Bushnell Aggressor 119774C User manual

Model#s: 119774C / 119775C / 119776C / 119777C
INSTRUCTION MANUAL
01-15

3

4
IMPORTANT NOTE
Congratulations on your purchase of one of the best trail cameras on
the market! Bushnell is very proud of this little unit and we are sure you
will be pleased with it as well. We appreciate your business and want to
earn your trust. Please refer to the notes below and the instructions in
this manual to ensure that you are completely satisfied with this product.
If your Bushnell Trophy Cam HD Aggressor does not seem to be
functioning properly or if you are having photo/video quality issues,
please check the Troubleshooting/FAQ section on pages 31-35.
Problems are often due to something simple that was overlooked,
or require only changing one setting to solve.
If your problem continues after trying the solutions in the
Troubleshooting/FAQ section, please call Bushnell Customer
Service at [phone]. In Canada, call [phone].
Bushnell recommends using a full set of eight Energizer®Lithium
AA batteries in these Trophy Cam HD Aggressor models to obtain
maximum battery life
Do not mix old and new batteries
Do not mix battery types-use ALL lithium or ALL alkaline
Bushnell recommends using SanDisk®class 6 or faster SDHC
Cards (up to 32GB capacity) in your Trophy Cam HD Aggressor

5
INTRODUCTION
About the Trophy Cam HD Aggressor
The Bushnell Trophy Cam HD Aggressor is a digital scouting camera. It can be
triggered by any movement of game in a location, detected by a highly sensitive
Passive Infra-Red (PIR) motion sensor, and then take high quality pictures (up to
14MP still photos), or video clips.
The Trophy Cam HD Aggressor consumes very little power (less than 0.25 mA) in
a stand-by (surveillance) state. This means it can deliver up to six months stand-by
operation time when the device is powered by the full capacity of AA alkaline batteries,
and up to twelve months utilizing lithium AA batteries. Once motion in the monitored
area is detected, the digital camera unit will be triggered at once (typically within
one second) and then automatically take photos or videos according to previously
programmed settings. The Trophy Cam HD Aggressor is equipped with built-in
infrared LEDs that function as a flash, so that it delivers clear photos or videos (in
black & white) even in the dark, and it can take color photos or videos under sufficient
daylight. The Trophy Cam HD Aggressor HD is designed for outdoor use and is
resistant against water and snow.
Your trail camera is one of the latest generation of Bushnell Trophy Cam HD
Aggressor HDs, and includes many new or improved features, including:
• Auto PIR Sensitivity-the camera monitors ambient temperature conditions and
automatically adjusts the sensor/trigger signal to be more sensitive to slight
variations in temperature on hot days, less sensitive on cold days.
• Hyper NightVision-The IR LED Flash array now has increased range, brighter
output and better coverage for improved nighttime images. Models 119776C &
119777C feature "No-Glow" Black LEDs, invisible to game and other hunters.
• Field Scan 2x with Live Trigger-This “time lapse” feature includes the option
for a second block of recording with its own start/stop times. Trigger signals
generated by nearby wildlife activity will still generate additional photos/videos
as they normally would, independently of the Field Scan operation.
• GPS Geotag Capability-allows the user to input the longitude and latitude of
the camera’s position, which will be embedded in each photo file. This enables
Google Earth, Picassa and other geotag enabled software to automatically
show a map pinpointing each camera’s location when a group of photos are
reviewed on a computer. Especially useful for those who setup multiple Trophy

6
Cam HD Aggressors to monitor large or widely separated areas.
• Multi Flash Mode (LED Control)- prevents overexposed flash photos in close
range applications
• Hybrid Capture Mode-allows both still photos and videos to be captured at each
trigger, up to highest resolution settings for each.
• NV Shutter-user can select shutter speed for images captured at night allowing
control over brightness vs. ability to stop motion
• Camera Operating Mode can be limited to Day only, Night only, or 24 HRs
And many more features such as 1080p HD Video with Audio, 0.2 second trigger
speed and 1 second recover time (still photos), widescreen or fullscreen format
still photos, imprintable camera name (user set) along with current data including
temperature and moon phase.
Applications
The Trophy Cam HD Aggressor can be used as a trail camera for hunting or
scouting game. It is also suitable for surveillance usage.
PARTS AND CONTROLS
The Trophy Cam HD Aggressor provides the following connections for external
devices: USB port, SD card slot and external DC power in (pg 7, Fig. 1).
A 3-way power switch is used to select the main operating modes: OFF, SETUP,
and ON (pg 7, Fig. 2).
A control key interface with six keys is primarily used in SETUP mode to select
operational functions and parameters. As shown on the next page, these keys are: UP,
DOWN, LEFT, RIGHT, OK and MENU. Three of the keys can also perform a second
function (shortcut operations in SETUP mode) in addition to their main function: The
DOWN key can be used to set the camera to Photo mode (still camera icon), and
the UP key can set the camera to Video mode (movie camera icon). The RIGHT key
also serves as the manual shutter (“SHOT”) button of the camera. These secondary
functions are indicated by icons or text above the key as shown on the next page.

