Calflame BBQ08852P User manual

Copyright 2009-2010 LMS, Inc. All rights re-
served. Duplication without written consent
is strictly prohibited.
Cal Flame®is a registered trademark.
Due to continuous improvement programs,
all models, operation, and/or specications
are subject to change without prior notice.
LTR50001082, Rev. B
5/26/11
250-407
Installation / Assembly
Cabinet Cut-out Dimensions.........................4
Gas Requirements and Connection ...................5
Leak Testing Procedure.............................6
LP Gas ..........................................7
Natural Gas ......................................9
Installing Side Burner with a Grill ...................10
Using Your Side Burner
Lighting the Side Burner...........................12
Basic Side Burner Operation........................14
Cleaning and Maintenance
Stainless Steel Care and Cleaning ...................15
Covering Your Side Burner .........................18
Appendix
Troubleshooting .................................19
Converting Side Burner from LP to NG................21
Replacement Covers ..............................22
Limited Warranty.................................23
Save these instructions!
California Proposition 65 Warning:
Chemicals known to the State of
California to cause cancer, birth
defects or other reproductive
harm are found in and/or creat-
ed by the combustion of natural
gas, propane, butane and other
fuels. Always operate this unit as
described in the owner’s manual
and in well ventilated areas.

Safety Instructions
1
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Safety Instructions
WARNING: Improper installation, adjustment, altera-
tion, service or maintenance can cause injury or property
damage. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this
equipment.
Placement and Location
C• al Flame side burners are designed for outdoor use only.
Never locate this appliance in an enclosed room, under a sealed• overhead structure, or in any type of enclosed area such as a ga-
rage, shed, or breezeway. Keep clear of trees and shrubs.
Do not place a side burner under or near windows or vents that• can be opened into your home.
Cal Flame side burners are not intended for installation in or on• recreational vehicles or boats.
Maintain sufcient distance as to not overheat any overhead com-• bustible material such as a patio cover.
The area surrounding your new side burner should be kept clean•
and free from ammable liquids and other combustible materials
such as mops, rags or brooms, as well as solvents, cleaning uids,
and gasoline.
Do not use the side burner or area surrounding the side burner•
as a storage area for ammable or plastic items. Do not store the
liquid propane (LP) cylinder in the vicinity of this or any other ap-
pliance when it is not being used.
Set-Up
We recommend that a licensed contractor install your Cal Flame• side burner. Installation must conform to local codes, or in the
absence of local codes, with either the National Fuel Gas Code,
ANSI Z223.1 / NFPA54, Natural Gas and Propane Installation
Code, CSA B149.1, or Propane Storage and Handling Code,
B149.2), as applicable.
To prevent re and smoke damage, remove all packaging material • before operating side burner.
Before you start cooking, clean the entire side burner thoroughly• with hot, soapy water. This is necessary to remove residual sol-
vents, oil and grease used in the manufacturing process. The
grates should also be thoroughly cleaned in the same manner.

2
Safety Instructions
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Operation
Do not use side burner for oth• er than intended use.
In the event that a burner goes out, turn burner knobs to the• full OFF position and let it air out. Do not attempt to use the side
burner until the gas has had time to dissipate.
Keep all electrical supply cords and the rotisserie motor cord away• from the heated areas of the side burner.
Never use the side burner in windy conditions. If used in a consis-• tently windy area a windbreak will be required. Always adhere to
the specied clearances listed in this manual.
Never line the side burner with aluminum foil.•
When the unit is not in use, be sure to turn off the gas at the• source.
When handling LP gas line and connectors, do not allow them to• come in contact with any metal surfaces of the cart or cabinet. Do
not drop LP connectors.
Do not use solid fuel such as charcoal briquettes.•
Never leave the side burner unattended when in use. When using• pots and pans, boil-overs will cause smoking and greasy boil-overs
may ignite.
Always use the proper size pan. Select utensils with at bottoms • large enough to cover the burner. The use of under-sized utensils
exposes the sides of the utensils to direct contact with a portion
of the ame. This can scorch utensils and hamper cleanup. Exces-
sive ames on large stainless steel pots can result in permanent
discoloration. For best results, we recommend commercial quality
aluminum pans and utensils.
Always position handles of utensils so they do not extend over ad-• jacent work areas or cooking areas. This reduces the risk of burns,
ignition of ammable materials, and spillage due to accidental con-
tact with the utensils.
Do not use water on grease res. Never pick up a aming pan. •
Turn the appliance off and smother the aming pan with a tight-
tting lid, a cookie sheet or a at tray. For aming grease outside
of the pan, smother it with baking soda or use a dry chemical or
foam-type re extinguisher.
Never allow clothing, pot holders or other ammable materials • come in contact with or be close to any grate, burner or hot sur-
face until it has fully cooled. Never wear loose tting or hanging

