Buyers LT25 User manual

www.buyersproducts.com
Phone [phone]
Fax [phone]
1
LT25 Water Cooler Rack
for Utility Landscape Trailers
Holds most 5-gallon water coolers.
—continued
Before you begin installing:
1. Read and understand these instructions
completely.
2. Verify that you have received all the parts
listed in the bill of materials.
The water cooler rack must be mounted with
back and bottom support or back support. This
rack is not to be mounted with bottom support
only.
Utility Trailer Installation Instructions
Tools Required:
• (2) 9/16" Wrenches and/or Sockets
• Electric Drill
• 13/32" Drill Bit
1. Find a location on your trailer where the water
cooler rack can be mounted with back and bottom
support or back support. Make sure the rack does
not extend past the widest part of the trailer.
Holding the rack level mark three hole locations.
2. Drill 13/32" holes in the positions marked.
Installation Instructions
CAUTION
Always wear safety glasses when using power tools.
WARNING
Check under the trailer and/or fender for locations of
brake lines and electrical wiring etc., before drilling any
holes. Any damage to trailer during installation is install-
er’s sole responsibility.
3. Thread straps through the slots in the rack
and then the buckle as shown in the illustrations.
4. Bolt the rack to the trailer with three 3/8-16
x 1-1/4 screws, six 3/8" flat washers, and three
3/8-16 nylock nuts and tighten.
5. Assemble the water cooler into the rack
and tighten straps. Cut off the end of each strap
approximately 6-8" from buckle and carefully burn
the ends with a cigarette lighter to prevent fraying.
Bill of Materials
1 3000050 1 Water Cooler Rack, Weldment
2 3004710 2 Strap, 60" Lashing w/Cam Buckle
3 - 6 Washer, Flat 3/8 USS Zn
4 - 3 Screw, HHC 3/8-16 x 1-1/4 Gr 5 Zn
5 - 3 Nut, Nylock 3/8-16 x 7/16 Zn
ITEM PART NO. QTY. DESCRIPTION

www.buyersproducts.com
Phone [phone]
Fax [phone]
2
3000687 Rev. C
Enclosed Trailer Installation Instructions
Tools & Materials Required:
• 9/16" Wrench and/or Socket
• Electric Drill
• 1/4" Drill Bit
• 3/4" Plywood Shim Strips
• Shim Screws
1. In order to mount this rack to an enclosed
trailer, you must first add 3/4" plywood shim strips
to the walls. These shim strips must be attached to
at least two wall support studs with suitable fasten-
ers. If you don’t know what kind or length of fastener
to use contact your trailer dealer or manufacturer for
their recommendation. The shim strips should not
completely cover the four slots in the water cooler
rack. One inch of each slot needs to be unobstructed
for strap attachment.
2. Place the rack against the shims, hold level, and
mark the position of the three 3/8" holes in rack.
3. Drill three 1/4" holes in the center of your marks
1" deep. Be extremely careful not to drill through
the outside trailer wall.
4. Fasten the rack to the trailer wall with three 3/8"
lag screws and three 3/8" flat washers supplied.
5. Thread straps through the slots in the rack and
then the buckle as shown in the illustrations.
6. Assemble the water cooler into the rack and tight-
en straps. Cut off the end of each strap approximate-
ly 6-8” from buckle and carefully burn the ends with a
cigarette lighter to prevent fraying.
Bill of Materials
1 3000050 1 Water Cooler Rack, Weldment
2 3004710 2 Strap, 60" Lashing w/Cam Buckle
3 - 3 Washer, Flat 3/8 USS Zn
4 - 3 Screw, Hex Head Lag, 3/8 x 1-1/4 Zn
ITEM PART NO. QTY. DESCRIPTION
WARRANTY
Buyers Products Co. warrants all truck/trailer hardware manufac-
tured or distributed by it, to be free from defects in material and
workmanship for a period of one year from date of shipment.
Parts must be properly installed and used under normal conditions.
Any product which has been altered, including modification, mis-
use, accident or lack of maintenance will not be considered under
warranty. Normal wear is excluded. The sole responsibility of Buyers
Products Co. under this warranty is limited to repairing or replacing any
part or parts which are returned, prepaid, and are found to be defective
by Buyers Products Co. Authorization from Buyers Products Co. must
be obtained before returning any part. No charges for transportation
or labor performed on Buyers’ products will be allowed under this
warranty.