7
INSIDE VIEW
Fig. 2: Button and
Switch Guide
ON
SETUP
OFF
LCD Screen
Power/Mode
Switch
UP/Video
DOWN/Photo
LEFT
MENU
OK
RIGHT/Shot
Cable to Battery
Compartment
Tripod Socket
DC in
Cover Plug
Video Mic
Fig. 1: Connections
FRONT VIEW
LED IR
Flash Motion/ Low
Battery Indicator
Lens
Lock
Hole
PIR
Sensor Latch
Light
Sensor
ARD
USB Port
SD Card Slot
DC In
Video Mic

8
INSTALLING THE BATTERIES AND SD CARD
Before you begin learning how to use your Trophy Cam HD Aggressor, you will first
need to install a set of batteries and insert an SD card. Although that may only take
you a minute, there are some important notes about both batteries and SD cards you
should be aware of, so please take the time to read the following directions and
cautions:
Loading Batteries
After opening the two latches on the right side of the Trophy Cam
HD Aggressor, you will see that the Trophy Cam HD Aggressor
has eight battery slots. For maximum battery life, you should install
a full set of batteries. The Trophy Cam HD Aggressor may also
be operated by just four batteries installed in the first slots only
(starting on the top or left-see photos). Battery life will be shorter
with 4 batteries, but the camera will operate normally. Whether you
use 4 or a full set, be sure to insert each battery with correct polarity
(negative or “flat” end against the long spring of each battery slot).
Bushnell recommends using a full set of new lithium AA (Energizer®
brand) or alkaline AA batteries. NiMh Rechargeable batteries are not recommended,
as the lower voltage they produce can cause operational issues.
You can also connect an optional Solar Panel accessory (model# 119756C -please
visit www.bushnell.com for more information) to the “DC In” jack at the bottom of the
Trophy Cam HD Aggressor (other external power supplies should not be used, as
the camera and/or display may not function correctly). If the solar panel is connected
and AA batteries are installed, the Trophy Cam HD Aggressor will be powered by
the solar panel's rechargeable lith-ion battery, as long as it provides adequate voltage
(if not, the camera will switch to battery power). The solar panel's battery will power
the camera at night.
When the batteries become weak (or a device with insufficient power is connected
to DC In), the low-battery indicator LED will glow blue, indicating the batteries should
be changed (pg 7, Front View).

9
Inserting the SD Card
The Trophy Cam HD Aggressor has 32MB of internal memory, which can hold only
about 18 photos (@ 8MP resolution). This is handy for testing and getting familiar
with the camera, but you will no doubt want to leave the camera unattended for longer
than a day, so using an SD card is recommended for all models. Insert the SD card
(with the camera’s power switch in the OFF position) before beginning to operate
the camera. Don’t insert or remove the SD card when the power switch is in the ON
position.
The Trophy Cam HD Aggressor uses a standard SD (Secure Digital) memory
card to save photos (in .jpg format) and/or videos (in .avi format). SD and SDHC
(High Capacity) cards up to a maximum 32GB capacity are supported. Using high
speed SD cards (SanDisk®SDHC rated class 6 or higher) is recommended if you will
use the 1280x720 or 1920x1080 HD video settings. Before inserting the SD card
into the card slot after opening the camera’s front cover, please make sure that the
write-protect switch on the side of the card is “off” (NOT in the “Lock” position). The
following describes how to insert and remove the SD card:
• Insert the SD card into the card slot with its label side upwards (see below). A
“click” sound indicates that the card is installed successfully. If the wrong side
of the card is facing up, you will not be able to insert it without force-there is
only one correct way to insert cards. If the SD card is not installed correctly,
the device will not display an SD card icon on the LCD in SETUP mode (the
SD card icon displayed after switching to SETUP mode will have a “lock” symbol
inside it in it if the card is locked). Formatting the SD card by using the Trophy
Cam HD Aggressor’s “Format” parameter before using it for the first time is
recommended, especially when a card has been used in other devices (see pg.
23, “Format” for details).
• To take out the SD card, just gently push
in the card (do not try to pull it out without
pushing in first). The card is released from the
slot and ready to be removed when you hear
the click. WARNING: Be sure the camera’s power is switched OFF
before inserting or removing SD cards or batteries.