Safety Instructions
3
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
garments while using your side burner. Fabric may ignite and result
in personal injury.
Only use dry pot holders and do not use a towel or other bulky• cloth in place of pot holders. Moist or damp pot holders used on
hot surfaces can cause burns.
Do not heat any unopened glass or metal container of food on• the side burner. Pressure may build up and cause the container to
burst, possibly resulting in serious personal injury or damage to
the side burner.
Do not reach over your side burner when hot or in use.•
Maintenance and Repair
Spiders and other i• nsects can nest in the burners of the side burner
and block the gas and airow to the burner ports. This creates a
dangerous condition that can result in a re behind the valve pan-
el. Inspect and clean the burners periodically and follow the guide-
lines in the Cleaning and Maintenance section of this manual.
Unless specically recommended in this manual, do not repair or •
replace any part of the side burner. A qualied technician should
perform all service. Any repairs made by a non-L.M.S. approved
dealer technician will void your warranty.
Storage
When your side burner is not in use, turn off the gas at the supply• cylinder.
Precautions Regarding Children
Never leave children unattended in the area where the side burner• is being used. Close supervision of children is necessary when any
appliance is use near children.
Do not store items of interest to children in the side burner.•
Never allow children to sit or stand on any part of the side burner.•

4
Installation / Assembly
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Installation / Assembly
Most cities and counties require permits for exterior construction and
electrical circuits. In addition, some communities have codes requiring
residential barriers such as fencing and/or self-closing gates on prop-
erty to prevent unsupervised access to the property by children under
the age of ve. Your dealer can provide information on which permits
may be required and how to obtain them prior to the delivery of your
equipment.
We recommend the installation, adjustment and service of your new
side burner be performed by LMS qualied installers and service tech-
nicians to ensure proper operation and prevent accidents.
When planning your Cal Flame side burner location, access to gas lines
should be considered. The location with the shortest gas line run is
recommended.
When determining a suitable location, consider factors such as expo-
sure to wind, proximity to trafc paths, and windows that open into
the home.
Cabinet Cut-out Dimensions
Your Cal Flame side burner is de-
signed for easy installation into a
non-combustible enclosure. The
supporting deck or counter must
be at and level. When determin-
ing the nal location of your side
burner, adequate cross ventilation
must be present to prevent gas
from being trapped in the event of
a leak.
The drawing at right shows the dif-
ferent types of cabinet cut-out di-
mensions for slide-in side burners.
Model Description Width Depth Height
BBQ08954P Deluxe Side by Side Burner 25 ¼” 12 ½” 7 ¼”
BBQ08899P Deluxe Double Side Burner 12 ¼” 22” 7 ¼”
WIDTH DEPTH
HEIGHT

Installation / Assembly
5
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
WIDTH DEPTH
The drawing at right shows the
different types of cabinet cut-out
dimensions for drop-in side burn-
ers.
Gas Requirements and Connection
Gas Requirements and Connection
IMPORTANT: The Cal Flame side burner is manufactured to operate
on liquid propane (LP). However, it can be converted to operate on
natural gas (NG) by an authorized service technician. Consult your Cal
Flame dealer for information on converting your side burner.
Owners must not convert their side burners themselves. At-
tempting to convert the side burner from LP to NG may result
in serious injury and will void the warranty coverage.
If you do not have an updated ller valve on your existing propane tank,
you will need to purchase one at your local hardware store. Without it
you will not be able to attach your tank to your Cal Flame side burner
or rell the tank at your local propane rell station.
Model Description Width Depth
BBQ08953P Standard Side By Side Flat Burner 24 ¼” 19 ¾”
BBQ08852P Standard Single Flat Side Burner 11 ½” 17 ¾”

