AAV042040
CNRH*2417A** 17,300 TDR&TXV 14.00 12.00 15,600 3.84 9,900 2.52 8.5 355AAV042060
CNRH*2417A** 17,400 TDR&TXV 14.00 12.00 15,600 3.82 9,900 2.52 8.5 355AAV042080
CNRH*2417A** 17,400 TDR&TXV 14.00 12.00 15,600 3.84 9,900 2.52 8.5 315(A,J)AV036070
CNRH*2417A** 17,400 TDR&TXV 14.00 12.00 15,600 3.84 9,900 2.54 8.5 315(A,J)AV048090
CNRF*2418A** 17,400 TXV 13.00 10.80 15,700 3.44 10,500 2.40 8.2
CSRH*2412A** 17,400 TXV 13.00 10.80 14,800 3.26 10,500 2.42 8.0
CSRH*2412A** 17,300 TDR&TXV 14.00 12.00 14,800 3.62 9,900 2.52 8.5 355AAV042040
CSRH*2412A** 17,300 TDR&TXV 14.00 12.00 14,800 3.62 9,900 2.52 8.5 355AAV042060
CSRH*2412A** 17,400 TDR&TXV 14.00 12.00 14,800 3.60 9,900 2.52 8.5 355AAV042080
CSRH*2412A** 17,300 TDR&TXV 14.00 12.00 14,800 3.62 9,900 2.52 8.5 315(A,J)AV036070
CSRH*2412A** 17,400 TDR&TXV 14.00 12.00 14,800 3.62 9,900 2.52 8.5 315(A,J)AV048090
024---A
*FA4CN(F,C)024 22,600 TDR&TXV 13.00 10.80 23,800 3.52 14,400 2.36 7.9
FA4CN(F,C)030 22,800 TDR&TXV 13.00 10.80 22,600 3.46 14,400 2.38 7.9
FC4DNF024 23,000 TDR&TXV 14.00 11.50 23,400 3.70 13,900 2.48 8.3
FC4DNF030 23,200 TDR&TXV 14.00 11.50 22,200 3.66 13,900 2.52 8.4
FF1ENE030 22,600 TDR&TXV 13.00 10.80 23,600 3.52 14,400 2.36 8.0
FK4DNF001 23,000 TDR&TXV 14.00 11.70 22,600 3.66 13,700 2.48 8.3
FK4DNF002 23,200 TDR&TXV 14.00 11.70 22,600 3.78 13,700 2.54 8.5
FK4DNF003 23,200 TDR&TXV 14.00 11.70 20,800 3.60 13,600 2.54 8.5
CAR**2414A** 22,800 TXV 13.00 10.80 23,800 3.56 14,400 2.38 8.1
CAR**2414A** 22,800 TDR&TXV 14.00 11.50 23,800 3.72 13,700 2.46 8.3 315(A,J)AV036070
CAR**2417A** 22,800 TXV 13.00 10.80 23,800 3.56 14,400 2.38 8.1
CAR**2417A** 22,800 TDR&TXV 14.00 11.50 23,600 3.74 13,700 2.48 8.3 355AAV042060
CAR**2417A** 22,800 TDR&TXV 14.00 11.70 23,600 3.76 13,600 2.50 8.4 315(A,J)AV048090
CAR**3014A** 22,800 TXV 13.00 10.80 20,800 3.30 14,500 2.38 7.8
CAR**3014A** 22,800 TDR&TXV 14.00 11.50 22,000 3.58 13,700 2.48 8.2 315(A,J)AV036070
CAR**3017A** 22,800 TXV 13.00 10.80 20,800 3.30 14,500 2.38 7.8
CAR**3017A** 22,800 TDR&TXV 14.00 11.70 20,800 3.60 13,700 2.50 8.3 355AAV042060
CAR**3017A** 23,000 TDR&TXV 14.00 11.70 20,800 3.62 13,600 2.52 8.3 315(A,J)AV048090
See notes on pg. 17
213R