10
USING THE Trophy Cam HD Aggressor
Once you’ve prepared your Trophy Cam HD Aggressor by properly installing
batteries and an SD card, you could simply take it outside, strap it to a tree, switch it
on and leave-and you might get some great photos that are exactly what you wanted.
However, we highly recommend that you first spend some additional time indoors with
this manual and your camera until you know a bit more about what the 3-way switch
and those control keys do. If nothing else, you’ll probably want to at least set the date
and time so the camera will imprint them (or not-it’s your option) on your photos as
they are taken, learn how to set the camera to shoot video clips instead of still photos
if you like, and read some tips about mounting it on a tree.
THE OFF, ON, AND SETUP MODES
The Trophy Cam HD Aggressor has three basic operational modes:
• OFF mode: Power switch in the OFF position.
• ON mode: Power switch in the ON position (LCD screen is off.)
• SETUP mode: Power switch at SETUP position (LCD screen is on).
OFF MODE
The OFF mode is the “safe” mode when any actions must be taken, e.g., replacing
the SD card or batteries, or transporting the device. You will also use OFF mode if
you connect the camera to a computer’s USB port later to download your photos/
videos. And of course, when you are storing or not using the camera, you will switch it
to OFF. Please note that even in the OFF mode the Trophy Cam HD Aggressor still
consumes power at a very low level. Therefore, it’s a good idea to take the batteries
out of the battery compartment if the camera will not be used for a long time.
ON MODE
Anytime after the batteries and SD card have been inserted, you can switch on the
camera. When the power switch is moved to the top position, the camera will enter
into the ON (Live) mode. The motion indicator LED (pg. 7, “Front View”) will blink
red for about 10 seconds. This interval allows time for you to close the Trophy Cam
HD Aggressor’s front cover, lock it, and leave the monitored area. Once in the ON
mode, no manual controls are needed or possible (the control keys have no effect).
The Trophy Cam HD Aggressor will take photos or videos automatically (according

11
to its current parameter settings) when it is triggered by the PIR sensor’s detection of
activity in the area it covers.
You can either move the power switch directly from OFF to ON mode, or stop at the
SETUP position first to change one or more settings, then move the switch to ON
after you have finished doing so.
SETUP MODE
In the SETUP mode you can check and change the settings of the Trophy Cam
HD Aggressor with the help of its built-in LCD. These settings, found in the SETUP
Menu, let you change the photo or video resolution, interval between photos, switch
the time imprint on, etc. Moving the power switch to the SETUP position will turn on
the LCD display, and you will see an information screen that shows how many images
have been taken, the battery level, camera or video mode, etc (Fig. 3, next page).
NOTE: Always move the power switch from OFF to SETUP mode. It is possible
that the camera could lockup if it is switched from ON to SETUP mode. If this
occurs, simply move the switch to OFF and then push it up to SETUP again.
SETUP Mode Shortcut Keys/Functions
As mentioned earlier in “Parts & Controls”, four of the keys below the LCD
have secondary, “shortcut” functions when the camera is switched to SETUP mode
(but the MENU key has not been pressed):
• Press the UP key to quickly set the camera to shoot video clips.
• Press the DOWN key to quickly set the camera to take still photos.
• Press the RIGHT key to manually trigger the shutter. This is useful for testing the
camera-make sure you are in SETUP mode, press the RIGHT key, and a few
seconds later a photo or video (depending on how the camera was set) will be
saved to the SD card (or internal memory if no card is inserted). The “number of
images taken” counter on the bottom left of the LCD will increase by one. If the
display indicates “SD PROTECTED” when you press the SHOT key, switch the
camera OFF, remove the SD card and slide its protect switch off.