6
Installation / Assembly
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Leak Testing Procedure
Perform a leak test at least once a year whether the gas supply cyl-
inder has been disconnected or not. In addition, whenever the gas
cylinder is connected to the side burner or whenever any part of the
gas system is disconnected or replaced, perform a leak test.
As a safety precaution, remember to always leak test your side
burner outdoors in a well-ventilated area. Never smoke or permit
sources of ignition in the area while doing a leak test. Do not use
a ame, such as a lighted match to test for leaks. Use a solution of
soapy water.
Prepare a leak testing solution of soapy water by mixing in a1. spray bottle one part liquid soap to one part water.
Make sure all the control knobs are in the OFF position.2.
Turn on the gas.3.
Apply the leak-testing solution by spraying it on joints of the gas4. delivery system. Blowing bubbles in the soap solution indicates
that a leak is present.
Stop a leak by tightening the loose joint or by replacing the5. faulty part with a replacement part recommended by the manu-
facturer. Do not attempt to repair the cylinder valve if it is dam-
aged. The cylinder must be replaced.
Turn all control knobs back to the full OFF position.6.
If you are unable to stop a leak:
Turn all control knobs back to the full OFF position.1.
Shut off the gas supply to the side burner and release pressure2. in the hose and manifold by pushing in and turning any of the
control valves one quarter turn counter-clockwise.
On LP systems, remove the cylinder from the side burner.3.
Call an authorized gas appliance service technician or an LP gas4. dealer.
Do not use the appliance until the leak is corrected.

Installation / Assembly
7
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
LP Gas
Tank Requirements
For plumbed-in LP installation, use a convertible regulator and set it
for LP gas.
Maximum line pressure for plumbed-in propane is 14” WC (3.5 kPa).
Minimum line pressure for propane is 11” WC.
The side burner unit must be used with the gas pressure regulator. The
regulator will control and maintain a uniform gas pressure in the mani-
fold. The burner orices have been sized for the gas pressure delivered
by the regulator.
WARNING: Attempting to operate the side burner unit without the
gas regulator installed could cause an explosion and possible death.
CylinderSpecication
Any LP gas supply cylinder used with this side burner must be:
Constructed and marked in accordance with the• Specications
for LP-Gas Cylinders of the U.S. Department of Transportation
or the National Standard of Canada, CAN/CSA-B339, Cylin-
ders, Spheres and Tubes for Transportation of Dangerous
Goods; and Commission, as applicable.
Approximately 12 inches in diameter and 18 inches high.•
The maximum fuel capacity is 20 lbs. of propane, or 5 gallons. Full cyl-
inder weight should be approximately 38 lbs. (43.7 lbs. nominal water
capacity.) Never ll the cylinder beyond 80% full.

8
Installation / Assembly
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Place the dust cap on the cylinder valve outlet whenever the cylinder is
not in use. Only install the type of dust cap on the cylinder valve outlet
that is provided with the cylinder valve. Other types of caps or plugs
may result in leakage of propane.
LP Gas Hook Up
An enclosure for an LP gas cylinder shall be vented by openings at the
level of the cylinder valve and at oor level. The effectiveness of the
openings for purposes of ventilation shall be determined with the LP-
gas supply cylinder in place. This shall be accomplished in one of the
following manners:
One side of the enclosure shall be completely open.1.
Enclosures that have four sides, complete with a top and bottom:2.
At least two ventilation openings at cylinder valve level shall bea. provided in the sidewall, equally sized, spaced at 180º (3.14
rad), and unobstructed. Each opening shall have a total free
area of not less than one square inch per pound (7.1 cm²/kg)
of stored fuel capacity, and not less than a total free area of 10
square inches (64.5 cm²).
Ventilation openings shall be provided at oor level and shall b. have a total free area of not less than one square inch per
pound (7.1 cm²/kg) of stored fuel capacity and not less than
a total free area of 10 square inches (64.5cm²). If ventilation
openings at oor level are in a sidewall, there shall be at least
two openings. The bottom of the openings shall be at oor
level and the upper edge no more than 5 inches (127 mm)
above the oor. The openings shall be equally sized, spaced at
180º (3.14 rad) and unobstructed.
Every opening shall have minimum dimensions so as to permit c. the entrance of a 1/8 inch (3.2 mm) diameter rod.
Transporting and Storing LP Gas
Transport only one cylinder at a time. Ensure the cylinder is secured in
an upright position with the control valve turned off and the dust cap
in place. Store cylinders outdoors and out of reach of children. Do not
store cylinders in a building, garage, or any other enclosed area.

