Bryton Cardio 40 User manual

User’s Gu
i
de
40
AM

Cardio 40 User’s Guide2
EN
Cardio 40
AM
1
3
2
4
5
1Light / Power ( / )
Press and hold to turn the•
device on or o.
Press to turn on or o the•
backlight.
2Back ( )
Pr• ess to return to the
previous page or cancel an
operation.
In Training mode, press to•
pause or stop recording
log. While the recording
is paused, press again to
stop.
3OK (OK)
In Clock view, press to•
enter the menu mode.
In Menu, press to enter or•
conrm a selection.
When recording, press to•
mark the lap.
4Up (p)
In Menu, press to move•
up to scroll through
menu options. Press and
hold to fast scroll up
through menu options.
5Down (q/ )
In Menu, press to move•
down to scroll through
menu options. Press and
hold to fast scroll down
through menu options.
In meter view, press to•
switch meter screen
page.

Cardio 40 User’s Guide 3
EN
Getting Started
Turn On/O
Press and hold to turn the
device on or o.
Reset
To reset the device, press and
hold all three keys ( /OK/q) at
the same time.
Initial Setup
When turning the device on for
the rst time, the setup wizard
appears on screen. Follow the
instructions to complete setup.
1. Select the display language.
2. Select the unit of
measurement.
3. Enter your “user prole”.
It is recommended to input
the data. Data accuracy will
highly aect your training
analysis.
4. Read and accept the Safety
Agreement.
Connect, Sync, and
Charge
1. Connect the device to a
PC using the supplied USB
charging clipper.
2. Download the Bryton Bridge
2application at brytonsport.
com and sync with the
device.
AM
Keep the device connected to
the PC to charge the battery.
Attach the USB charging clipper
onto the device and plug the
other end to a PC.
Note:
For rst time use, charge the battery•
for about 3 hours.
Please send the watch back to local•
distributor for any battery issues.
Improper battery replacement may•
cause an explosion. When replacing
a new battery, use only the original
battery or a similar type of battery
specied by the manufacturer.
Disposal of the used batteries must
be carried out in accordance to the
regulations of your local authority.
For better environmental
protection, waste batteries
should be collected
separately for recycling or
special disposal.

Cardio 40 User’s Guide4
EN
Icons
icon Description
GPS Signal Strength
No signal
Poor *
Fair **
Good **
GPS Positioning Status
No signal (not
xed)
Weak signal
Strong signal
Heart Rate Sensor
Active
GPS Fixed
GPSGood
View Status Bar
icon Description
Training mode
Meter mode
Log Record in
Progress
Recording is
paused
Power Status
Full battery
/ Half battery
Low battery
Note:
Only the active icons are displayed on the screen.•
* Please go to an open area for better reception.
** When blinking, please wait until it stops blinking.
Battery level
GPS on/o status
Recording indicator
Meter mode
Sensors are successfully
linked to Cardio 40

Cardio 40 User’s Guide 5
EN
Clock View
AM
04:30 AM
Set Time
1. Press qto enter the menu mode.
2. Press p/qto select Settings > Watch
> Time > Set Time 1 or Set Time 2 and
press OK to enter its submenu.
3. Press p/qto select the desired setting
and press OK to conrm.
Set Alarm (Time1)
1. In Menu, press p/qto select Settings >
Watch > Alarm and press OK to enter its
submenu.
2. Press p/qto select the desired setting
and press OK to conrm.
Note: To enable the alarm, select Settings > Watch > Alarm > Switch > On.
Current date
Time 1
(local time)
Time 2
(alternate time)
Time
Set Time 1
Set Time 2
OFF
Current day
Alarm
Set Alarm:
AM 08:00
Switch:
ON
Reminder icon
Alarm icon

