CableWholesale PLB-CE348 User manual

INSTALLATION INSTRUCTIONS
Max Load Capacity: 50kg(110lbs)
50kg
(110lbs)
MAX
Model: PLB-CE348
PLB Ceiling Mount
7
Tilting angle:
-15° ~ 0°
fig. 8.1
3Pitching Angle Adjustment
Use the iron knob to adjust your TV to the desired angle, and then tighten the iron knob. the pitching angle
can be adjusted between -15° ~ 0° as shown in fig.8.1.
8
Maintenance
Once you have mounted the bracket and the flat screen, check that they are sufficiently secure and safe to
use. You should check whether screws are fixed well each two months. If you have any doubts regarding the
installation, please consult our retailer or service department for details.
0°
-15°
fig.7.1

NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions and
warnings contained in this installation sheet. If you have any questions regarding any
of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as specified in
this manual. Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone of good mechanical ability, with basic
building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
• Never exceed the maximum load capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the items,
greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
21
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone the local distributor for a replacement.
Tools required
Phillips head screw driver(200mm length exclude the handle)
Wrench and socket
Electric drill and 12mm masonry bit for concrete wall installation
Marking pen
Hammer
·
·
·
·
·
Package M
Package
D8 ø8.5 ø16 (x5)
P-F
x washer M8 nut (x4)
P-E
M8 (x4)
P-K
x70 iron expansion bolt
M4x20
M-B
(x4)M4x10
M-A
(x4) M5x10 (x4)
M-C
M5x20 (x4)
M-D
M6x10 (x4)
M-E
M6x20 (x4)
M-F
M8x15 (x4)
M-G
M8x30
M-H
(x4) ø15xø8x15
M-K
(x4)
ø (x4)
M-J
14xø6x10
washer
M-I
(x4)
M8x60
P-A
(x1) M8x60
P-B
(x1) M8x14
P-D
(x2)
M8x55
P-C
(x1)
washer
P-G
(x4) ø10.5 ø20 (x1)
P-H
x washer
ø8.5 ø17.5 (x3)
P-I
x washer M8 iron knob
P-J
(x1)
outer column (x1)
A
inner column (x1)
B
hook plate (x1)
F
universal plate (x1)
G
adapter bracket (x2)
H
ceiling plate (x1)
C
small plastic
bushing (x1)
D
big plastic
bushing (x1)
E

43
Installing the Column of Ceiling Mount
• Run power cable through channel as shown in fig.3.1.
• Install the inner column into the outer column at desired height and secure it using screw (P-C), washer (P-F)
and nut (P-E) as shown in fig.3.1.
3
fig.3.1
P-C P-F
P-E
fig.4.1
Installing the Universal Plate
Attach the universal plate to hook plate using screws (P-D) , washer (P-F) and nut (P-E),tighten nuts using a
proper socket as shown in fig.4.1.
4
Attach the assembled universal plate to the ceiling mount using the appropriate combination of screws,
washers, nut and iron knob. Tighten all screws as shown in fig.4.2.
fig.4.2
P-A
P-H
P-B
P-I
P-G
P-G
P-J
P-F
P-I
P-F
P-I
P-E
Marking the Mounting Holes Locations
Determine the exact mounting location prior to installation, and then use the ceiling plate as a template to
mark four holes locations on the ceiling as shown in fig.1.1.
1
Installing the Ceiling Plate and the Plastic Bushings
Slide the big plastic bushing along the outer column till the big plastic bushing is reached the top position.
Install the ceiling plate in the same way. And then insert the small plastic bushing into the end of outer column
as shown in fig.2.1.
2
fig.2.1
fig.1.1
D
C
E
A
C
B
P-E
P-F
P-D

65
fig.5.1
M-A
M-C
M-E
M-G
M-I
fig. 6.1
For Flat Back Screen
• Begin with the shortest length screw, hand thread through washer and adapter bracket into screen as shown below.
• Screw must make at least three full turns into mounting hole and fit snug into place. Do not over tighten.
• If screw cannot make three full turns into screen, select a longer length screw. Repeat for remaining mounting holes,
level brackets and tighten screws.
NOTE: Spacer may not be used, depending upon the type of screen.
6
1
• Begin with longer length screw, hand thread through washer, adapter bracket and spacer into screen as
shown below.
• Screw must make at least three full turns into mounting hole and fit snug into place. Do not over tighten.
• If screw cannot make three full turns into screen, select a longer length screw. Repeat for remaining mounting
holes, level brackets and tighten screws.
For Bump-out or Recessed Back Screen
M-B
M-D
M-F
M-I
fig. 6.3
M-J
6
2
fig. 6.2
M-H
M-I
M-K
7Warning: A minimum of two qualified people are required for this operation.
• Loosen the safety screw on the adapter brackets, as shown in fig. 7.1.
• Hook the TV onto the universal plate and tighten the safety screws with a proper screw driver as shown in fig. 7.1.
Important: Make sure the TV is correctly hooked and the safety locking screws are locked safely before
releasing the TV.
Hang TV onto the Universal plate
NOTE: For flat back screens proceed to step 4-1. For bump-out or recessed back screen skip to step 4-2.
• To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the
screen.
• Place screen face side down. Place adapter brackets on the back of screen, align to holes, and center
on back of screen.
• Attach the adapter brackets to the back of the screen using the appropriate combination of screws,
washers, and spacers, as shown in fig.4.1, fig.4.2 and fig.4.3.
6Installing Adapter Brackets
P-K
WARNING
• When installing PLB ceiling mounts on cinder block, verify that you have a
minimum of 1-3/8” of actual concrete thickness in the hole to be used for the
concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of
the block, generally 1” minimum from the side of the block. It is suggested electric
drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breaking out the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
into each of these holes. Attach the ceiling plate to the ceiling using other parts of iron expansion bolt as
shown in fig.5.1.
Pre-drill these marked holes with a 12mm masonry bit to at least 45mm in depth. Insert an iron expansion bolt
Solid Brick and Concrete Block Mounting:
5