Bunn ICB SH User manual

BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: [phone] FAX: [phone]
www.bunn.com
55227.0000A 07/18 ©2018 Bunn-O-Matic Corporation
ICB SH
ICB SH TWIN
Faucet Side Car Relocation
Instructions
TO BE PERFORMED BY QUALIFIED PERSONNEL
These instructions are intended for relocating the facuet side car on an ICB SH brewer. Ensure all tools are present before
performing the installation.
WARNING: Disconnect the brewer from the power source before performing the procedure. Ensure the
water is drained from the tank and be aware that many internal parts can be extremely hot; allow contents of
tank to cool before proceeding.
Note: If technical assistance is needed, please call 1-800-286-6345
Tools Required:
8/32 socket/wrench
Flat Blade Screwdriver

• Disconnect power to the brewer.
• Remove the screws that secure the front
panel to the brewer (6 screws).
STEP 1
• Carefully remove the front panel of the
brewer.
STEP 2
ICB SH Faucet Side Car Installation Instructions
• Remove the three screws that secure the
cover to the faucet side car.
• Remove the cover.
STEP 3
• Open the faucet handle to drain water from
the tank. Keep the faucet handle open until
water is no longer dispensing.
• Remove the hose snap clamp that secures
the tube to the faucet shank.
• Carefully remove the hose from the faucet
shank.
STEP 4
• Remove the two 8/32 nuts, two washers
and base screw from the faucet side car.
• Remove the black silicone grommet.
STEP 5
• Completely remove the faucet side car,
spacer and plate assembly from the left
side of the brewer.
STEP 6
Remove Cover
Remove Hose Snap
Remove Tube
Remove Nuts ,
Washers, Screws
& grommet
Spacer
Plate Assembly
Faucet Side Car

• Remove the plastic badge from the right
side of the brewer.
• Install the plastic badge on the left side of
the brewer to cover the panel holes.
• Install the base screw that was removed
in step 5.
STEP 7
• Remove the snap-in fastener from the
faucet side car and place into the hole
directly above as shown.
STEP 8
ICB SH Faucet Side Car Installation Instructions
• Place the plate assembly into the
uncovered holes on the inside of the right
panel.
• Place the spacer on the outside of the
right panel on the plate assembly.
STEP 9
• Remove the base screw on the right side.
STEP 10
• Align the faucet side car to the right side
of the brewer.
• Secure the faucet side car using the
washers and screws that were removed in
step 5.
STEP 11
• Insert the black grommet into the large
tubing hole. This is the same grommet
removed in step 5.
• Secure the base screw to the faucet side
car.
STEP 12
Plastic Badge
Secure
Remove
Fastener
Insert
Fastener
Plate Assembly
Spacer
Remove Base Screw
Align
Secure with
Washers &
Screws
Grommet

• Loosen the faucet nut to rotate the faucet
handle facing upwards.
• Route the faucet tube through the right
side panel.’
• Ensure there are no kinks in the tubing.
STEP 13
• Attach the faucet tube to the faucet shank.
• Secure the tube to the shank using the
hose snap that was removed in step 4.
STEP 14
ICB SH Faucet Side Car Installation Instructions
• Secure the cover to the faucet side car
using the screws that were removed in
step 3.
STEP 15
• Place the front panel on the brewer.
STEP 16
• Secure the front panel to the brewer using
the screws removed in step 1.
STEP 17
• Faucet side car relocation is complete.
STEP 18
Position Upright
Route Tube
Connect to
Shank
Secure with Clamp