Cardio 40 User’s Guide6
EN
Exercise/Training
During exercise or training, Cardio 40 allows you to measure
and record your running activities and displays your current
performance.
Note: Displayed information varies on exercise mode and user preference.
Ready for Simple Training
1. Press qto enter the menu mode.
2. Press p/qto select Train & Test and
press OK to enter Training menu.
3. To set a simple workout, select To Plan
> Simple > By Time, By Distance, or By
Calorie.
4. Set the training target and press OK to
conrm.
Note: Select Yes to save the workout. To perform the workout, go to Train &
Test > My Workout.
5. Enter the workout name using the
on-screen keyboard.
When nishing the name, choose
END to save the workout name.
Simple
By Time
By Distance
By Calorie
Simple
By Time
By Distance
By Calorie
Yes
Save to my workout?
03:48 PM
Running
Train & Test
View History
Settings
01/04

Cardio 40 User’s Guide 7
EN
Customize Workouts
To set a customize workout, select Train & Test > To Plan >
Customize > Add New. Then set the training target and press OK
to conrm.
Note: If user does not enter the workout name, the system will automatically label
the le name according to the current date and time.
Simple
Interval
Customize
To Plan
Customize
Add new step
Duration
Target
OK
Work
Exercise
Reminder
My lap
96~110 bpm
Time
Duration
Customize
Save
Yes
Save to My Workout?
Exercise
Reminder
My lap
96~110 bpm
Time
Customize
Save
Duration
Target
OK
Work
Customize
Work 1
6’0” 159~171 bpm
Add new step
WKT 001
END
Name
OK OK
OK
OK
OK OK
OK
OK
q
q
OK

Cardio 40 User’s Guide8
EN
Bryton Test & Workout
1. In Menu, press p/qto select Train & Test and press OK to enter
Training menu.
2. Press p/qto select Bryton WKT or Bryton Test and press OK
to enter its submenu.
3. Press p/qto select the desired
setting and press OK to conrm.
Bryton WKT
20' in Z 1-2
20' Z3
40' easy run
Tempo run
Bryton Workout
Bryton Test
LTHR
MHR
3km Race
5km Race
Bryton Test
r
p
m
Note: When the icon appears on the screen,
press pto skip the current Interval.
Interval Workouts
To set an interval workout, select Train & Test > To Plan >
Interval. Then set the training target and press OK to conrm.
Simple
Interval
Customize
To Plan
Interval
Warm up
10:00
Work:
06:00 162~172 bpm
Interval
Warm up
10:00
Work:
06:00 162~172 bpm
00:10’:00”
Time
Interval
Recovery
02:00 120~150 bpm
Repeat
2
Interval
Cool down
10:00
Save
p
q
p
q

Cardio 40 User’s Guide 9
EN
Start / Pause / Stop Exercising/Training
Press• OK to start recording the log.
Press• to pause the recording and
press again to stop the recording.
Note:
During exercising/training, press and hold• to
enter Shortcut menu.
When recording, press• twice to stop recording.
My Lap
To start a Lap workout, select Settings > Exercise > My Lap >
Distance or Location and press OK. Then set the training target
and press OK to conrm.
Mark Lap
Start an activity rst by pressing OK. While recording, press OK to
mark lap. When using Lap, the Lap screen will be displayed while
you are doing exercise or training.
View History
1. In Menu, press p/qto select View
History and press OK to conrm.
2. Use p/qto view your history. Choose
More for more details.
r
p
m
Yes
Do you want
to stop?
5min/km
00:06:00 run
12 km
512 kcal
5 laps
2/5
More
12/25 12:23

