Bsmarthome SH-01 Series User manual

SH-01-002
Installation Guide

2/ 31
TABLE OF CONTENTS
Introduction .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .............4
Getting Started ... ... ........ ........ ........ ........ ........ ........ ........5
Installing the Thermostat ..... ..... ..... ..... ..... ..... ....... ...........6
Disassembly ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..........6
Thermostat Location ... ..... .................... ... ......................7
Mounting the Subbase . ..... ..... ..... ...... ..... ..... ..... .... . ..7
Installing the thermostat ....... ..... ... ................8
Terminal Designations ....... ......... ........ ...... ... ................9
System wiring diagram........... . ........ ........ ........ .........11
Typical System Wiring Diagrams ...... ...... ...... ...... ... .........12
Heat only (electric,gas) ....... ...... …………………........ ........ ..12
Cool only............... . . . . . . . . . . . . . . . . . . . . ……………. . .....13
Standard Heat-Cool, 1 speed fan O/B = 'B'. . . ………… . . . .. .14
Standard Heat-Cool, 1 speed fan O/B = 'O'... . . ………... . . ...15

3/ 31
Standard Heat-Cool, 2 speed fan O/B = 'B'.... . . …….... . . ...16
Standard Heat-Cool, 2 speed fan O/B = 'O'..... . . . . . ...17
Standard Heat Pump, 1 speed fan O/B = 'B'. . . . . . . . .18
Standard Heat Pump, 1 speed fan O/B = 'O'. . . . . . . . .19
Standard Heat Pump, 2 speed fan O/B = 'B'. . . . . . . . .20
Standard Heat Pump, 2 speed fan O/B = 'O' . . . . . . . . .21
Selecting Programmable or Non-programmable Op .22
Installer Setup Menu .. . . . . . . . . . . . . . . . . . .. . . . . . . .. . 23
Entering the Installer setup Menu . ..... ..... ..... . . .... . .....23
Selecting System Mode ... ...... ...... ...... ...... ...... ... .......23
Selecting Fan Speed ......... ..... . . . . . . . . . . . . . . . . . . ...24
Selecting O/B Options ........... ......... . . . . . . . . . . . . . . ...24
Selecting Fan Mode Option ...... ....... . . . . . . . . . . . . . ....24
Selecting the Heating Setpoint Limit ....... .......... . . . . . ...24
Selecting Differential Option ..... . . ... . . . . . . . . ....25
Display Functions .... .. . . . . . . . . . . .. . . . . . . . . . .............27

4/ 31
Specifications ...... ... ........... ............ ................ ............29
INTRODUCTION
The SH-01 SERIES is a feature-rich touchscreen
thermostat that can be powered or hardwired to the HVAC
equipment. Using a common sense approach to the installation
will ensure this product is installed properly and to the
customer’s satisfaction. Please take time to read and
understand this manual so that installation and testing is
performed in an efficient manner.
This manual is to be used in conjunction with the supplied User
Manual.Although great care has been taken in thepreparation of
this manual, we takes no responsibility for errors or omissions
contained herein. It is the responsibility of the installer to ensure
that this thermostat and the equipment connected to it operate in
a safe and efficient manner. Due to ongoing product

5/ 31
improvements, We reserves the right to change the
specifications of the SH-01 SERIES thermostat or its
components without notice.
GETTING STARTED
As with any HVAC project, careful installation is the key to
a successful outcome. Time taken during the installation
process will be rewarded with fewer call-backs. The steps
required to install the SH-01 SERIES thermostat are as follows.
1. Read and understand this Installation Manual and User
Manual.
2. Mount and wire the subbase.
3. Set the system to match the equipment application
4. Power the thermostat
5. Set the Advanced Installer settings.
6. Test the thermostat.

6/ 31
INSTALLING THE THERMOSTAT
DISASSEMBLY
There are two release slots located on the bottom of the
thermostat. Gently push the flat blade of a small screwdriver into
one slot at a time and pry upward until the catch disengages.
Carefully swing the thermostat upward and away from the
subbase. (Figure 1)

7/ 31
THERMOSTAT LOCATION
The SH-01 SERIES should be installed in a location that
represents the ambient space temperature. Do not install the
thermostat in an area where drafts are present, near the floor,
behind doors or on an external wall. Avoid placing the
thermostat in areas where the air movement is limited, affected
by direct sunlight or other areas not typical of the temperature in

8/ 31
the space.
MOUNTING THE SUBBASE
When mounting the SH-01 SERIES subbase, be aware that
drafts may travel down wall cavities and enter the back of the
thermostat through the control wire hole in the wall. It is
important to seal the hole to prevent any drafts that might affect
the internal temperature sensor.
INSTALLING THE THERMOSTAT
Pull the control wires through the large opening in the thermostat
subbase. Next, level and mount the subbase on the wall using
the supplied anchors and screws. (Figure 2)
Do not over tighten the mounting screws as the subbase
may warp causing the improper seating of the thermostat

9/ 31
connecting pins to the terminal blocks.
Use a properly sized screwdriver and back each screw terminal
out (counter clockwise) before landing each wire to its dedicated
terminal. Do not over tighten the terminal screws. Check to
ensure that all wires are landed correctly and dressed properly
to prevent any shorts. Refer to Typical SystemWiring Diagrams
in this manual for proper wiring.
TERMINAL DESIGNATIONS
TERMINAL
DESIGNATION
Y1/W
First Stage Cool or First Stage Compressor
O,B
Reversing Valve
W1
First Stage Heat/Auxiliary/Emergency Heat
G,GL
FAN LOW SPEED

10 / 31
GH
FAN HIGH SPEED
R
24 VAC Hot
C
24 VAC Common
S2
Outdoor Sensor
SC
Sensor Common
S1
Indoor Sensor
A
Modbus RS485+
B
Modbus RS485-