Candy FIDCP X625 L User manual

BUILT-IN OVENS
33703582 FIDCP X625 L
Manual de servicio

33703582 FIDCP X625 L 9953(31/12/2099)
Ref Descripción Código Inicio Fin
7 Pared aislante trasera 42818378
24 Bandeja horno ( grasera ) 42834451
25m Parrilla corredera telescopica 42822692
27 Panel de mandos 70010634
50 Aislamiento 70006664
77b Termostato de seguridad 70006008
78b Mando 42819098
78f Alojamiento mando 42812922
79s Marco mando 42812925
85a Termostato electrico 42833528
90a Conmutador horno electric 42837376
102d Programador 42839776
104 Boquilla horno 42823856
106q Lampara piloto 91101256
116 Resistencia grill electr. 42839626
119 Resistencia infer. horno 42827837
120 Repisa para resistencia 42831725
131 Caja conexiones 42370401
132 Motoventilador 42837772
136 Proteccion helice 42835638
157d Soporte derecho bisagra 42835067
157e Soporte izquierdo bisagra 42835066
173a Junta cuatro latos 42836938
176 Vidrio int. puerta horno 42837904
178 Vidrio puerta horno 70007795
179 Asa puerta horno 42821363
179e Casquillo 42801989
182g Transportador cierre vidr 42817394
184 Bisagra puerta horno 42836536
185 Soport.bisagr.puert.horno 42808792
225 Parrilla lateral horno 42838757
233 Casquillo distanciador 41030746
287 Ventilador 70006946
287d Termostato ventilador 41010134
300 Tapa superior 42838955
302a Cobertura inferior 42817761
304a Cobert.lateral drch.horno 42838930
304b Cobert.lateral izqd.horno 42838929
491 Cable alimentacion 42827352
999 Esquema de principio 42827049
1036 Distanciador 42834121
1207 Soporte 42826679

CANDY HOOVER GROUP Via Comolli 16 Brugherio – Italy
User Instructions
Mode d’emploi
Bedienungsanleitung
Istruzioni per l’uso
OVENS
FOURS
ÖFEN
FORNI
2
16
44
30
EN
FR
DE
IT
Instrucciones de uso
Handleiding
Instruções para o utilizador
HORNOS
OVENS
FORNOS
58
72
86
ES
NL
PT

EN 2
Safety Indications
General Instructions
Product description
Display description
Cooking Modes
General notes on cleaning
Maintenance
Troubleshooting
Installation
Summary
3
7
9
10
12
13
13
15
100

EN 3
• During cooking, moisture may condense inside the oven cavity
or on the glass of the door. This is a normal condition. To reduce
this eect, wait 10-15 minutes after turning on the power be-
fore putting food inside the oven. ln any case, the condensation
disappears when the oven reaches the cooking temperature.
• Cook the vegetables in a container with a lid instead of an open
tray.
• Avoid leaving food inside the oven after cooking for more than
15/20 minutes.
• WARNING: the accessible parts can become hot when the oven
is in use. Young children should be kept at a safe distance.
• WARNING: the accessible parts can become hot when the grill
is in use. Children should be kept at a safe distance.
• Disconnect the appliance from the mains electricity supply be-
fore carrying out any work or maintenance.
• WARNING: in order to avoid any danger caused by the acciden-
tal resetting of the thermal interruption device, the appliance
should not be powered by an external switching device, such as
a timer, or be connected to a circuit that is regularly switched on
and o.
• Children under 8 should be kept at a safe distance from the ap-
pliance if not continuously supervised.
• Children should not play with the appliance.
• The appliance can be used by those aged 8 or over and by those
with limited physical, sensorial or mental capacities, without
experience or knowledge of the product, only if supervised or
provided with instruction as to the operation of the appliance,
in a safe way with awareness of the possible risks.
• Cleaning and maintenance should not be carried out by unsu-
pervised children.
• Do not use rough or abrasive materials or sharp metal scrapers
to clean the oven door glasses, as they can scratch the surface
Safety Indications