Installation / Assembly
9
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Natural Gas
Requirements
The installation of this appliance must conform with local codes or,
in the absence of local codes, to the national fuel gas code, ANSI
Z223.1a-1998. Installation in Canada must be in accordance with the
standard CAN/CGA-B149.2, Propane Installation Code.
A licensed contractor or local gas company representative must per-
form all natural gas connections.
Ensure that the service supplying the side burner is tted with a shut
off valve conveniently positioned near the side burner and giving ease
of access.
The side burner must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure testing
of the gas supply piping system at test pressures equal to or less than
0.5 psi (3.5 kPa).
The side burner and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of that
system at test pressure in excess of 0.5 psi (3.5 kPa).
Connection
Slide the side burner forward to gain access to the gas connection1. point in the rear.
Connect a suitable ex connector to the gas connection point.2. Check the side burner controls to ensure all control valves are in3. the full OFF position.
Turn on the main gas supply and check all connections for leaks4. using soapy water as described in the leak testing procedure sec-
tion.
Warning: If you see bubbles in the soapy solution at any of the connec-
tions, turn off the gas supply and tighten the connection. If tightening
the connection does not seal the leak, it may be necessary to replace
the ex hose.

10
Installation / Assembly
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Installing Side Burner with a Grill
If you are installing a side burner in conjunction with a gas grill, install
it in the following manner.
Assemble a 3/8” pipe nipple to the 3/8” pipe tee using Teon tape 1. or pipe sealant. Use only sealant that is approved for use on LP
gas.
Install the pipe tee assembly to the grill intake pipe. Tighten as-2. sembly and align the branch opening of the tee with the hole of
the cabinet.
Connect the exible hose (male end) to the pipe tee.3.
Install and secure the side burner into the island by simply setting4. it in place.
Connect the female end of the exible hose to the side burner 5. intake pipe.
Connect gas supply to the grill.6.
Check for gas leaks using soap water solution.7.

Installation / Assembly
11
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
C
B
A
BC
A
Connect the last open line to the side burner (Use gas rated tape seal
on all connections)
Then take other end of "T" adapter with hose attached and connect
to end of male located underneath and at the back of the grill. (Use
gas rated tape seal on all connections).
Open barbecue door. Install hose with regulator on propane tank.
Then connect the other end to "T" adapter. Make sure to use gas
rated tape seal when installing adapter to insure proper seal.
Grill
NOTE: You will need to use a gas rated sealer on gas connectors that are not flared.
To Propane Tank
3/8" Fittings
From Grill From Side Burner
"T" Adapter (3/8" Threaded)
To side burner, located
underneath behind burner.
To grill, located
underneath and
behind grill

12
UsingYour Side Burner
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Using Your Side Burner
Read all instructions before you
operate your side burner.
We recommend you wash your side burner with soap and water prior
to lighting it for the rst time. Oils are used during the manufacturing
process and some residual oil may still be on the stainless steel parts
of your side burner. Washing will reduce the possibility of discoloration.
We also recommend you keep your side burner covered when not in
use. This will minimize the amount of dust and dirt that accumulates on
your side burner and extend the life of your side burner.
Remember to use your Cal Flame side burner safely by following these
reminders:
It is dangerous to use side burners in any manner other than for• what it is designed for.
Do not use charcoal in a side burner.•
Do not heat sealed containers such as cans or jars on side burners.•
Explosion may result resulting in injury or death. Any sealed con-
tainer, such as a pressure cooker, must have a properly operating
pressure relieve valve to minimize explosion hazard.
Never put combustible material such as paper, cloth, or ammable • liquids on your side burner at any time. Do not use the side burner
to store ammable materials.
Lighting the Side Burner
Each time you light the side burner, check the following:
Inspect the hose before using the side burner. If there is excessive• abrasion or wear, or if the hose is cut, it must be replaced prior
to using the side burner. If you need a replacement hose, contact
your Cal Flame dealer.
Ensure the area around the barbecue is clear of ammable sub-• stances such as gasoline, yard debris, wood, etc.
Ensure there is no blockage of the airow through the vent space • located below the face of the unit.
When using propane gas:•
Keep the special ventilation openings in the enclosure• free and clear of debris.

