Candy CSE H8A2LE User manual

EN

!
2
Thank you for choosing this product.
We are proud to offer the ideal product for
you and the best complete range of home
appliances for your daily routine.
Please read and follow these
instructions carefully and operate the
machine accordingly. This booklet provides
important guidelines for safe use,
installation, maintenance and some useful
advice for best results when using your
machine. Keep all documentation in a safe
place for future reference or for any future
owners.
Please check that the following items are
delivered with the appliance:
•Instruction manual
•Guarantee card
•Energy label
Check that no damage has occurred to the
machine during transit. If it as, call for
service by Customer Service Centre.
Failure to comply with the above can
compromise the safety of the appliance.
You may be charged for a service call if a
problem with your machine is caused by
misuse or by incorrect installation.
To contact the Service, ensure that you
have the unique 16-character code
available, also called the "serial number".
This code is a unique code for your
product, printed on the sticker that can be
found inside the door opening.
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components (which can
be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials. Individuals can
play an important role in ensuring that WEEE
does not become an environmental issue; it is
essential to follow some basic rules:
!WEEE should not be treated as household
waste;
!WEEE should be handed over to the relevant
collection points managed by the municipality or
by registered companies. In many countries, for
large WEEE, home collection could be present.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
1. GENERAL SAFETY RULES
2. DRAIN HOSE KIT
3. WATER CONTAINERS
4. DOOR, FILTERS AND HEAT
EXCHANGER
5. PRACTICAL HINTS
6. QUICK USER GUIDE
7. CONTROLS AND PROGRAMMES
8. TROUBLESHOOTING AND WARRANTY
This appliance is marked according to
the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
Contents
Environmental conditions

!
EN
3
1. GENERAL SAFETY
RULES
!This appliance is intended to
be used in household and
similar applications such as:
- Staff kitchen areas in shops, offices
and other working environments;
- Farm houses;
- By clients in hotels, motels and
other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
!This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
!Children should be supervised
to ensure that they do not play
with the appliance.
!Children of less than 3 years
should be kept away unless
continuously supervised.
!This machine is solely for
domestic use, i.e. to dry
household textiles and garments.
!Ensure that the instructions for
installation and use are fully
understood before operating
the appliance.
!Do not touch the appliance
when hands or feet are damp
or wet.
!Do not lean on the door when
loading the machine or use the
door to lift or move the machine.
!Do not continue to use this
machine if it appears to be faulty.
WARNING
Misuse of a tumble dryer may
create a fire hazard.

!
4
!The tumble dryer is not to be
used if industrial chemicals
have been used for cleaning.
! Lint and fluff must not be allowed
to collect on the floor around the
outside of the machine.
!Always remove the plug before
cleaning the appliance.
!The drum inside may be very
hot. Always allow the dryer to
complete the cool down period
before removing the laundry.
!The final part of a tumble dryer
cycle occurs without heat (cool
down cycle) to ensure that the
items are left at a temperature
that ensures that the items will
not be damaged.
WARNING
Do not use the product if the
fluff filter is not in position or
is damaged; fluff could be
ignited.
WARNING:
Where the hot surface
symbol is located the
temperature rise during
operation of the tumble
dryer may be in excess of 60
degrees C.
WARNING
Never stop a tumble dryer
before the end of the drying
cycle unless all items are
quickly removed and spread
out so that the heat is
dissipated.
WARNING
During transport ensure that
the dryer is in an upright
position, if it's necessary
you can only flip in the side
shown.
If the product is in different
side, wait at least 4 hours
before switching on so that
the oil can flow back into the
compressor. Failure to do
this could result in damage
to the compressor.

