CALI alumLEDs ALS600T-AD-AA-SM Series User manual

Manufactured in the U.S.A.
alumLEDs™
CALIFORNIA ACCENT LIGHTING, INC.
2820 E. Gretta Lane Anaheim, CA 92806
ph. 800.921.CALI (2254) | fx. 714.535.7902 | inf[email protected]om | calilighting.com
© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.
INSTALLATION
This document is issued in strict confidence on condition that it
is not used as a basis for manufacture or sale and is not copied,
reprinted, or disclosed to a third party either wholly or in part
without the prior written consent of California Accent Lighting, Inc.
Perspective End View Top View
2018.09.20 Rev 0
Page 1 of 2
ALS600T-AD-AA-SM-X
Add 0.93” to overall height for fixtures with louver installed
1. Measure area where ALS600T-AD will be installed.
Use a chalk line to ensure a straight installation.
4. Snap fixture into mounting bracket and install set screws on both sides.
Ensure fixture is secured in place, and spacing is accurate according to the
spacing diagram on page 2.
6. If applicable, connect disconnects between fixtures. Push and twist cap to lock
connector. Use a shrink tube to seal connector.
2. Determine number of mounting arms needed. Use a minimum of two mounting
arms per fixture. Mount arms 6” from center of mounting plate to end of fixture.
Refer to Spacing Diagram on page 2.
3. Mark location where mounting arms will be installed. Screw arms to desired
surface using proper drill bit for surface and screw size.
PUSH PUSH
PUSHPUSH
PUSH PUSH
PUSH PUSH
PUSH PUSH
Chalk line
20’
Assembled End View
1.5”
Shrink tube
1.5”
Apply heat
5. Loosen set screw until the mounting bracket can move freely. Turn the mounting
bracket until desired angle is achieved, then mate the locking bump with locking
hole. Refer to the angle increments diagram on page 2. Tighten set screw until
mounting bracket is secured in place.
2.61”
2.00”
X” (Specify Length)
3.23”
2.00”
X” (Specify Length)
3.11”
2.00”
X” (Specify Length)
4.13”
2.00”
X” (Specify Length)
2.61”
2.00”
X” (Specify Length)
3.23”
2.00”
X” (Specify Length)
3.11”
2.00”
X” (Specify Length)
4.13”
2.00”
X” (Specify Length)
Set screw
2.00”
4.61”
X” (Specify Length)
2.96”
2.00”
X” (Specify Length)
Set screw Mounting bracket
Locking hole
Locking bump
2.00”
4.61”
X” (Specify Length)
2.96”
2.00”
X” (Specify Length)

Manufactured in the U.S.A.
alumLEDs™
CALIFORNIA ACCENT LIGHTING, INC.
2820 E. Gretta Lane Anaheim, CA 92806
ph. 800.921.CALI (2254) | fx. 714.535.7902 | inf[email protected]om | calilighting.com
© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.
Page 2 of 2
INSTALLATION
This document is issued in strict confidence on condition that it
is not used as a basis for manufacture or sale and is not copied,
reprinted, or disclosed to a third party either wholly or in part
without the prior written consent of California Accent Lighting, Inc.
2018.09.20 Rev 0
ALS600T-AD-AA-SM-X
Mounting Arm Spacing Diagrams Angle Increments Diagram
-30°
-15°
0°
15°
30°
45°
60° 75° 90°
210°
195°
180°
165°
150°
135°
120°
105°
-30°
-15°
0°
15°
30°
45°
60° 75° 90°
210°
195°
180°
165°
150°
135°
120°
105°
90°
75°
60°
30°
0°
-30°
-60°
-75°
-90°
45°
15°
-15°
-45°
105°
90°
75°
60°
30°
0°
-30°
-60°
-75°
-90°
45°
15°
-15°
-45°
-105°
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
8’
3’
2’8”
1’8”
6” 6”
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
11’
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
8’
3’
2’8”
1’8”
6” 6”
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
11’
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
8’
3’
2’8”
1’8”
6” 6”
4’
3’8”
2’8”
6” 6”
Mounting Arms
4’
3’8”
2’8”
6” 6”
Mounting Arms
11’
EXAMPLE #1 (4’ Run)
EXAMPLE #2 (8’ Run = 4’ + 4’)
EXAMPLE #3 (11’ Run = 4’ + 4’ + 3’)