EN 4
and cause the glass to shatter.
• The oven must be switched o before removing the removable
parts. After cleaning, reassemble them according the instruc-
tions.
• Only use the meat probe recommended for this oven.
• Do not use a steam cleaner or high pressure spray for cleaning
operations.
• IF THE OVEN IS PROVIDED BY THE MANUFACTURER WITH-
OUT PLUG:
THE APPLIANCE MUST NOT BE CONNECTED TO THE POW-
ER SOURCE USING PLUG OR SOCKETS, BUT MUST BE DI-
RECTLY CONNECTED TO THE SUPPLY MAINS. The con-
nection to the power source must be carried out by a suitably
qualied professional. In order to have an installation compliant
to the current safety legislation the oven must be connect-
ed only placing an omnipolar breaker, with contact separation
compliant to the requirements for overvoltage category III,
between the appliance and the power source. The omnipolar
breaker must bear the maximum connected load and must be
in line with current legislation. The yellow-green earth cable
should not be interrupted by the breaker. The omnipolar break-
er used for the connection must be easily accessible when the
appliance is installed.
The connection to the power source must be carried out by a
suitably qualied professional considering the polarity of the
oven and of the power source.
The disconnection must be achieved incorporating a switch in
the xed wiring in accordance with the wiring rules
• IF THE OVEN IS PROVI ED BY THE MANUFACTURER WITH
PLUG:
The socket must be suitable for the load indicated on the tag
and must have ground contact connected and in operation.
The earth conductor is yellow-green in colour. This operation
should be carried out by a suitably qualied professional. ln case

EN 5
of incompatibility between the socket and the appliance plug,
ask a qualied electrician to substitute the socket with another
suitable type. The plug and the socket must be conformed to
the currentnormsofthe installation country.Connectiontothe
power source can also be made by placing an omnipolar break-
er, with contact separation compliant to the requirements for
overvoltage category III, between the appliance and the pow-
er source that can bear the maximum connected load and that
is in line with current legislation. The yellow-green earth cable
should not be interrupted by the breaker. The socket or omnip-
olar breaker used for the connection should be easily accessi-
ble when the appliance is installed.
The disconnection may be achieved by having the plug accessi-
ble or by incorporating a switch in the xed wiring in accordance
with the wiring rules.
• lf the power cable is damaged, it should be substituted with a
cable or special bundle available from the manufacturer or by
contacting the customer service department. The type of pow-
er cable must be H05V2V2-F. This operation should be carried
out by a suitably qualied professional. The earth conductor
(yellow-green) must be approximately 10 mm longer than the
other conductors. For any repairs, refer only to the Customer
Care Department and request the use of original spare parts.
• Failure to comply with the above can compromise the safety of
the appliance and invalidate the guarantee.
• Any excess of spilled material should be removed before clean-
ing.
• A long power supply failure during an occurring cooking phase
may cause a malfunction of the monitor. ln this case contact
customer service.
• The appliance must not be installed behind a decorative door in
order to avoid overheating.
• When you place the shelf inside, make sure that the stop is di-
rected upwards and in the back of the cavity. The shelf must be

EN 6
inserted completely into the cavity.
• When inserting the grid tray pay attention that the anti-slide
edge is positioned rearwards and upwards.
• WARNING: Do not line the oven walls with aluminium foil or sin-
gle-use protection available from stores. Aluminium foil or any
other protection, in direct contact with the hot enamel, risk
melting and deteriorating the enamel of the insides.
• WARNING: Never remove the oven door seal.
• CAUTION: Do not rell the cavity bottom with water during
cooking or when the oven is hot.
• No additional operation/setting is required in order to operate
the appliance at the rated frequencies.
• The oven can be located high in a column or under a worktop.
Before xing, you must ensure good ventilation in the oven
space to allow proper circulation of the fresh air required for
cooling and protecting the internal parts. Make the openings
specied on last page according to the type of tting.
• For a correct use of the oven it is advisable not to put the food in
direct contact with the racks and trays, but to use oven papers
and / or special containers.