!
EN
5
!Do not install the product in a
low temperature room or in a
room where there is a risk of
frost occurring. At temperature
around freezing point the
product may not be able to
operate properly: there is a risk
of damage if the water is
allowed to freeze in the
hydraulic circuit (valves, hoses,
pumps). For a better product
performance the ambient room
temperature must be between
5-35°C. Please note that
operating in cold condition
(between +2 and +5°C) might
simply some water condensation
and water drops on floor.
!In cases where the dryer is
installed on top of a washing
machine, a suitable stacking kit
must be used according to the
configuration of your appliance:
- Stacking kit "standard size": for
washing machine with
minimum depth of 44 cm;
- Stacking kit "slim size": for
washing machine with
minimum depth of 40 cm.
- Universal stacking kit with
sliding: for washing machine
with minimum depth of
47 cm.
The stacking kit shall be
obtainable from service. The
instructions for installation and
any fixing attachments, are
provided with the stacking kit.
!NEVER install the dryer up
near curtains.
!The appliance must not be
installed behind a lockable door,
a sliding door or a door with a
hinge on the opposite side to
that of the tumble dryer, in
such way that a full opening of
the tumble dryer door is restricted.
!For your safety, the appliance
must be correctly installed. If
there is any doubt about installation,
call Service for advice.
!Once the machine is in place
the feet should be adjusted to
ensure that the machine is
level.
!The technical details (supply
voltage and power input) are
indicated on the product rating
plate.
Installation
Electrical connections and
safety instructions

!
6
!Make sure that the electrical
system is earthed, complies
with all applicable law and that
the (electricity) socket is
compatible with the plug of the
appliance. Otherwise, seek
qualified professional assistance.
!Do not use adapters, multiple
connectors and/or extensions.
!The plug should be accessible
for disconnection after the
appliance has been installed.
!Do not plug the machine in and
switch it on at the mains until
the installation is completed.
!If the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
!Adequate ventilation must be
provided in the room where the
tumble dryer is located to
prevent gases from appliances
burning other fuels, including
open fires, being drawn into
the room during operation of
the tumble dryer.
!Install the rear of the appliance
close to a wall or vertical surface.
!There should be a gap of at
least 12 mm between the
machine and any obstrubtions.
The inlet and outlet air should
be kept clear of obstruction.
!Make sure carpets or rugs
do not obstruct the base or any
of the ventilation openings.
!Prevent items from falling or
collecting behind the dryer as
these may obstruct the air inlet
and outlet.
!Exhaust air must not be
discharged into a flue which is
used for exhausting fumes
from appliances burning gas or
other fuels.
!Check regularly that the air
flowing around the dryer is not
restricted, avoiding accumulation
of dust and lint.
WARNING
The appliance must not be
supplied through an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on
and off by a utility.
Ventilation

!
EN
7
!Check frequently the fluff filter
after use, and clean, if necessary.
!Always refer to the laundry
care labels for directions on
suitability for drying.
!Fabric softeners, or similar
products, should be used as
specified by the fabric softener
instructions.
!Do not dry unwashed items in
the tumble dryer.
!Clothes should be spin dried or
thoroughly wrung before they
are put into the tumble dryer.
!Clothes that are dripping wet
should not be put into the dryer.
!Glass fibre curtains should
NEVER be put in this machine.
Skin irritation may occur if other
garments are contaminated with
the glass fibres.
!Items that have been soiled
with substances such as cooking
oil, acetone, alcohol, petrol,
kerosene, spot removers,
turpentine, waxes and wax
removers should be washed in
hot water with an extra amount
of detergent before being dried
in the tumble dryer.
! Remove all objects from pockets
such as lighters and matches.
!Lighters and matches must not
be left in pockets and NEVER
use flammable liquids near the
machine.
!Maximum load drying weight:
see energy label.
! To consult the product technical
specification please refer to the
manufacturer website.
The Laundry
WARNING
Foam rubber materials can ,
under certain circumstances,
when heated become ignited
by spontaneous combustion.
Items such as foam rubber
(latex foam), shower caps,
waterproof textiles, rubber
backed articles and clothes
or pillows fitted with foam
rubber pads MUST NOT be
dried in the tumble dryer.
WARNING
Do not tumble dry fabrics
treated with dry cleaning
fluids.