Cardio 40 User’s Guide10
EN
Delete All Exercise/Training Info
1. In Menu, press p/qto select View History and press OK to
conrm.
2. Press p/qto select Delete All and
press OK to enter its submenu. A
“Please backup data rst. Erase?”
message appears on the screen. To
delete the data, press p/qto select
Yes and press OK to conrm.
Delete
Yes
Please backup
data first. Erase?
Setting Reminder
1. In Menu, press p/qto select Settings > Exer. Remind > Time,
Distance, Stride Rate, HR, or Pace and press OK to enter the
submenu.
2. Press p/qto set the desired setting and press OK to conrm.
Exercise
Reminder
My lap
96~110 bpm
HR
Exer. Remind
Exercise
Reminder
My lap
96~110 bpm
90
Min
Exercise
Reminder
My lap
96~110 bpm
180
Max
Exercise
Reminder
My lap
96~110 bpm
5
Max
Exercise
Reminder
My lap
96~110 bpm
7
Min
Exercise
Reminder
My lap
96~110 bpm
Pace
Exer. Remind
Exercise
Reminder
My lap
96~110 bpm
Time
Exer. Remind
p
q

Cardio 40 User’s Guide 11
EN
Link Sensors
Use the Link setting to pair sensors to Cardio 40.
1. In Menu, press p/qto select Settings >
Sensors > Heart Rate and press OK to
enter its submenu.
2. Press p/qto select More and press OK
to enter the selected sensor submenu.
3. When the sensor is successfully
connected, the sensor ID will be
displayed on the screen.
Verify that the sensor ID is correct.
Note: The information on the sensors ID are included in the package.
4. Press p/qto select the desired option
and press OK to conrm.
Rescan• : rescan to detect the sensor.
TurnO• (*only if the device has
paired with the sensor): disable the
sensor.
Customize the Display Settings
1. In Menu, press p/qto select Settings >
Exercise > Meter > Meter >
Meter 1, Meter 2, Meter 3, or Meter 4
and press OK to enter its submenu.
Note: Lap only has two options (Meter 1 / Meter 2).
2. Press p/qto select the number of data elds and press OK to
conrm.
Sensors
Heart Rate
Heart Rate
Status: active
ID: xxxxxxxx
More
Sensor
Rescan
Turn Off
Meter
Meter 1
Meter 3
Off
On
Meter 2
Off

Cardio 40 User’s Guide12
EN
3. Press p/qto select the item eld that you want to customize,
and press OK to conrm the selection.
4. Press p/qto select the desired setting and press OK to conrm.
Note: After the setting is complete, the Lap screen appears only when Lap
function starts.
Personalize User Prole
1. In Menu, press p/qto select Settings > Prole > User and
press OK to enter its submenu.
2. Press p/qto select the setting that you want to change and
press OK to conrm.
Change Backlight O Settings
1. In Menu, press p/qto select Settings >
General > System > Backlight o and
press OK to enter its submenu.
2. Press p/qto select the desired setting
and press OK to conrm.
Enable Key Tone / Alert
In Menu, press p/qto select Settings > General > System > Key
Tone or Alert and press OK to enter its submenu. Then press p/q
to select ON and press OK to enable the setting.
Note: When the alert is set OFF, the sound will go o during workout and free
exercise.
Set the Unit/Language
In Menu, press p/qto select Settings > General > System > Unit
or Language and press OK. Then press p/qto select the desired
setting and press OK to conrm.
Backlight off
5 seconds
15 seconds
30 seconds
1 Mins

Cardio 40 User’s Guide 13
EN
View GPS
In Menu, press p/qto select Settings > General > GPS and press
OK.
O• : disable the GPS.
FullPower• : GPS is set on and provide more accurate position
but consume more power.
PowerSaving• : GPS is set on. The GPS positioning will be less
accurate but battery hours can be last longer.
Specications
Item Description
Display 1.4” Mono LCD
Physical size 42.9 x 48.4 x 17.7mm
Weight 48 g
Operating
temperature -10°C ~ 50°C
Battery charge
temperature 0°C ~ 40°C
Battery life
Up to 14 days in clock mode
Up to 8 hours in training mode in open-sky
environment
GPS Integrated high-sensitivity receiver with
embedded antenna
RF transceiver 2.4 GHz ANT+ transceiver with embedded
antenna
G-Sensor 3-axis acceleration sensor
*Design and specications are subject to change without prior notice.