Burk Plus-X 600 User manual

Plus-X 600
Installation and Operation Manual

Copyright © 2012 Burk Technology, Inc.
Rev. B
Table of Contents
Introduction ................................................................................................................................ 1
Compatibility .............................................................................................................................. 1
Unpacking.................................................................................................................................. 2
Front Panel Indicators................................................................................................................ 2
Hardware Configuration ............................................................................................................. 2
Installation.................................................................................................................................. 4
Software Configuration............................................................................................................... 5
Uploading New Firmware........................................................................................................... 7
Troubleshooting ......................................................................................................................... 8
Getting Help............................................................................................................................... 8
Warranty .................................................................................................................................... 8
Appendix A: Specifications......................................................................................................... 9

Plus-X 600 Installation and Operation Manual Rev B
1
Introduction
The Plus-X 600 is a versatile I/O solution for the ARC Plus, providing 16 status inputs, 8
metering inputs and 6 raise/lower command pairs. The Plus-X 600 communicates with the ARC
Plus via LAN/WAN, allowing installation anywhere a network connection is available.
The Plus-X 600 is part of the Plus-X family of Ethernet I/O products designed for the ARC Plus.
Installation Note
Even though you may operate the ARC Plus and Plus-X 600 on different subnets, Burk
Technology strongly recommends installing the Plus-X 600 on the same LAN as the ARC Plus.
In a network failure, an ARC Plus can only continue to monitor and control a Plus-X device on
the same LAN. If the network link between the units is not available, ARC Plus macros, alarm
monitoring and telephone control will be unavailable for the Plus-X device.
Before you Begin
Before installing the Plus-X 600, please have the following network settings ready:
A static IP address for the Plus-X 600
The IP address of your ARC Plus
The subnet mask and gateway address for your LAN
Compatibility
Before installing the Plus-X 600, please verify that the ARC Plus firmware, AutoPilot® 2010
software and AutoLoad Plus software versions are current. Updates are available at
www.burk.com. The following are minimum software and firmware requirements
Software
Version
ARC Plus firmware
2.1.0, 3.0.0 recommended
AutoLoad Plus software*
2.0.0, 3.0.0 recommended
AutoPilot® 2010 software
2.5.0, 2.8.0 recommended
* Depending on your version of AutoLoad Plus, you may need to download the Plus-X 600
AutoLoad definition XML file from www.burk.com. Further instructions are available online.
The onboard web interface is compatible with Internet Explorer version 8 or newer, Firefox,
Chrome, and other modern web browsers.

Plus-X 600 Installation and Operation Manual Rev B
2
Unpacking
The Plus-X 600 ships with the following:
Plus-X 600 unit
Power cord
10’ shielded CAT5 cable
Six (6) 6-pin “Phoenix”-type plugs
Four (4) 9-pin “Phoenix”-type plugs
Front Panel Indicators
Front panel of the Plus-X 600
Indicator
State
Description
Power LED
Off
Power is off
Power LED
Green
Power is on
Power LED
Amber
No firmware loaded (contact Technical
Support)
Power LED
Flashing
Green
Resetting to factory default settings
Link LED
Green
Connected to ARC Plus
Link LED
Off
No connection to ARC Plus
Link LED
Flashing
Green, Red
Maintenance Mode
Link LED
Flashing
Red
No connection to ARC Plus, unit is in
maintenance mode
Hardware Configuration
The Plus-X 600 is configured via its onboard web interface. Open a web browser and navigate
to 192.168.0.100. The web page will prompt you for a username and password. Enter the
username admin and password password.
Note: The default IP address is 192.168.0.100 and the default password is “password”. If either
of these values have been changed and you do not know what they are, you need to perform a
master initialization. Press and hold the MASTER INIT button on the rear panel for three
seconds. This will reset the Plus-X 600 to its factory default settings.

