TiiTENT TB300 User manual

Pole: 7001 Aluminum Alloy
Material: Tear-resistant 75D Polyester with silicone treatment on the surface
Water pressure resistant: 3000mm
Minor pole
11mm 11-section
X 2
Main pole
13mm 12-section
X 2
1. Content
All TB300 contents are in one carry-on bag.
Outertent
Innertent
Pole Bag
Peg Bag
Topreventbreakage,makesure
thatthepolejointsarefirmly
connectedbeforeproceeding.

2. Dimension
400400400
150150150 100100100 150150150
300300300
225225225
280280280
220220220
195195195
150150150
250250250
170
cm
Inner tent and outer tent ratio diagram
The top of the inner tent's front door
on both sides has red elastic cords.
Outer tent size
Inner tent size
Door
T window
A window W window

3. Set up the tent
Spread out the outer tent and lay it flat, find the X-shaped pole sleeve (red
mark), and then insert the main pole (red mark) into the sleeve.
After both main poles are inserted into the pole sleeves, secure each end
with the corresponding fork buckle and pole clip.
１
２
４３
２１

Next, arch one of the main poles and secure the other end of the main pole.
３
Finally, arch the other main pole. At this time, the outer tent will stand up at the
same time. Then slowly make fine adjustments, and finally secure the pole and
the fork buckle.
４
After the 2 main poles are assembled,
the outer tent is now in a freestanding
state. Slightly tidy up its appearance.
５
１
２
１
２

Pass the minor pole through the sleeve of the wing, and then connect both
sides of the minor pole with the fork buckle.
６
１
２３
Then, handle the pole on
the opposite side in the
same manner.
7
8
Secure all pole clips on the poles.
Use pegs to secure the four corners.

First wrap a strap around the intersection of the poles, then stake down the
wind ropes.
9
The W window top has three
wind ropes, all staked down.
10
Each pole sleeve has two wind ropes, a total of eight places, all staked down.
11

The side with the red elastic cord is the direction of the front door of the
inner tent.
12
13 TB300 uses a symmetrical design and does not distinguish between front
and back. After selecting the direction of the front door, first hang the red
elastic cord, then fix the other hanging points on the back door, and finally
fix the bottom hooks on the metal ring of the fork buckle to complete the
installation.

4.Space
Whether it's the tent door, T window, W window, or A window,
they can all be opened to increase ventilation.
Hatchback models can directly
position the rear of the car near
the tent door and use it as a
tailgate tent.
As the tent door is wider, it's
recommended to roll up the
door panel and screen door
separately for easier storage.
door panel
screen door
After using the inner tent, there is still a vestibule space available for use.
The inner tent space is sufficient to accommodate four adults.

5.Pack away the tent
Spread out the outer tent, lift it at four points,
and pull outwards at the midpoint on both
sides (where the triangle is indicated).
１
After lifting it, level it out and place it on the ground.
２
１
１
２
Fold both sides inward.
３
１
2

Fold inward again.
４
Fold.
6
Place the inner tent.
7Roll up.
8
Pack it into the bag.
9
Fold again.
５

6 . Note
1. When using the product, make sure all pegs and wind-resistant guy
lines are fastened so the tent can provide the best performance.
2. This product is not flame resistant. Do not light a fire inside the tent
in case any irreversible or irreparable damage is caused. Be careful
of fire, lack of oxygen, and carbon monoxide poisoning when using
heaters in the tent. Please set up the tent in a location with good
ventilation and drainage and without natural and manned disasters.
3. Be aware of the weather. Please leave the campsite for a safe
location in accordance to your evacuation plan if the weather gets
bad. In the case of inclement weather or strong winds, please check
your tent thoroughly to make sure all pegs and guy lines are
fastened.
4. Before using the tent for the first time, please try to set up the tent
and confirm the accessories and the steps for setting up the tent. To
ensure the tent is used appropriately, please learn and understand
how to use it. Please contact the vendor for any malfunctions.
5. When the temperature inside the tent is higher than the outside,
water vapor will change into liquid water when it hits the wall of the
flysheet and form droplets. This process is called condensation.
Please keep the tent well ventilated to reduce this phenomenon.
6. The bottom end of the two rows of the door zipper is slightly
unequal in length due to the manufacturing process. Do not pull the
zipper too hard in case of damage.
7. Despite the good ventilation of the tent, it is not fully condensation-
proof. Depending on the location of the site, condensation may
occur inside the tent. Make sure the tent is properly ventilated.

Emergency Responses
With proper use and maintenance, the TiiTENT product can stay in
good quality. Please be aware of the following important
information to prevent damage to the product:
1. Accidents may damage the poles and fabric. Please bring repair kits
(duct tape, guy lines, and tubes for reinforcements) with you at all
times for immediate use.
2. If damage to the product is not fixed immediately, it may result in
serious and even irreparable harm. If the fabric is torn or broken,
please place duct tape over both sides of the fabric to prevent the
damage from spreading or remove the damaged fabric.
3. Prolonged exposure to sunlight can cause colors to fade, weakening
the strength of the fabric. Please bear in mind that the tent is not
intended for use in prolonged settings in which they remain
exposed to the sun. When the degradation caused by sunlight
exceeds the endurance limit of the fabric, the damage will become
permanent.
4. If the product is constantly damp, mold, stinky smells, color bleed,
or fabric degradation may occur. Therefore, please make sure the
product is fully dry before attempting to store it.
5. If the fabric becomes moldy due to humidity, the mildew might not
be removed. However, please remove the mold on the surface and
disinfect the fabric with alcohol. If the fabric is damaged by mold,
leakage will occur.

Our products have undergone a rigid quality control
process. Our warranty covers all the defects derived
from errors during production; however, the
following problems are not covered by our warranty.
Sorry for the inconvenience.
1. Damage caused by unexpected incidents.
2. Damage due to improper use or undue force.
3. Degradation of the materials over time or due to
exposure to UV light.
4. Damage caused by defects not associated with
production.
5. Damage from remodeling.
Conditions Not Covered by our Warranty
If you have any questions regarding the
warranty, please contact the retailer where
you have bought the product from for after-
sales services.

V.202305
Tsair Yih Industrial Co., Ltd.
No.5, Xingye St., Xiaogang Dist.,
Kaohsiung City 812, Taiwan
[email protected]
TEL:[phone]