BullFrog FROGswing OD2216 User guide

ASSEMBLY AND INSTRUCTION MANUAL
MODEL OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
www.bullfrog-design.com
Rocking frame: matt black fine structure
powder-coated
Rocking frame: fig. with sun canopy and
weather protection (Ecru), opened
Rocking frame: fig. with sun canopy and
weather protection (Ecru), closed
Fig. OD FROGswing with sun canopy (Ecru)

Assembly instructions, rocking frame OD FROGswing:
OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
1x Roof frame
1 x Base frame
1 x Strut
front side,
le
1 x Strut
back side,
le
1 x Strut back
side, right
14 x Stiening
Scope of delivery:
1 x Roof frame (1)
1 x Base frame (2)
1 x Strut front le (3)
1 x Strut front right (4)
1 x Strut back le (5)
1 x Strut back right (6)
14 x Stiening (7)
16 x Oval-head screw (8)
28 x Oval-head screw (9)
ATTENTION! To ensure secure assembly, please observe the individual steps of instruction!
The frame should always be mounted in pairs (2 persons)!
1. Unpack the individual parts of the rocking frame, place them in front of you and check the packaging for
completeness.
1
2
3
98
7
7
7
7
7
7
77
7
77
7
7
77
4
6
5
1 x Strut front
side, right
Views, ready-mounted frame:
View of front side View of back side
Front side,
le
Front side,
le
Back side,
le
Back side,
le
Front side,
right
Front side,
right
Back side,
right
Back side,
right

OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
Front side
le
Back side
le
Front side
right
Back side
right
2. Insert the struts into the respective mounting brackets on the base frame. Pay attention to the marking
(see fig. 1 & 2).
Fig. 1
Strut at the front side, le:
marked by "VL" at the lower end of the tube.
Brace at the front side, right:
marked by "VR" at the lower end of the tube.

OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
8 (M6 x 16)
Fig. 2
Strut at the back side, le:
marked by "HL" at the lower end of the tube.
Brace at the back side, right:
marked by "HR" at the lower end of the tube.
3. Now screw in 1 screw from each side through the holes in the struts into the
threads of the struts (4 x 2 screws).
Do not tighten them completely yet.

OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
(A)
front side
front side
4. Now tilt the frame assembly backwards. Use a suitable support to avoid damaging the frame and the floor.
5. Now put on the roof by pushing the respective pipe sockets of the roof frame onto the struts. Make sure that the smaller
distance between the swing crossbar and the frame (A) is at the front.
Unscrew the adjustable feet for the moment Screwing the roof frame
6. First screw the roof frame hand-tight to the 4 struts.
7. Info: Adjustable feet are already pre-assembled. These can usually be adjusted to compensate for uneven floors. First
turn them to the highest position (all the way down).
8 (M6 x 16)

OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
AB
28 (M6 x 25)
8 x
View, front side
Front side,
le
Back side,
le
Front side,
right
top = inside
6 x
bottom, outside
Back side,
right
8. Now set the frame upright again.
9. Mount the stieners. Screw them (14 pieces) hand-tight to the frame with 2 screws each.
When all stieners are in place, all screws must be tightened in assembly order.

OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
Assembly, rocking joint (le/right) for functional armchair OD ROCKfrog 180F/181F/182F/183F:
Suspension, right:
Suspension, le:
Suspension in the centre:
Cap nut
Washer
Frame
Screw
Teeth washer
Washer
Cap nut
Washer
Screw
Rocking joint
Teeth washer
Washer
Screw both rocking joints into the frame at the desired position. Use 2
screws (M8 x 60) each side. Observe the sequence.
Cap nut
Teeth washer
Washer
Screw M8 x 60
Frame
Washer
Rocking joint

OD2216 FROGswing
© 2022 K URT BEI E R &KATI QU I N G E R
Assembly, rocking joint (le/right) for functional sofa OD0821 ROCKfrog 200F/230F and
model OD2210 Mon Amour:
Suspension, right:
Suspension, le:
Cap nut
Washer
Screw
Rocking joint
Teeth washer
Washer
Screw both rocking joints into the frame at the shown position. Use 2
screws (M8 x 60) each side. Observe the sequence.
Cap nut
Washer
Frame
Screw
Teeth washer
Washer
Cap nut
Teeth washer
Washer
Screw M8 x 60
Frame
Washer
Rocking joint