Cattron S Series User manual

Quick Start Guide
S-Series | S32, S41 & 11R
1. Wire Your Machine Control Unit
The MCU terminaland pin numberingof each relative to the OCU
buttons are identifiedin the system configurationdrawing provided
with your system.
1. The implementationof an appropriatemain line contactorpower
circuitis required using K18 and K19 to maintainthe machine
power and possibly K16 to reset the machine–can also be done
via local reset.
2. Connect power and ground (per system specification)to J1 via a
local disconnect switch.
3. If using an external antenna, make sure to turn the adjacent dip
switch on.
4. Check the wiring and turn on the MCU power. The MCU status
LEDs two power green, Heartbeat flashing red and status amber
will energize if all is OK , the relays K18 and K19 will energize
when the OCU is linked.
2. Install the Batteries
Rechargeable OCUs have tamperproof
screws on the battery cover. Disposable
battery (AA type) OCUs have cross head
screws on the battery cover.
3. Turn On the OCU
1. Press the ON button. The
OCU will wake from sleep to
a fully tested PASSIVE non-
transmittingmode.
2. You will see all LEDs flash
briefly.
3. The center status and right-
hand LEDs 1 and 2 will then
be illuminated.
ON
2nd
1st
4. Move to Active Mode
NB: S-Series OCUs must have completed the Association process with its target
MCU (this only needs to be done once, see next page)
From Passive Mode, the OCU can be moved into Active mode.
1. Press the stop switch and then press the on switch within 3 seconds.
2. The status E-stop LED will now flash showing it is transmitting.
3. The OCU is now operative, and the target machinewill be under direct control.
4. To shut the system down Press the Stop Switch.
5. If the OCU is left in Passive mode, it will power down after 3 minutes.
Nimble: 9M60-9061-A003-EN| May 2022
If using an external
antenna, connect here
and turn ON the adjacent
DIP switch
K18
K19 RF
Module
K16 FUSE

5. Associating an OCU with an MCU
1. For a new OCU that has never been associatedwith an MCU, the followingAssociationprocess will
need to be done once.
2. If possible, press and hold the MCU button shown below. If this is not possible the OCU MUST be held
closer to the antenna of the MCU - to ensure it is connected to that OCUrather than any other MCU. If
necessary, move other MCUs away from the machineto be connected to, in order to ensure it connects
to that intended MCU. The logic is: IF an MCU’s button is pressed, connect to that MCU, IF NOT connect
to the MCU with the strongest signal.
3. Withthe MCU powered up and the OCU in Passivemode (Refer to Step 3), press MCU button (if
possible)and then immediately, for the type of OCU shown, press and hold the two starred buttonsfor
10 seconds, until the center StatusLED goes Blue. Release all buttons and wait a few seconds for
LED1 to flash Green. The OCU and MCU are now associated.
4. If LED1 does not flashGreen or flashes Red, repeat the associationprocess.
NB:
•An OCU cannot be associated with morethan one MCU.
•An MCU can be associated with up to 8 OCUs.
•However, if the MCU has already been associated with 8 OCUs, it will not be possible to associate it with
any more OCUs until the existing associationshave been cleared, this is done by pressing the button
shown for more than 20 seconds.
When the associationprocess has been completed,verify that the OCU is controllingthe intended
MCU before putting to work.
ConfigurationSheets and Manuals Are Available at Cattron.com
PRESS
K18
K19 RF
Module
K16 FUSE
Nimble: 9M60-9061-A003-EN| May 2022