EN 7
General Instructions
Safety Indications
We thank you for choosing one of our products. For the best results with your oven, you should
read this manual carefully and retain it for future reference. Before installing the oven, take note
of the serial number so that you can give it to customer service sta if any repairs are required.
Having removed the oven from its packaging, check that it has not been damaged during trans-
portation. If you have doubts, do not use the oven and refer to a qualied technician for advice.
Keep all of the packaging material (plastic bags, polystyrene, nails) out of the reach of children.
When the oven is switched on for the rst time, strong smelling smoke can develop, which is
caused by the glue on the insulation panels surrounding the oven heating for the rst time. This
is absolutely normal and, if it occurs, you should wait for the smoke to dissipate before putting
food in the oven. The manufacturer accepts no responsibility in cases where the instructions
contained in this document are not observed.
NOTE: the oven functions, properties and accessories cited in this manual will vary, depending
on the model you have purchased.
Only use the oven for its intended purpose, that is only for the cooking of foods; any other use, for
example as a heat source, is considered improper and therefore dangerous. The manufacturer
cannot be held responsible for any damage resulting from improper, incorrect or unreasonable
usage.
The use of any electrical appliance implies the observance of some fundamental rules:
- do not pull on the power cable to disconnect the plug from the socket;
- do not touch the appliance with wet or damp hands or feet;
- in general the use of adaptors, multiple sockets and extension cables is not recommended;
- in case of malfunction and/or poor operation, switch o the appliance and do not tamper with it.
Electrical Safety
ENSURE THAT AN ELECTRICIAN OR QUALIFIED TECHNICIAN MAKES THE ELECTRICAL
CONNECTIONS. The power supply to which the oven is connected must conform with the
laws in force in the country of installation. The manufacturer accepts no responsibility for any
damage caused by the failure to observe these instructions. The oven must be connected to
an electrical supply with an earthed wall outlet or a disconnector with multiple poles, depending
on the laws in force in the country of installation. The electrical supply should be protected with
suitable fuses and the cables used must have a transverse section that can ensure correct sup-
ply to the oven.
CONNECTION
The oven is supplied with a power cable that should only be connected to an electrical supply
with 220-240 Vac power between the phases or between the phase and neutral. Before the oven
is connected to the electrical supply, it is important to check:
- power voltage indicated on the gauge;
- the setting of the disconnector.

EN 8
The grounding wire connected to the oven’s earth terminal must be connected to the earth ter-
minal of the power supply.
WARNING
Before connecting the oven to the power supply, ask a qualied electrician to check the conti-
nuity of the power supply’s earth terminal. The manufacturer accepts no responsibility for any
accidents or other problems caused by failure to connect the oven to the earth terminal or by an
earth connection that has defective continuity.
NOTE: as the oven could require maintenance work, it is advisable to keep another wall socket
available so that the oven can be connected to this if it is removed from the space in which it is
installed. The power cable must only be substituted by technical service sta or by technicians
with equivalent qualications.
A low light around the central main switch could be present when the oven is o. This is a normal
behavior. I can be removed just turning the plug upside down or swapping the supply terminals.
Recommendations
Installation
After each use of the oven, a minimum of cleaning will help keep the oven perfectly clean.
Do not line the oven walls with aluminium foil or single-use protection available from stores. Al-
uminium foil or any other protection, in direct contact with the hot enamel, risks melting and de-
teriorating the enamel of the insides. In order to prevent excessive dirtying of your oven and the
resulting strong smokey smells, we recommend not using the oven at very high temperature. It
is better to extend the cooking time and lower the temperature a little. In addition to the acces-
sories supplied with the oven, we advise you only use dishes and baking moulds resistant to very
high temperatures.
The manufacturers have no obligation to carry this out. If the assistance of the manufacturer is
required to rectify faults arising from incorrect installation, this assistance is not covered by the
guarantee. The installation instructions for professionally qualied personnel must be followed.
Incorrect installation may cause harm or injury to people, animals or belongings. The manufac-
turer cannot be held responsible for such harm or injury.
The oven can be located high in a column or under a worktop. Before xing, you must ensure good
ventilation in the oven space to allow proper circulation of the fresh air required for cooling and
protecting the internal parts. Make the openings specied on last page according to the type of
tting.

EN 9
1. Control panel
2. Shelf positions (lateral wire
grid if included)
3. Grids
4. Trays
5. Fan (if present)
6. Oven door
7. Lateral wire grids (if present:
only for at cavity)
8. Serial number
Product description
ACCESSORIES
Drip tray Metal grid
Collects residues that drip when cooking food
on the grills. Holds baking trays and plates.
Lateral wire grids (only if present)
Located on both sides of the oven cavity, holds
metal grills and drip pans.
1
2
7
3
8
4
6
5
First Use
PRELIMINARY CLEANING; Clean the oven before using for the rst time. Wipe over external surfaces
with a damp soft cloth. Wash all accessories and wipe inside the oven with a solution of hot water and
washing up liquid. Set the empty oven to the maximum temperature and leave on for about 1 hour, this
will remove any lingering smells of newness.