!
8
WARNING
Fire hazard / Flammable
materials.
!The appliance contains R290,
an eco-sustainable refrigerating
gas that is flammable. Keep
open flames and sources of
ignition away from the appliance.
!Check there is no visible
damage on the appliance. Do
not use the appliance if it is
damaged.
!Should there be any kind of
problem, please contact your
specialised retailer or one of
our customer support centres.
WARNING
Ensure that the openings on
the appliance and the openings
of the compartment the appliance
is fitted in (for built-in models)
are clear of obstructions.
WARNING
Do not damage the refrigerating
circuit.
!Any repairs or interventions on
the appliance must be carried
out only by an authorised
assistance service.
!Disposing of the device
incorrectly could cause fires or
poisoning.
!Dispose of the device correctly
and do not damage the pipes
used for the circulation of the
refrigerating fluid.

!
EN
9
2. DRAIN HOSE KIT
In order to avoid to empty the water
container after each drying cycle, the water
can be discharged directly to a waste water
drain pipe. Water Bye-Laws prohibit
connection to a surface water drain. The
waste water drain pipe should be located
adjacent to the tumble dryer.
The kit consists of: 1 hose and 1 bung.
1. The water drainage system is located at
the back of the machine on the lower
right side (figure 2).
2. Disconnect the hose (A) from the fitting
(B) by pulling it upwards (figure 3).
3. Close the extracted tube with the cap
(C) supplied with the kit (figure 4).
4. Connect the hose into the fitting (B)
making sure it is inserted securely
(figures 5-6).
B
A
C
1
2
3
4
5
6
WARNING
Switch off and remove the tumble
dryer plug from the electricity supply
before carrying out any work.
The hose must be connected to a
drain system with a maximum height
of 85 cm compared to the base of the
dryer (figure 1).
Fitting the drain hose
Once the machine is in place, check to
ensure that the new hose does not
kink when pushing the tumble dryer
into position.

!
10
3. WATER CONTAINERS
The water removed from the laundry during
the drying cycle is collected in a container.
When the container is full, an indicator light,
or on some models a message on the
display, will advise you that it MUST be
emptied (however, we recommend to empty
it after each drying cycle).
1. Gently pull out the water container
holding the handle (A).
When it is full the water container will
weigh about 6 kg.
2. Tilt the water container to empty the
water out through the spout (B).
When empty, replace the water container
back as shown; (C) first insert the base of
the container into position as shown (1)
then gentle push the top into position (2).
3. Press the programme start button to
restart the cycle.
AB
1C
*Depending on model
1. Gently pull the bottom of the kickplate so
that it unclips from the dryer. The top
section can then be unhinged allowing
the kickplate to be completely removed (A).
2. Pull firmly on the handgrip and slide the
water container out of the dryer (B).
Support the container with both hands
(C). When full, the water container will
weigh about 4 kg.
3. Open the lid located on the top of the
container and empty the water (D).
4. Refit the lid and slide the water container
back into position (D). PUSH FIRMLY
INTO PLACE.
5. Refit the kickplate by engaging the
hinges at the top and 'snapping' the lower
clips into place.
AB
CD
*Depending on model
Very little water will collect during the
first few cycles of a new machine as an
internal reservoir is filled first.
To remove the container tank in
door drawer *
ONLY FOR MODELS WITH DRAIN
HOSE KIT
If you have the option of drainage
near to the dryer you can use the
discharge kit to provide a permanent
drainage for the water collected in the
container of the dryer. This means
that you don't have to empty the water
container.
To remove the container bottom
water drawer *

!
EN
11
4. DOOR, FILTERS AND
HEAT EXCHANGER
!Pull on handle to open the door.
!To restart the appliance, close the door
and press the programme start button.
Lint filters and heat exchanger cleaning
indicator light
The indicator light illuminates in fixed mode to
signal the need of cleaning the lint filters and in
blinking mode to signal the need of cleaning
the heat exchanger.
If the laundry is not drying check that the
filters are not clogged.
Door
WARNING
When the tumble dryer is in use the
drum and door may be VERY HOT.
WARNING
(For models with water collection tray)
If you open the door mid cycle, before
the cool-down cycle has completed,
the handle may be hot. Please use
extreme caution when attempting to
empty the water reservoir during the
cycle.
Filters and heat exchanger
Clogged filters and heat exchanger
could increase the drying time and
cause damages and expensive
cleaning operation.
In order to have the maximum
effectiveness of the machine,
checking the cleanliness of all filters
before each drying cycle is essential.
WARNING
Do not use the tumble dryer without
the filters.
.
.
If you clean filters under water, remember
to dry them.
WARNING
Clean the filters before every cycle.