12
Fig. 3: SETUP Information Screen
5
5
Still Photo Mode
Time Stamp
Field Scan On
# of Photos Taken Remaining Photo Capacity
Date:Month-Day-Year
Battery Level
Image Size (Resolution) SD Card Status
Time
Hour:Minute:Second
Camera (Still Photo) Mode
Video Mode
Video Sound On Video Resolution
Available Video Recording Time
Video Mode

13
USING THE SETUP MENU TO CHANGE SETTINGS
The main purpose of the SETUP mode is to allow you to change the settings of
the camera’s parameters (19 different ones are available!) so your Trophy Cam HD
Aggressor operates exactly the way you want it to. You will do this by entering the
SETUP Menu and pressing the keys below the LCD display, which will show you
each parameter and its setting.
Changing Parameter Settings in SETUP Mode
A wide range of options or “parameters” are provided to allow you to set the Trophy
Cam HD Aggressor to your operational preferences. To change the setting of
any parameter you must first switch to the SETUP mode. Once in SETUP mode,
pressing the MENU button will allow you to select any parameter and change its
setting. The name of the parameter and its current setting will be shown on the LCD.
Pressing the RIGHT or LEFT key scrolls to the next or previous parameter (RIGHT
key to move on to the next parameter and LEFT key to go back to the previous
parameter), and pressing the UP or DOWN key lets you select a different setting
for the currently displayed parameter. Once you have selected your preferred new
setting for a parameter, press the OK button to save the new setting (actually change
it). When you are finished changing the settings of one or more parameters, press
MENU again to exit the SETUP menu. MENU can also be pressed anytime you
want to cancel changing a parameter’s setting after a new setting has been selected
(but OK has not been pressed yet). After setting the parameters to your preferences,
be sure to move the switch to ON to begin actually taking photos or videos. No
images will be captured if the switch is left in the SETUP position (unless you press the
RIGHT/Shot key after exiting the menu)-in fact, the camera will power off automatically
after a few minutes with no key pressed.
Parameter Settings Display
The settings for each parameter are shown on the display screen of your Trophy
Cam HD Aggressor. Only one setting is displayed at a time, starting with the current
setting for the parameter when it is first selected (pg. 14, Fig. 4a). To change the
setting, use the UP/DOWN keys to display the new setting you want (Fig. 4b), then
press OK to “Execute” (make the actual change to this setting). If you want to confirm
this setting is now the current one, just press the RIGHT key to scroll to the next
parameter, then press LEFT to go back again to the previous one. You should see the
parameter setting you just made.

14
Fig. 4: Selecting Parameter Settings
(4a)
(4b)
Press MENU
Press DOWN
Press OK

15
EXAMPLES-Changing the Settings of Some Common Parameters
Following this page, you will find tables listing all of the parameters found in the
SETUP Menu, along with their possible settings (or range of settings), and a detailed
description of what the parameter controls and what the settings do. If you read the
previous section detailing how to select parameters and change their settings, you
should be able to dive right in, find the parameter(s) you want, and setup the camera
to suit your preferences. But maybe you’d rather walk through an example or two first:
To change any parameter’s setting, always start with the power switch in the SETUP
position. After the LCD comes on, press the MENU key.
The first parameter you will see when you first enter the SETUP Menu is “Mode”.
To change it from its default setting of “Camera” (still photos) to “Video” (shoot
video clips), press the DOWN key to select the “Video” setting. Press the OK key to
“Execute” (Set) the new setting you’ve selected for this parameter.
Now press the RIGHT key to move to another parameter in the Menu. Pressing it
three times will take you to “Capture Number”. Try using the UP and DOWN keys
to scroll through the range of settings, then press OK to lock in your setting for the
number of photos the camera takes each time it's triggered.
Pressing the RIGHT key until you reach the last menu item, you'll see the “Default
Set” parameter. Highlight or select “Execute” (using UP or DOWN) and press OK to
restore all parameters (including the Mode and Video Length parameters you changed
a minute ago) back to their original factory default settings. The default settings for
each parameter are indicated in bold type in the SETUP Menu tables on the next
several pages.
Be sure to set the current date and time, using the “Set Clock” parameter, if you
choose to change the “Time Stamp” parameter setting to “On” since that will tell the
camera to imprint the date and time on each of the images it captures.