EN 10
Display description
1. Minute minder
2. Clock setting
3. Cooking time
4. Child Lock
5. Temperature or clock display
6. LCD display adjustment controls
7. Thermostat selector knob
8. Function selector knob
WARNING: the rst operation to carry out
after the oven has been installed or following
the interruption of power supply (this is re-
cognizable the display pulsating and showing
12:00 ) is setting the correct time. This is achie-
ved as follows.
•Push the central button 4 times
•Set time with “-” “+” buttons.
•Release all buttons.
ATTENTION: The oven will only operate pro-
viding the clock is set.
87
1 3
5
6
2 4

EN 11
FUNCTION HOW TO ACTIVATE HOW TO
DEACTIVATE WHAT IT DOES WHY IT IS NEEDED
KEY LOCK
Child Lock function
is activated by
touching Set (+)
for a minimum of 5
seconds. From this
moment on all other
function are locked
and the display will
ash STOP and
preset time inter-
mittently. From this
moment on all other
functions are locked,
LED of child lock
turn on, the display
will ash STOP and
present time inter-
mittently
Child Lock function
is deactivated by
touching touchpad
Set (+) again for a mi-
nimum of 5 seconds.
From this moment
on all functions are
selectable again.
From this moment
LED of child lock turn
o and all functions
are selectable again.
MINUTE
MINDER
Push the central
button
1 times
Press the buttons
“-” “+”
to set the required
time
Release all the
buttons
When the set time
as elapsed an audible
alarm is activated
(this alarm will stop
on its own, however
it can be stopped
immediately by
pressing the button)
SELECT.
Sounds an alarm at
the end of the set
time.
During the process,
the display shows
the remaining time.
Allows to use the oven
as alarm clock (could be
activated either with ope-
rating the oven or with
out operating the oven)
COOKING
TIME
Push the central
button 2 times
Press the buttons
“-” or “+”to set the
lenght of cooking
required
Release all buttons
Set the cooking
function with
the oven function
selector
Push any button to
stop the signal. Push
the central button to
return to the clock
function.
It allows to preset
the cooking time
required for the
recipe chosen.
To check how long
is left to run press
the SELECT button
2 Times.
To alter/change the
preset time press
SELECT and “-” “+”
buttons.
When the time is elapsed
the oven will switch o
automatically.
Should you wish to stop
cooking earlier either turn
the function selector to 0,
or set time to 0:00
(SELECT and “-” “+”
buttons)

EN 12
Cooking Modes
* Tested in accordance with the EN 60350-1 for the purpose of energy consumption declaration and energy class.
Symbol
T °C
de-
fault
T °C
range Function
LAMP: Turns on the oven light.
DEFROST: When the dial is set to this position. The fan circulates air at
room temperature around the frozen food so that it defrosts in a few min-
utes without the protein content of the food being changed or altered.
180
210
50 ÷ MAX
MULTI-LEVEL: We recommend you use this method for poultry, pastries,
sh and vegetables. Heat penetrates into the food better and both the
cooking and preheating times are reduced. You can cook dierent foods
at the same time with or without the same preparation in one or more po-
sitions. This cooking method gives even heat distribution and the smells
are not mixed.
Allow about ten minutes extra when cooking foods at the same time.
190 50 ÷ MAX
* COOK LIGHT: This function allows to cook in a healthier way, by re-
ducing the amount of fat or oil required. The combination of heating ele-
ments with a pulsating cycle of air ensures a perfect baking result.
210 50 ÷ MAX
BOTTOM HEATING + FAN: The bottom heating element is used with the
fan circulating the air inside the oven. This method is ideal for juicy fruit
ans, tarts, quiches and pâté.
It prevents food from drying and encourages rising in cakes, bread dough
and other bottom-cooked food.
Place the shelf in the bottom position.
220 50 ÷ MAX
* CONVENTIONAL: Both top and bottom heating elements are used.
Preheat the oven for about ten minutes. This method is ideal for all tradi-
tional roasting and baking. For seizing red meats, roast beef, leg of lamb,
game, bread, foil wrapped food (papillotes), aky pastry. Place the food
and its dish on a shelf in mid position.
230 50 ÷ MAX
GRILL : use the grill with the door closed.
The top heating element is used alone and you can adjust the temper-
ature. Five minutes preheating is required to get the elements red-hot.
Success is guaranteed for grills, kebabs and gratin dishes. White meats
should be put at a distance from the grill; the cooking time is longer, but
the meat will be tastier. You can put red meats and sh llets on the shelf
with the drip tray underneath.
220 50 ÷ MAX PIZZA - With this function hot air circulated in the oven to ensure perfect
result for dishes such as pizza or cake.