Bticino 3527 User manual

1
3527
BT00099-b-EN
Radio remote control 6 channels
Description
This remote control is a transmitting radio device that can drive the radio actuators item
F470/1, F470/2, 3526, 3526/10 and 3526/16; when used in conjunction with receiving
interfaces HC/HS4575 and L/N/NT4575N, it can also be used to control devices of the
MY HOME system. This remote control has six radio channels and six customisable keys
which are back-lit and emit a sound when selected.
The remote control can also be used as a ashlight. There is an orange LED which
indicates that the radio transmission has occurred after pressing a key; if this indicator
turns red, it means that the batteries are dead and must be replaced.
Technical data
Power supply: 2 AA 1.5 V pen batteries
(not provided, min. duration: 3 years)
Operating temperature: 0 – 40 °C
Radio frequency: 868 MHz
Range: 100 m in free eld
(metal and reinforced concrete walls reduce the range)
Type of modulation: FSK
Torch function:
When you press keys 5 and 6, the remote control will act as a ashlight.
Warning, in this mode the duration of the battery is sensibly decreased.
Key 6
Key 5
LED
key 1
key 2
key 3
key 4
key 5
key 6
05/06/2012

2
3527
BT00099-b-
1234
Switch Position Operating mode
Switch 1 1 2 3 4
Up
Key lighting = ON
It lights up when the remote control key is pressed.
1 2 3 4
Down
Key lighting = OFF
It does not light up when the remote control key is pressed.
Switch 2 1 2 3 4
Up
Audible signal = ON
An audible signal is emitted when a key is pressed.
1 2 3 4
Down
Audible signal = OFF
No audible signal is emitted when a key is pressed.
Programming
To associate a dierent control to each of the alarm radio remote control channels, follow
the procedure below:
1) Press the interface radio programming pushbutton, congured in self-learning
mode, for 3 seconds: the red LED will turn ON steadily; release the pushbutton.
2) Within 20 seconds press the key of the remote control you want to program; the red
LED will begin to ash, hence indicating the activation of the programming mode.
3) Within 5 minutes, set the function you want to associate to the remote control key
using the actuator and/or corresponding control; the red LED will start ashing
quickly for about 2 seconds, thus indicating that the programming has been
completed.
4) You can repeat 1), 2) and 3) for all keys, even for a key that has already been
associated (in case you want to change it). A maximum of 24 self-learning
operations are possible (e.g. 4 remote controls item 3527).
To cancel the programming of one of the remote control keys, follow the procedure
below:
1) Press the programming pushbutton on the radio interface for at least 8 seconds
(after 4 seconds the red LED will turn ON steadily and then after another 5 seconds it
will turn OFF). Release the key. The red LED will turn ON again steadily.
2) If you want to cancel the programming condition of a key, press it on the remote
control within 20 seconds; the red LED will start ashing quickly for about 2 seconds,
thus conrming the cancellation.
3) From now on, the cancelled key will no longer activate any control until it is
re-programmed.
To cancel all programming conditions of the interface simultaneously, press the
programming pushbutton for about 12 seconds: the red LED will turn ON steadily
after 3 seconds; after another 5 seconds, it will turn OFF and after another 4 seconds
it will start ashing quickly for about 2 seconds, thus conrming the cancellation of all
programming conditions.
Release the key. Here you can completely reset the device by cancelling both the
associated radio codes and the controls associated to the various remote control keys.
Choose the level of the key audible signal:
1 - Move switch no. 4 to programming mode (UP).
2 - Hold down keys 1 and 3 simultaneously; after 2 seconds, keys 1 and 2 will light up.
3 - Press one of the lit keys to listen to the audible signal associated to it (key 1 higher
level).
4 - Hold down the key corresponding to the required level for more than 2 seconds.
5 - The level will be stored when an audible signal is emitted and when the key starts
ashing.
6 - Move switch no. 4 to normal operation mode (DOWN).
Conguration
To congure the remote control, it is not necessary to use traditional congurators:
Switches are used instead as indicated in the following table. To access the switches
remove the upper part of the remote control.
NOTE: Switches 3 and 4 must be left with the factory settings; switch no. 4 is used to set
the volume level of the audible signal of the keys, and to change the key scanning time
for the disabled function.
Radio remote control 6 channels
EN 05/06/2012

3
3527
BT00099-b-
Remote control functions for disabled people
The radio control is provided with a 3.5 mm standard mono jack input for connecting a
detector (for disabled people) and a screw connection for installation on wheelchair or
on bedside.
Thanks to signals issued by an external sensor, the main functions of the remote control
can also be recalled by a disabled person (control devices that enable to recover the
residual capacity of movement of a disabled person).
SCANNING OF KEYS - the rst signal from the external sensor starts the remote control
keys scanning sequence; the key reached by the scanning sequence may be identied by
a luminous and/or audible signal.
KEY SELECTION - the second signal from the sensor stops the scanning sequence when
the selected key is reached.
CONTROL ACTIVATION - the third signal from the sensor corresponds to a standard
pressure of the selected key. A short pressure corresponds to the key being pressed for a
short time, and then released; in case of extended pressure, the remote control will wait
for a fourth signal from the sensor, which will be interpreted as the key being released.
The time between the third and the fourth signal is interpreted as an extended pressure.
The scanning time for each individual key may be changed whilst in programming
mode.The remote control is sold factory set with a standard scanning time of 1 second.
1 - Move switch no. 4 to programming mode (UP).
2 - Press keys 1 and 6 at the same time for at least 2 seconds; the rst four keys light up.
3 - Press one of the lit keys to perform a scanning test to ascertain the associated
time. Scanning times are as follows: Key 1 = 2 sec., Key 2 = 1 sec., Key 3 = 0.5 sec.,
Key 4 = 0.3 sec.
4 - Press and hold down the key corresponding to the desired time for at least
2 seconds.
5 - The successful completion of the programming procedure is conrmed by the
pressed key ashing
6 - Move switch no. 4 to normal operation mode (DOWN).
jack input
screw connection
Radio remote control 6 channels
EN 05/06/2012