Plus-X 600 Installation and Operation Manual Rev B
3
Settings
Click the Settings link on web page header to access the Plus-X 600 settings. Fill out the
following fields:
IP Address
Subnet Mask
Gateway
ARC Plus IP Address
You may optionally change the HTTP and Plus-X ports of the Plus-X 600. The default settings
are recommended.
Burk Technology recommends changing the Plus-X 600 password. The password is used to log
on to the onboard web interface. To change the password, check the Change Password box
and enter the new password in the Password and Confirm fields.
When you are finished, click Save.
Note: If you are unsure what network settings to use, contact your network administrator.
Plus-X 600 Settings

Plus-X 600 Installation and Operation Manual Rev B
4
Installation
Status Input Wiring
The Plus-X 600 status inputs are organized into two 2x6 “Phoenix”-type headers (four mating 6-
pin plugs are included). Pins for each channel and ground are labeled.
1
⏚
2
3
⏚
4
5
⏚
6
7
⏚
8
9
⏚
10
11
⏚
12
13
⏚
14
15
⏚
16
Metering Input Wiring
Metering inputs are available on a 2x6 “Phoenix”-type header (two mating 6-pin plugs are
included). Pins for each channel and ground are labeled.
1
⏚
2
3
⏚
4
5
⏚
6
7
⏚
8
Command Relays
Relay Pairing
The Plus-X 600 includes 12 relays.
Relays may be used individually, or in
raise/lower pairs (for up to 6 pairs). Use
the onboard web interface to configure
relay pairing. Log on to the web interface,
select Settings from the menu, then
Relay Pairs from the list on the left hand
side. Follow the onscreen instructions to
continue.
Paired Relay Example
Plus-X 600 relay #1 is paired with relay #7
and the ARC Plus has mapped the Plus-X
600’s channels starting at ARC Plus
channel #1.
In this scenario, ARC Plus Channel 1
Raise will use Plus-X 600 relay #1, and
ARC Plus Channel 1 Lower will use Plus-
X 600 relay #7. Note that ARC Plus
Channel 7 Raise and Lower are not used.
Relay Pairing

Plus-X 600 Installation and Operation Manual Rev B
5
Unpaired Relay Example
Plus-X 600 relay #1 is not paired and the ARC Plus has mapped the Plus-X 600’s channels
starting at ARC Plus channel #1.
In this scenario, ARC Plus Channel 1 Raise uses Plus-X 600 relay #1, and ARC Plus Channel 7
Raise uses Plus-X 600 relay #7.
Relay Wiring
The Plus-X 600 relays are organized into two 2x9 “Phoenix”-type headers (four mating 9-pin
plugs are included). Pins for common, normally open and normally closed are indicated for each
relay.
1
2
3
4
5
6
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
7
8
9
10
11
12
Software Configuration
Now that the Plus-X 600 is installed on the network, you are ready to add the unit to the ARC
Plus using AutoLoad Plus. Please download AutoLoad Plus from www.burk.com if you have not
done so already.
Note: For more information on configuring channels on the ARC Plus, refer to the ARC Plus
Installation and Operation Manual.
Adding the Plus-X 600 to the ARC Plus
Adding a Plus-X device in AutoLoad Plus

Plus-X 600 Installation and Operation Manual Rev B
6
In order for the ARC Plus to recognize the Plus-X 600, the Plus-X 600 must be added to the
site:
Open AutoLoad Plus and connect to the ARC Plus site to which you are adding the Plus-
X 600.
From the Edit menu, select Plus-X Devices to open the Plus-X device configuration
dialog.
Click Add to add the Plus-X 600 to the site.
AutoLoad Plus will prompt you to select the device type. Select Plus-X 600. You may
optionally change the description for the Plus-X device. The description appears in
AutoLoad Plus to identify each Plus-X device.
Enter the IP address and port number of the Plus-X 600. These should be the same
settings you used when you configured the Plus-X 600 via the web.
Check the Map default set of channels box if you wish to automatically add the Plus-X
600 channels to the ARC Plus (recommended). The ARC Plus must have 16
consecutive unused channels, including the starting channel.
Click OK.
Note: The above instructions are for AutoLoad version 2.3 or above. Earlier versions vary
slightly in appearance and labeling only.
Manually Mapping Plus-X 600 Channels
Setting the Channel Source in AutoLoad Plus

