Bryant P474-0401RF Guide

Heat only, or Cool only
72 72
HEAT
Mo
I2:34 2 - Wire Operation
No Batteries Required
Simple, Single Setpoint
7 Day Programmable
4 Time Periods
Very Easy to Program
Large, Easy To Read Display
Thermoglow Backlight
Locking Keypad
Meets California Title 24 Residential
MODEL TSTATBBP2W01
PROGRAMMABLE DIGITAL
THERMOSTAT
Heating & Cooling Systems
USERS INFORMATION MANUAL
NOTE TO INSTALLER:
This manual must be left with the equipment user.

Table Of Contents
FRONT PANEL
DISPLAY
QUICK START Set the clock and go
BASIC OPERATION
PROGRAMMING Time Periods
ADVANCED SETUP
ABOUT ADVANCED OPERATION
WARRANTY
Page 1
CAUTION
Follow Installation Instructions before proceeding.
SET THERMOSTAT TO MODE “OFF” PRIOR TO
CHANGING SETTINGS IN SETUP OR RESTORING
FACTORY DEFAULTS.
2
3
5
6
8
12
16
19
TSTATBBP2W01
Residential Light Commercial Systems Carrier Corporation 4/01

Front Panel
Page 2
Liquid Crystal Display
with Thermoglow
Up/Down Buttons
On/Off Button
Outside Button
Heat or Cool Indicator
Heat = Red, Cool = Green
1
2
3
4
5
72 70
HEAT
Mo
I2:00
2
3
45
1

1
2
4
3
Mode Indicators
Selects the operation mode of the equipment.
HEAT - indicates the heat mode.
COOL - indicates the air conditioning mode.
OFF - indicates the entire system is turned off.
PROGRAM ON - indicates the stored program
is enabled to run. Page 6.
Clock with Day of the Week
Indicates the current time and day. This clock is
also used to program the time periods. Page 5.
Room Temperature Display
Indicates the current room temperature, or can
be configured to display the setpoint. Page 7.
Desired Set Temperature
Indicates desired room temperature(s). Page 7.
Display
Page 3
1
1
3
4
4
6
5
5
7
8
2
Night
MorningDayEvening
Am
Pm
SuMoTuWeThFrSa
Setup
Locked
Outside
Program On
ONOFF
COOL
HEAT
I2:00 88
88
88

5
6
7
8
Morning, Day, Evening & Night Indication
Indicates the program time period.
Page 8-11.
Setup Indication
Indicates the thermostat is in the programming
mode. Page 12.
Locked Indication
Locked appears after the right combination of
buttons are pressed, rendering the buttons
inoperative. Page 16.
Outside Indication
Outside temperature appears after pressing the
Outside button if the thermostat is connected
to an optional Outside Sensor.
Display
Page 4

During Setup & Programming:
Pressing the Mode button
selects different flashing items.
(Represented in dark black)
Pressing the Up and Down
buttons will modify the flashing
selection.
Press the On/Off button.
While holding the On/Off
press the Outside button
for 2 seconds to enter Setup
screens.
Press both On/Off and
Outside buttons as
above to return to
normal operation.
Quick Start Set the Clock and Go
Page 5
The thermostat is preprogrammed from the
factory to operate without the need for further
programming. To optimize the installation
of this thermostat follow the instructions
in the Advanced Setup section.
buttons.
To adjust the
clock or Day use
Press
I
I2:00
2
Su
OUTSIDE
OUTSIDE
ON/OFF
ON/OFF
ON/OFF

The HEAT setting indicates the
temperature the room has to
reach before the furnace will
turn on to heat the room.
OFF indicates the heating
system is turned off.
NOTE: The operating mode of this thermostat may be changed from the
factory default HEAT operation, to COOL operation in the Advanced Setup
Section.
In the following pages Cool operation may be substituted for Heat operation
if the factory default is changed in Advance Setup Step #3.
The Program On operating mode will be bypassed if the factory default is
changed in Advanced Setup, step #4.
Program On will activate the
stored timer operation.
(Morning, Day, Evening, Night)
Select Mode
Basic Operation
Page 6
Press
Press
70
I2:00
69
Su
70
I2:00
70
Su
Day
70
I2:00
Su
OFF
ON/OFF
ON/OFF

buttons.
Adjust the
desired Set Temperature
with
Pressing the up/down buttons in Heat or Cool will adjust only the H
Cool set temperature.
eat or
Select Desired Temperature
Page 7
Basic Operation
70 69
Pm
HEAT
Mo
I2:00
70
OUTSIDE
Outside
Temperature
Pressing the Outside button will display the
outside temperature. A subsequent press
of the Outside button will return the display
to the previous screen. Normal operation
will continue while the Outside temperature
is being displayed.
Press
OUTSIDE
This feature is only available if an
optional wired, or wireless Outside
Sensor is connected to the
thermostat.

Programming 4 Time periods
Page 8
Press
Press
Press
Press the On/Off button. While holding the On/Off,
press the Up button for 2 seconds to enter
time period programming.
Continued
Select the Day of the Week.
Adjust the start time for
Morning.
Adjust the heating setpoint
for Morning.
(35 - 99 )
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Mo
70
HEAT
Morning
Morning
Am
Am
Mo
Mo
6:00
6:00

Programming 4 Time Periods
Page 9
ON/OFF
Press
Press
Press
Continued
Adjust the start time for
Day.
Adjust the start time for
Evening.
Adjust the heating setpoint
for Day.
(35 - 99 )
ON/OFF
ON/OFF
Day
Am
Mo
8:00
Day
Am
Mo
HEAT
8:00
62
Evening
Pm
Mo
6:00