UsingYour Side Burner
13
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
If connected to a propane cylinder, carefully inspect• the rubber hose attached to the regulator before each
use.
Ensure the propane cylinder, regulator, and rubber• hose are installed in a location not subject to heating
above 125º F (51º C).
Ensure the burner ames burn evenly along both sides of each •
burner with a steady ame (mostly blue with yellow tipping). If
burner ames are not normal, check the orice and burner for
insects or insect nests.
Ensure the in-line gas valve or gas cylinder valve is always shut • OFF when the side burner is not in use.
Do not operate the side burner with its cover closed or the back• burner with its cover installed.
Electronically Lighting the Side Burners
Open the hood.1.
Keep your face as far away from the burners as possible.2.
Rapidly rotate the burner knob counter clockwise past the light3. position to HIGH. You will hear a loud click as the electronic lighter
produces a spark.
Listen for the sound of the gas igniting. If the burner does not light4. on the rst try, repeat immediately.
If the burner does not light after three attempts, turn the control5. knobs to the OFF position. Wait ve minutes until the gas clears
before attempting to light it again.
Repeat the procedure or try the manual lighting procedure below.6.
Upon successful lighting, repeat the process on the other burners7. you wish to light.
To shut off the burners, rotate the knob and turn to OFF. It is nor-8. mal to hear a popping sound when the burners are turned off.

14
UsingYour Side Burner
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Manually Lighting the Side Burners
WARNING: Do not use standard matches or cigarette lighters to per-
form match lighting procedures. Serious burns can occur and lighters
can explode.
Open the hood.1.
If you have just attempted to light the burner, allow ve minutes 2. for any accumulated gas to dissipate.
Keep your face as far away from the burners as possible.3.
Light and insert a long stem match, holding it near the burner4. ports.
Push in and turn the control knob just past the LIGHT position to5. HIGH.
Listen for the sound of the gas igniting. If the burner does not6. light after ve seconds, turn the control knobs to the OFF position.
Wait ve minutes until the gas clears before attempting to light it
again.
If the burner does not light after several attempts see Trouble-7. shooting Guide in the back of this manual.
Basic Side Burner Operation
Before lighting, make sure all burner controls are off. Do not attempt
to light the burners if the smell of gas is present. Check the connection
with a soap and water solution after attaching the hose. For LP units,
make sure there is gas in the tank and it is sitting upright. For natural
gas units, make sure the shut off valve is on.
Light the side burners using the instructions on the previous1. page.
Place pots on the side burners and cook to desired completion.2. Adjust heat setting if necessary. You may set the control knob to
any position between HIGH and LOW.
Do not leave the side burner unattended while cooking.

Cleaning and Maintenance
15
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Cleaning and Maintenance
To ensure safe and proper maintenance, we recommend you follow
these directions carefully.
Clean the side burner regularly as determined by the amount of use
and foods cooked. In addition, keep the area around your side burner
clear and free from combustible materials, gasoline, and other am-
mable vapors and liquids. Do not obstruct the ow of combustion and
ventilation air.
These instructions describe the best way to care for your stainless
steel.
Although stainless steel will discolor and accumulate grime with regular
use, it can keep its original shine with periodic cleaning. We strongly
recommend using a surface protectant to prevent smudging and sur-
face rust from accumulating.
The easiest way to clean the side burner is immediately after cooking
is completed. Doing so will extend the life of your side burner, prevent
grease res, and present a pleasant appearance while you cook.
Stainless Steel Care and Cleaning
All exposed stainless steel surfaces require special attention if you want
to keep them looking clean and bright. Following these simple instruc-
tions will help avoid scratching or damaging the nish and keep your
stainless steel attractive.