Plus-X 600 Installation and Operation Manual Rev B
7
If desired, you may manually map Plus-X 600 channels to ARC Plus channels in AutoLoad Plus
by selecting the Meter Channels, Status Channels or Commands tab, as appropriate:
Within any of these tabs, click the Source button to configure a channel to use a Plus-X
device channel as its source.
When the Source dialog appears, select Plus-X channel and choose the Plus-X device
from the list.
Select the Plus-X 600 channel you wish to use.
Click OK.
Once mapped, each Plus-X 600 channel will appear on the front panel of the ARC Plus, in
AutoPilot, on the ARC Plus web page, and will be accessible via the ESI.
Uploading New Firmware
You can load new firmware to the Plus-X 600 using its onboard web interface. Navigate to the
IP address of the Plus-X 600, log on, navigate to the Settings page and click the Upload
Firmware link. Click the Browse button to select the firmware file, then click Upload to load the
new firmware. The Plus-X 600 will reboot after the firmware upload is complete.
Uploading Firmware to the Plus-X 600
For the latest firmware updates, visit www.burk.com.

Plus-X 600 Installation and Operation Manual Rev B
8
Troubleshooting
If the network connection between the Plus-X 600 and ARC Plus is lost, the ARC Plus will log
an alarm after three minutes of network failure. The Plus-X 600 Link LED will also turn off.
Check your network settings on both the ARC Plus and Plus-X 600.
Note: Plus-X 600 events and errors are logged to the ARC Plus event list, which is accessible
by the ARC Plus front panel, ARC Plus Web Interface and from AutoPilot 2010.
Getting Help
For technical support, please email suppo[email protected]m or call our direct technical support line at
978-486-3711. We will be glad to assist you. The technical support office is open Monday –
Friday, 9AM to 5PM Eastern time.
Warranty
Burk Technology, Inc. warrants the Plus-X 600 to be free of defects in materials and
workmanship for a period of 24 months from the date of purchase. Equipment will be repaired or
replaced at the option of Burk Technology and returned freight prepaid to the customer.
Damage due to abuse or improper operation or installation of the equipment or caused by fire or
flood or harsh environment is not to be covered by this warranty. Damage in shipping is not the
responsibility of Burk Technology. A return authorization must be obtained before returning any
equipment. Materials returned under this warranty must be shipped freight prepaid and insured
in the original shipping carton or suitable substitute to Burk Technology, Inc., 7 Beaver Brook
Road, Littleton, MA 01460. Repairs not covered under this warranty will be made at prevailing
shop rates established by Burk Technology.
THE WARRANTY SET FORTH ABOVE IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BURK TECHNOLOGY,
INC. SHALL NOT BE LIABLE TO ANY PARTY FOR ANY INCIDENTAL, SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF THIS EQUIPMENT.

Plus-X 600 Installation and Operation Manual Rev B
9
Appendix A: Specifications
Dimensions:
1.75” (4.45cm) H
19” (48.26cm) W
12” (30.48cm) D
Operating Temperature:
0oto 40oC
Power Requirements:
100 to 240VAC, 47-63Hz, 1A; power entry module with standard, grounded power cord
supplied; 1A fuse protection
Connectivity:
Ethernet connection to ARC Plus
Channel Capacity:
16 status, 8 metering and 6 command channels
Metering Input Range:
-10VDC to +10VDC
Metering Input Accuracy:
>99.75% accuracy, full scale
Status Input Range:
>0 to 28VDC or switch closure
Output Types:
C, NO, NC relay outputs; momentary or latching; 5A, 240VAC