!
12
1. Extract the two filters Aand Bin
sequence pulling them upwards, as
shown in the figure.
AB
2. Open the filters.
AB
3. Gently remove lints from both filters using
your fingertips or a soft brush, a cloth or
under water running.
AB
AB
AB
AB
4. Close both filters by repositioning them
inside the door, making sure they are
positioned correctly in place.
AB
B A
To clean the lint filters
WARNING
Before reinserting the filters, make
sure there is no lint residue inside the
compartment; if not, remove it with a
vacuum cleaner.

!
EN
13
1. Remove the kickplate.
2. Turn the handle anti-clockwise and pull
out the front cover.
3. Gently clean the heat exchanger using a
soft brush or a vacuum cleaner, to
remove any dust or fluff, paying attention
to not damage the fins.
4. Refit the front cover ensuring it is in the
right position. Turn the handle clockwise
to lock the front cover.
5. Refit the kickplate.
To clean the heat exchanger
WARNING
Clean the exchanger every six months
or when the filters cleaning indicator
light blinks.
WARNING
Do not touch the fins with hands in
order to avoid injury.
Be careful when cleaning in order not
to damage the heat exchanger.

!
14
5. PRACTICAL HINTS
Before using the tumble dryer for the first
time:
!Please read this instruction book
thoroughly.
!Remove all items packed inside drum.
!Wipe the inside of the drum and door with
a damp cloth to remove any dust which
may have settled in transit.
Make sure that the laundry you are going to
dry is suitable for drying in a tumble dryer,
as shown by the care symbols on each
item. Check that all fastenings are closed
and that pockets are empty. Turn the
articles inside out. Place clothes loosely in
the drum to make sure that they don't get
tangled.
Silk, nylon stockings, delicate embroidery,
fabrics with metallic decorations, garments
with PVC or leather trimmings.
Only put into the tumble dryer laundry which
has been thoroughly wrung or spin-dried.
The drier the laundry the shorter the drying
time thus saving electricity.
ALWAYS
!Check that the filters are clean before
every drying cycle.
NEVER
!Put dripping wet items into the tumble
dryer, this may damage the appliance.
!By care symbols
These can be found on the collar or inside
seam:
Suitable for tumble drying.
Tumble drying at high temperature.
Tumble drying at low temperature
only.
Do not tumble dry.
If the item does not have a care label it
must be assumed that it is not suitable for
tumble drying.
!By amount and thickness
Whenever the load is bigger than the dryer
capacity, separate clothes according to
thickness (e.g. towels from thin underwear).
!By type of fabric
Cottons/linen: Towels, cotton jersey, bed
and table linen.
Synthetics: Blouses, shirts, overalls, etc.
made of polyester or polyamid, as well as
for cotton/synthetic mixes.
Clothes preparation
Do not tumble dry
WARNING
Do not dry articles which have been
treated with a dry cleaning fluid or
rubber clothes (danger of fire or
explosion).
During the last 15 minutes the load is
always tumbled in cool air.
Energy saving
Sort the load as follows
WARNING
Do not overload the drum, large items
when wet exceed the maximum
admissible clothes load (for example:
sleeping bags, duvets).

!
EN
15
!Clean the filters after every drying cycle.
!In models equipped with a water
collection tray, the tray should be emptied
after every drying cycle.
!Wipe the outside of the machine and the
door with a soft cloth.
!DO NOT use abrasive pads or cleaning
agents.
!To prevent the door sticking or the
buildup of fluff clean the inner door and
gasket with a damp cloth after every drying
cycle.
Cleaning the dryer
WARNING
The drum, door and load may be very
hot.
WARNING
Always switch off and remove the plug
from the electricity supply before
cleaning this appliance.
WARNING
For electrical data refer to the rating
label on the front of the dryer cabinet
(with the door open).