16
Field Scan 2x with Live Trigger Feature
Field Scan is a revolutionary new feature for the Bushnell Trophy Cam HD
Aggressor, which allows you to monitor your food plots or field edges with time lapse
images or video. When set to “On”, the Trophy Cam HD Aggressor will take a photo
(or record a video clip) automatically at your choice of intervals (for example, once
every five minutes) during one or two blocks of time you set up for each day, without
requiring a trigger from an active animal. This has the advantage of giving you
the ability to monitor the edge of a field that might be 50 or 150 yards away from the
camera out of the PIR sensor’s range. The result is an effective range much greater
than it would normally be, with the camera dependant on triggers generated by nearby
animals. This is a great tool for hunters to scout an entire field with only one camera.
If an animal does enter the area covered by the PIR sensor and generate a trigger
event during a time in between the Field Scan intervals you set, the camera will capture
an image or video just as it normally would, based on your other menu settings. Here’s
how to setup and use Field Scan (be sure you’ve set the current time in “Set Clock”
first, so your Field Scan recording will stop and start at the correct times of day):
1. Move the main switch to SETUP, then press MENU.
2. Keep pressing the RIGHT key, stepping through the Setup Menu until you reach
Field Scan.
3. Press the UP key to select On, and press OK (Step 1, pg.18). You will see "A",
representing the first block of time you can define (a second block of time later
in the day, "B" can also be setup if you wish). Press OK (Step 2). This takes
you to the screen to set Start and Stop times, which determines the clock times
when the first block of Field Scan recording will begin and end for each day.
You can set these times to the exact hour and minute you want, for a recording
“window” that lasts anywhere from just a minute to a full 24 hours.
4. Set the [Start] and [Stop] times, beginning with the Start hour, using the UP/
DOWN keys to change the setting (Step 3). The hour setting is based on a 24-
hour clock, with “00” hours = midnight, “12” hours = noon, “23” hrs = 11PM,
etc. To move to the next setting, press the RIGHT key, change the minute for
the Start time with UP/DOWN, then on to the hour and minute settings for the
Stop time.
5. After you finish setting the Stop minutes, press OK to confirm your settings for
the first block of Field Scan recording. If desired, you can create a second block

17
of time by pressing the DOWN key to select "B" (Step 4), then press OK and
follow the same process to set Start and Stop times for Field Scan block "B"
(Step 5). As an example of how you might use these two available time blocks,
you could setup Field Scan time block "A" for the dawn hours from 6 AM to 8
AM, and block "B" to capture images between 5:30 and 7 PM. No Field Scan
recording would occur from 8AM to 5:30PM, or from 7PM to 6AM.
6. After setting Start/Stop times to define Field Scan block "A" and/or "B", press
OK, then press the UP or DOWN key to select "Interval" and press OK (Step
6). The Field Scan "Interval" setting lets you control how often a photo or video
clip is recorded during the block(s) of time you defined with the Start and Stop
settings. Your options are 60 minutes, 30 minutes, 15 minutes, 5 minutes (this
is the default), or 1 minute (still photo mode only). Use the UP/DOWN keys to
select your preference, then press OK to save it (Step 7). Note that for videos,
"Interval" is independent of the Length of each video recording-it’s how often
videos are recorded, not how long each one lasts.
7. Here’s an example of how the camera would operate, based on the following
Field Scan settings:
Field Scan: On
Field Scan A:
[Start]: 6:00
[Stop]: 8:00
Field Scan B:
[Start]: 17:30
[Stop]: 19:00
Interval: 15M
These settings would cause the camera to capture a photo (or video, if the
camera is set to that mode) once every 15 minutes, beginning at 6 AM, until the
Field Scan "A" recording block stops at 8:00 AM. Later that day, the camera
would again take a photo or video every 15 minutes between 5:30 PM and
7:00 PM (during Field Scan time block "B"). The next day, the camera would
again record an image or video once every 15 minutes between 6:00 and 8:00
AM, and between 5:30 and 7:00 PM. No Field Scan recording would occur
from 8AM to 5:30PM, or from 7PM to 6AM. Remember, Field Scan recording
is independent of normal triggers due to animal activity–even if no animals enter
the IR sensor coverage zone, an image or video will still be captured every 15
Note: avoid any "overlap" of Field Scan A & B
recording blocks when setting their start and stop
times, to assure correct operation. Also-if the "Camera
Mode" menu parameter is set to "Day" or "Night"
operation only, that will take priority over your Field
Scan settings. Set the Camera Model to "24 HR" if
you are setting both day and night start and/or stop
times in Field Scan.

