Bryant TSTATBBN2W01 Guide

Heat only, or Cool only
HEAT
72
72
2 - Wire Operation
No Batteries Required
Large, Easy To Read Display
Thermoglow Backlight
Keypad Lock
Meets California Title 24 Residential
USERS INFORMATION MANUAL
Heating & Cooling Systems
MODEL TSTATBBN2W01
PROGRAMMABLE DIGITAL
THERMOSTAT

Table Of Contents
FRONT PANEL
DISPLAY
BASIC OPERATION
ADVANCED SETUP
ABOUT ADVANCED OPERATION
WARRANTY
Page 1
CAUTION
Follow Installation Instructions before proceeding.
SET THERMOSTAT TO MODE “OFF” PRIOR TO
CHANGING SETTINGS IN SETUP OR RESTORING
FACTORY DEFAULTS.
2
3
4
6
9
12
TSTATBBN2W01
Residential Light Commercial Systems Carrier Corporation 4/01

Front Panel
Page 2
Liquid Crystal Display
with Thermoglow
Up/Down Buttons
OnO/ff Button
Outside Button
Heat or Cool Indicator
Heat = Red, Cool = Green
1
2
3
4
5
HEAT
72
72
5
1
2
3
4

Display
Page 3
OFF
COOL
88
HEAT
88
88
2
3
1
1
3
1
1
3
2
Mode Indicators
Selects the operation mode of the equipment.
HEAT - indicates the heat mode.
COOL - indicates the air conditioning mode.
OFF - indicates the entire system is turned off.
Page 6.
Room Temperature Display
Indicates the current room temperature.
Desired Set Temperature
Indicates desired room temperature(s). Page 7.

NOTE: The operating mode of this thermostat may be changed from the
factory default HEAT operation, to COOL operation in the Advanced Setup
Section.
In the following pages Cool operation may be substituted for Heat operation
if the factory default is changed in Advance Setup Step #3.
Basic Operation
Page 4
The HEAT setting indicates the
temperature the room has to
reach before the furnace will
turn on to heat the room.
The COOL setting indicates the
temperature the room has to
reach before the air conditioner
will turn on to cool the room.
OFF indicates both heating
and air conditioning
systems are turned off.
Select Mode
HEAT
74
72
COOL
72
72
OFF
72
Press
Press
ON/OFF
ON/OFF

buttons.
Adjust the
desired Set Temperature
with
Pressing the Up or Down buttons in Heat or Cool will adjust only the H
Cool set temperature.
eat or
Page 5
Basic Operation
Outside
Temperature
Pressing the Outside button will display the
outside temperature. A subsequent press
of the Outside button will return the display
to the previous screen. Normal operation
will continue while the Outside temperature
is being displayed.
Press
OUTSIDE
This feature is only available if an
optional wired, or wireless Outside
Sensor is connected to the
thermostat.
72
Select Desired Temperature
HEAT
72
72

Advanced Setup
Page 6
Press the On/Off button.
While holding the On/Off
press the Outside button
for 2 seconds to enter Setup
screens.
NOTE: Each step # is located at
the top right corner of the
display for easy reference.
OUTSIDE
i
HEAT
Select HEAT or COOL
operation.
COOL
HEAT
Adjust the deadband
from 1 - 6 degrees.
2
2
88
Select the cycles per
hour limit.
d=cycles per hour
limit defeated.
d1=d + defeat 5 min.
Compressor lockout,
lockout is for Cool
operation.
(d, d1, 2 - 6)
6
3
Cy
Press
Press
Press
Continued
ON/OFF
ON/OFF
ON/OFF
ON/OFF

Advanced Setup
Page 7
Select the display back-
light always On, or Off
after 8 seconds.
On
Off
Select thermostat
operation in degrees
Fahrenheit or Centigrade.
C
F
F
4
L I
5
ON
Press
ON/OFF
OUTSIDE
ON/OFF
Press the On/Off button.
While holding the On/Off press the
outside button to leave the Setup screens.
If no buttons are pressed, the display will
leave the setup screens after 60 seconds.

Advanced Setup
Page 8
Step # Description Range Factory Default
1 Operating Mode - Heat or Cool Heat / Cool Heat
2 Deadband or Temperature swing 1 - 6 2
3
4
5
Cycles per hour d, d1, 2 - 6 6
Fahrenheit or Centigrade F / C F
Thermoglow backlight Off / On On
Advanced Setup Table
OUTDOOR SENSOR
An outdoor temperature sensor may be connected to this thermostat. Totaline
offers wired or wireless models. Compatible models include: P474-0401RF/REC
& P474-0400.
Consult the remote sensor instruction sheet for wiring connections.

HEAT
72
72
About Advanced Features & Operation
Page 9
KEYPAD LOCK - To prevent unauthorized use of the thermostat,
the front panel buttons may be disabled. To disable, or
‘lock’ the keypad, press and hold in the On/Off button.
While holding the On/Off button in, press the Down button,
while holding the Down button in press the Up button. The
keypad is now locked.
Press all 3 for
Keypad Lockout
To unlock the buttons, again press and hold in the On/Off
button. While holding the On/Off button in, press the Down
button, while holding the Down button in press the Up button.
The keypad is now unlocked.
ON/OFF
FACTORY DEFAULTS - If, for any reason it is desirable to
return all stored settings back to the factory default
settings, press the On/Off button. While holding the On/Off
button in, press the Down button for 5 sec. All icons will
appear. Press and hold in the Outside button until Fd
appears. This resets all factory settings. To calibrate
room temperature, press the On/Off button once more.
At this point use the Up and Down buttons to calibrate
room temperature, if needed. Press the On/Off button to
return to normal operation. NOTE CAUTION ON PAGE 1.