!
16
6. QUICK USER GUIDE
1. Open the door and load the drum with
laundry. Ensure that garments do not
hinder closure of the door.
2. Gently close the door pushing it slowly
until you hear the door 'click' shut.
3. Select the desired drying programme by
turning the programme knob or, in some
models, by pressing the specific button
(check the programme table for specific
details).
4. Press the programme start button. The
dryer will start automatically.
5. If the door is opened during the
programme to check the laundry, it is
necessary to press programme start
to recommence drying after the door
has been closed.
6. When the cycle is nearing completion
the machine will enter the cool down
phase, the clothes will be tumbled in
cool air allowing the load to cool down.
7. Following the completion of the cycle
the drum will rotate intermittently to
minimize creasing. This will continue
until the machine is switched OFF or the
door is opened.
Power input / Power current fuse amp/
Supply voltage: see rating plate.
Maximum load: see energy label.
Energy class: see energy label.
7. CONTROLS AND
PROGRAMMES
A
N
CEDB
I G FHL
M
A
PROGRAMME SELECTOR with
OFF position
B
START/PAUSE button
C
DELAY START button
D
TIME CYCLE SELECTION button
E
DRYING SELECTION button
F
START PAUSE indicator light
G
TIME CYCLE SELECTION
indicator lights
H
DRYING SELECTION indicator
lights
I
DELAY START TIME / DRYING
STAGE indicator lights
L
WATER CONTAINER indicator light
M
LINT FILTERS AND HEAT
EXCHANGER CLEANING
indicator light
N
SMART TOUCH area
Do not open the door during the
automatic programmes in order to
obtain a proper drying.
Technical data

!
EN
17
!Rotating the programme selector in both
directions it's possible to select the
desired drying programme.
!To cancel the selections or switch off the
appliance rotate the programme selector
on OFF (remember to unplug the
appliance).
!Press the START/PAUSE button to start
the programme set with the programme
knob (the corresponding indicator light
will light up).
!Moreover, if you want to modify the
chosen programme, press the desired
options buttons and then press START/
PAUSE button to start the cycle.
!After switching on the appliance, wait a
few seconds for the programme to start
running.
PROGRAMME DURATION
!When a programme is selected the
appliance calculates the time to the end
of the selected programme based upon a
standard loading but, during the cycle, the
appliance corrects the time to the
humidity level of the load.
PROGRAMME END
!The "END" indicator light will light up at
the end of the programme, it is now
possible to open the door.
!At the end of the cycle, turn off the
appliance by turning the programme
selector to the OFF position.
PAUSING THE MACHINE
!Press the START/PAUSE button (the
corresponding indicator light will flash,
showing that the machine is paused).
!Press the START/PAUSE button again to
re-start the programme from the point it
had been paused at.
CANCELLING THE SET PROGRAMME
!To cancel the programme, turn the
programme selector to the OFF position.
If there is a break in the power supply
whilst the machine is operating, when
the power is restored, by pressing the
START/PAUSE button, the machine will
restart from the beginning of the phase it
was in when the power was lost.
!Appliance start time can be set with this
button, delaying the start by 3, 6or 9
hours.
WARNING
Don’t touch the buttons while inserting
the plug because the machines
calibrates the systems during the first
seconds: touching the buttons, the
machine couldn’t work property. In
this case, remove the plug and repeat
the operation.
PROGRAMME SELECTOR with
OFF position
START/PAUSE button
Close the porthole BEFORE pressing
the START/PAUSE button.
Only the options compatible with the
set programme can be selected.
The programme selector must
ALWAYS be put in the OFF position at
the end of the drying cycle before a
new one can be selected.
DELAY START button

