Callaway TITAN HITTING NET User manual

H
F
J
D
D
F
Image 1
Image 2
Firmly grab one end of Frame Pole ( H ), arc Frame Pole ( H ) (Image 1) and insert Corner Pin (G) into hollow end of Frame
Pole ( H ) ( Image 2 & 3). Do this for all four Frame Poles ( H ). Hitting net is now assembled and can be stood upright (Image 4).
Please refer to Titan Hitting Net images on the front of instructions, above the “KEY” for reference on how hitting net should look
standing upright.
To disassemble Hitting Net, reverse
steps 6 through 1.
Uninstall Hitting Target (A) and fold in
order to fit into Carry Case (M). Remove
all Metal Stakes (J) from ground.
Remove all Corner Pins (H) from
Frame Poles ( H ).
Remove Frame Poles ( H ) from Pole
Sleeves (C). Disassemble shock corded
Frame Poles ( H ).
Fold hitting net up and roll as tight as
possible in order to fit in Carry Case (K).
Place Hitting Net into Carry Case (K).
Add Frame Poles ( H ) to Carry Case (K).
Last Add Metal Stakes (J) and Hitting
Target (A) to Carry Case (K).
To secure net to ground push Metal Stakes (J) firmly through Anchor Stake
Loops (E) into ground. In order to add extra stability to hitting net, untie Anchor
Stake Draw String (F). Pull opposite end of Anchor Stake Draw String (F) that
has plastic piece attached, at a 45 degree angle away from the hitting net until
draw string is tight (Image 1). Insert Metal Stake (J) through loop of string that is
threaded through plastic piece of Anchor Stake Draw String (F) (Image 2).
Push Metal Stake (J) firmly into ground at a 45 degree angle away from hitting
net (Image 2). To adjust Anchor Stake Draw String (F) length pull plastic piece
attached to Anchor Stake Draw String (F) toward or away from hitting net.
1.
2.
3.
4.
5.
6.
7.
To install the Hitting Target (A), thread one end of the string attached to the
target through the Target Grommets (D) (Image 1 & 2). Then thread the end
back through the cord lock, by squeezing the lock between your thumb and
forefinger to open the string hole shown shown with the orange arrows above
(Image 2). Adjust accordingly for desired target height (Image 3).
step 4
step 5
step 6
SET UP INSTRUCTIONS (continued)
H
H
G
G
H
G
Image 2 Image 3
E
Image 3Image 2Image 1
D D
A
FOR MORE INFORMATION PLEASE VISIT WWW.callawaytag.COM OR CALL 1-800-456-2129
STORAGE INSTRUCTIONS
K
Image 1 Image 4
E
G
E

TITAN
™
HITTING NET INSTRUCTIONS
Unroll hitting net and lay flat on floor. Make sure
Pole Sleeves (C) are on top of net.
Assemble both Frame Poles ( H )
by interlocking shock-corded poles.
A. Hitting Target
B. Mesh Base
C. Pole Sleeves (2)
D. Target Grommets (2)
E. Anchor Stake Loops (4)
F. Anchor Stake Draw Strings (4)
A
B
C
D
E
F
G
H
I
J
C
D
E
F
F
G
HHH
B
E E
G G
C
D
K
H
G. Corner Pins (4)
H. Frame Poles (2)
I. Hitting Net
J. Stakes (8)
K. Carry Case
KEY: INCLUDES:
H
step 1 step 3
step 2
SET UP INSTRUCTIONS
H
C
Image 2
Image 1
Slide one Frame Pole ( H ) through one end of the Pole
Sleeve (C) circled in YELLOW (Image 1 left)(Image 2
above), through to the opposite end of the Pole Sleeve
(C), follow the RED arrow (Image 1 left). You should be
able to see both ends of the pole now. Now slide other
Frame Pole ( H ) through the 2nd Pole Sleeve (C) circled
in YELLOW (Image 1 left)(Image 2 above), through to the
opposite end of the Pole Sleeve (C), follow the RED
arrow (Image 1 left). You should be able to see all ends
of the Frame Poles ( H ) now.
C
C
C
C
HH
C