Bunn Soft Heat Brewer & Server User manual

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation
Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation

Soft Heat®Brewer & Server
Use & Care Instructions
Slide the funnel into the
funnel rails of the brewer.
The display will read
NOW BREWING with the
remaining brew time.
The word DRIPPING will
read on the display.
Insert a BUNN filter into a
clean brew funnel.
For two hopper grinders,
select coffee type by
pressing “RIGHT” or
“LEFT” hopper.
If grinding fresh coffee,
place funnel in grinder.
Place an empty server
under the funnel. Rotate
handle forward to lock
the lid.
Press the GRIND button to
fill the funnel.
Press and release the
“ENABLE BREW” button.
Press the Batch Size button
according to the amount of
coffee in the filter.
Press the assigned BREW
button (A, B, or C).
When dripping has stopped,
discard the used grounds
and filter.
Clean and Sanitize the
funnel.
Gently shake funnel to
spread the grounds evenly.
If using pre-ground coffee,
simply pour fresh coffee
into filter.
Disassemble and thoroughly
rinse the sprayhead. The holes
must be open and clear of any
mineral deposits.
Once a week: Remove the
sprayhead by turning in a
counter-clockwise direction.
Re-assemble the
sprayhead and install
it onto the brewer.
Use the long end of the
sprayhead cleaning tool
to clean the sprayhead
outlet fitting.
Cleaning the Brewer
Brewing Coffee
Every Day: Wipe the
spreayhead panel and the
entire outside surface of
the brewer with a clean
damp cloth.
Page 1 of 2
54503.0000A 09/17 ©2017 Bunn-O-Matic Corporation