!
18
!Proceed as follows to set a delayed start:
- Select a programme.
- Press the DELAY START button (each
time the button is pressed the start will
be delayed by 3, 6 or 9hours
respectively and the corresponding time
indicator light will light up).
- Press START/PAUSE button to
commence the delay start operation
(the indicator light associated with the
selected delay start time will blink). At
the end of the required time delay the
programme will start.
!It is possible to cancel the DELAY
START by turning the programme
selector to OFF.
!To set a timed drying, press this button
until the corresponding indicator light to
the desired duration will light on.
!It's possible transform a cycle from
automatic to timed, up to 3 minutes after
the start of the cycle.
!After this selection to reset the automatic
drying functioning is necessary to switch
off the dryer.
!In case of incompatibility, all indicator
lights flash quickly for 3 times.
!This button allows to set the desired
dryness level editable option up to 3
minutes after the starting of the cycle:
Ready to Iron: it leaves the garments
slightly wet to facilitate ironing.
Dry Hanger: to get garment ready to
be hang.
Dry wardrobe: for laundry that can be
directly stored.
Extra-dry: to get completely dry
garments, ideal for full load.
!This appliances is equipped with Drying
Manager function. On automatic cycles,
each level of intermediate drying, prior to
the reaching the selected one, is indicated
by flashing the light indicator corresponding
to the degree of drying reached.
In case of incompatibility, all indicator
lights flash quickly for 3 times.
It lights up when the START/PAUSE button
has been pressed.
The indicator lights are illuminated to show
the duration selected by the relevant button.
The indicator lights display the degrees
of dryness that can be selected by the
relevant button.
!Each time the DELAY START button is
pressed the indicator lights show how
many hours of delay you chosen (3, 6 or
9hours) and the countdown until the end
of it.
START PAUSE indicator light
TIME CYCLE SELECTION indicator
lights
DRYING SELECTION indicator
lights
DELAY START TIME / DRYING
STAGE indicator lights
Opening of the porthole with delayed
start set, after re-closing the porthole,
press START/PAUSE again to resume
the counting.
TIME CYCLE SELECTION button
DRYING SELECTION button

!
EN
19
!When a programme is running, the
indicator lights will light in sequence to
indicate the current phase:
DRYING CYCLE
It lights up when the drying cycle is
running.
COOLING
It lights up when the cycle is in the
cooling phase.
END CYCLE
It lights up when the cycle is done.
It lights up when it’s necessary to empty the
condensate water tank.
The indicator light illuminates in fixed mode
to signal the need of cleaning the lint filters
and in blinking mode to signal the need of
cleaning the heat exchanger.
WATER CONTAINER indicator
light
LINT FILTERS AND HEAT
EXCHANGER CLEANING indicator
light

!
20
This appliance is equipped with Smart
Touch technology that allows you to
interact, via the App, with smartphones
based on Android operating system and
equipped with compatible NFC (Near Field
Communication) function.
!Download on your smartphone the
Candy simply-Fi App.
HOW TO USE SMART TOUCH
FIRST TIME - Machine registration
!Enter the "Settings" menu of your
Android smartphone and activate the
NFC function inside the "Wireless &
Networks" menu.
!Turn the knob to the Smart Touch
position to enable the sensor on the
dashboard.
!Open the App, create the user profile and
register the appliance following the
instructions on the phone display or the
"Quick Guide" attached on the machine.
NEXT TIME – Regular usage
!Every time you want to manage the
machine through the App, first you have
to enable the Smart Touch mode by
turning the knob to the Smart Touch
indicator.
!Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; following the
steps mentioned earlier.
!If you want to start a cycle, load the
laundry and close the door.
!Select the desired function in the App
(e.g.: starting a programme).
!Follow the instructions on the phone
display, KEEPING IT ON the Smart
Touch logo on the machine dashboard,
when requested to do so by the App.
SMART TOUCH
The Candy simply-Fi App is available
for devices running both Android and
iOS, both for tablets and for
smartphones. However, you can
interact with the machine and take
advantage of the potential offered
by Smart Touch only with Android
smartphones equipped with NFC
technology, according to following
functional scheme:
Android smartphone
with compatible NFC
technology
Interaction with the
machine + contents
Android smartphone
without NFC technology
Contents only
Android Tablet
Contents only
Apple iPhone
Contents only
Apple iPad
Contents only
Get all the details of the Smart Touch
functions, browsing the App in DEMO
mode.
Depending on the smartphone model
and its Android OS version, the
process of the NFC activation may be
different. Refer to the smartphone
manual for more details.