18
minutes during the block(s) of time. If an animal triggers the camera “in between”
the 15 minute intervals, it will be recorded.
Note: Field Scan settings of frequent intervals and/or long periods between
start and stop time can reduce battery life.
(Step 1)-set Field
Scan Mode to “On”
(Step 2)-select Field
Scan "A" (press OK)
(Step 3)-set Field
Scan "A" Stop & Start
(Step 4) (opt)-select Field
Scan "B" (press OK)
(Step 5) (opt)-set Field
Scan "B" Stop & Start
Steps 4 & 5 are
optional (only
required if you want
to set up a second
block of Field Scan
recording with
different stop and
start times)
(Step 6)-select Field
Scan "Interval"
(Step 7)-set Field
Scan Interval
Note: the Interval
Setting sets the
timing between each
image for both Field
Scan "A" and "B"
recording blocks.

19
Parameter Settings
(Bold=default)
Description
Mode Camera,Video,
Hybrid
Selects whether still photos or video clips
are captured when the camera is triggered.
Hybrid mode combines both Camera and
Video, so a still photo and a video clip are
both captured for each trigger.
Image Size
(only aects
still photos
in Camera or
Hybrid modes)
3M Pixel,
8M Pixel,
14M Pixel
Selects resolution for still photos from 3 to
14 megapixels. Higher resolution produces
better quality photos, but creates larger files
that take up more of the SD card capacity
(fills up faster). 8M is a good compromise
between quality and file size.
Image Format
(only aects still
photos-
format for video
is tied to Video
Size)
Full Screen,
Wide Screen
Selects 4:3 (Fullscreen, like old TV sets) or
16:9 (Widescreen, like new flat TVs) “aspect
ratio” for still photos. If you like to view your
photos on a TV set or computer monitor, you
can set the format to match it.
Capture
Number
(only aects
still photos
in Camera or
Hybrid modes)
1 Photo,
2 Photo,
3 Photo
Selects how many photos are taken in
sequence per trigger in Camera mode. This
setting affects photos taken in Field Scan
mode as well (to snap two photos every 10
minutes, for example). Note: only one photo
will be captured if "Interval" is set to 1 second,
regardless of the Capture Number setting.
Please also refer to the Interval parameter.
The SETUP Menu – Parameters and Settings List
w/Descriptions

20
Parameter Settings
(Bold=default)
Description
LED Control
(Multi-Flash
feature)
Low, Medium,
High
Controls how many LED lamps fire when
images are taken in low light. “High”=
all LEDs fire (36 or 48, depending on
the model), which is the default setting.
Set to Medium or Low if you are getting
overexposed flash photos or will place the
camera at very close range to the subject you
want to photograph. In general, select High
if most of your intended subjects will be over
30 ft. from the camera, Medium for the 15
to 30 ft. range, and Low for subjects under
15 ft. away. Note: in video mode, set to LED
Control to "Low" if videos are overexposed
at the Medium setting.
Camera Name (Input)
See "Using the
Setup Menu Input
Screens"
Allows the user to set a custom name for the
camera. Useful for ID purposes when multiple
cameras are setup, since each camera will
imprint its name on all photos (but not videos)
it captures.
Video Size
(only aects
video clips in
Video or Hybrid
modes)
1920x1080,
1280x720,
640x360
Selects video resolution (in pixels per frame).
Higher resolution produces better quality
videos, but creates larger files that take up
more of the SD card capacity (fills up faster).
640x360 is VGA video in "widescreen" 16:9
format. The highest setting provides HD
video. Using high speed SD cards (SanDisk®
SDHC class 6 or higher) is recommended
if you will use the 1280x720 or 1920x1080
video settings.
Video Length
(only aects
video clips in
Video or Hybrid
modes)
10S (second)
default, with 60S
to 5S possible
range
Sets length per captured video clip.
Settings begin with 10 second default when
parameter is first selected. After stepping
down to 5S, video length settings start over
at 60S.