16
Cleaning and Maintenance
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Cleaning Products and Materials
Avoid using these common cleaning products and materials – they
will damage the surface of your stainless steel.
CLR• Lime-Away• Oven cleaner• Cleansers such as Ajax or Comet• Ammonia• Bleach• Chlorine• Steel wool pads• Wire brushes• Scrapers• Pumice•
We recommend these products for cleaning your stainless steel:
Mild dish detergent such as Dawn• Formula 409• Fantastik•
Sheila Shine (exterior ONLY)•
WD-40 (exterior ONLY)•
We have had best success with Sheila Shine, but WD-40 works very
well too. Sheila Shine is available in some hardware stores; WD-40
is widely available.
Some people have reported that using baking soda, lemon oil, olive
oil, vinegar, or club soda can be effective for cleaning light soil on all
stainless steel surfaces.
Do not use steel wool or wire brushes to scrub your side burner.
For light soil, use a damp sponge or cloth. For heavier stains, use a
Scotch-Brite scrubber or similar product.

Cleaning and Maintenance
17
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Clean1.
Thoroughly clean stains, food, and grime using a sponge or damp
cloth with warm water and a mild dish soap. Use Fantastik or For-
mula 409 to remove heavier soil.
Rinse2.
Thoroughly rinse all surfaces and dry them completely with a clean
towel. Do not allow stainless steel to air dry.
Polish3.
We strongly recommend that you apply a surface protectant to all
exposed stainless steel surfaces.
Spray a small amount of WD-40 or Sheila Shine on a piece of paper
towel and rub with the grain over the surface of the appliance. Using
a clean terry cloth or paper towel, polish the appliance by rubbing
with the grain until excess liquid is removed and the surface shines. It
should not be oily to the touch, however some residue is acceptable.
Some people have reported that using lemon oil products such as Old
English furniture polish is effective for polishing stainless steel and pro-
tecting the surface.
Caution
Do not use WD-40 or Sheila Shine near food or on food
preparation surfaces as it is a health hazard.
Fire
Hazard
NEVER spray WD-40 or Sheila Shine near an open ame!
These products are extremely ammable while in their
aerosol forms.
Do not use a wire brush or stainless steel on any part of
your side burner!
Note

18
Cleaning and Maintenance
Cal Flame Side Burners
LTR50001082, Rev. B
www. c a l s p a s . c o m
Rust Removal
It is a common misconception that stainless steel does not rust. It does
not stain, corrode, or rust as easily as ordinary steel (it stains less),
but it is not stain-proof. If not properly protected and maintained, it
can corrode, pit, and discolor.
Important
Because salt will accelerate rust and corrosion, side
burner owners who live near the beach need to be dili-
gent in maintaining their stainless steel hardware. You
need to clean and polish your stainless steel frequently,
apply a protectant, and ensure water does not collect
and puddle.
Periodically clean exterior stainless steel surfaces with WD-40 or Sheila
Shine and wipe down with a dry cloth or paper towel until surface is
free of rust. If there is signicant rust or corrosion, use a Scotch-Brite
scrubber.
Both of these products will act as a surface protectant and help resist
smudges, stains, and rust.
Caution
Although nitric acid (also called aqua fortis) can be effec-
tive for rust removal, it is a highly corrosive chemical. Be-
cause of the potential for injury or damage to your stain-
less steel, we do not recommend using nitric acid.
Burner rack
The burner rack can all be removed for cleaning and is dishwasher
safe.
Use a solution equal parts detergent and hot water just as you would
for any cooking equipment. A stiff wire brush or steel wool may also be
helpful in removing grime and food deposits.
Covering Your Side Burner
When not in use and after cooling, cover your side burner with our
canvas cover. (See your local Cal Flame dealer for details.) The cover
will help protect your side burner from detrimental effects of weather
and environmental pollutants. Never put a cover on a hot side burner.
Allow the side burner to cool before covering.