Capture advance R2-HD2MPEYE User manual

Camera OSD Operation Guide
For R2-HD2MPEYE R2-HD2MPBUL
ISSUE V1.0
DATE
2022-03-01

Operation Guide
Contents
Issue V1.0 (2019-03-29)
ii
About This Document
Purpose
This document describes how to use the web management system for DVR and the cameras managed
by DVR.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal
injury.
Calls attention to important information, best practices and
tips.
NOTE is used to address information not related to personal
injury, equipment damage, and environment deterioration.

Operation Guide
Contents
Issue V1.0 (2019-03-29)
iii
Contents
About This Document.................................................................................................................... ii
1 OSD Main Menu...........................................................................................................................1
1.1 Procedure......................................................................................................................................................................1
1.1.1 Camera Control Using Five Buttons..........................................................................................................................1
1.2 OSD Main Menu Interface ...........................................................................................................................................1
2 OSD Setting ...................................................................................................................................3
2.1 AE.................................................................................................................................................................................3
2.2 AWB .............................................................................................................................................................................4
2.3 DAY NIGHT.................................................................................................................................................................5
2.4 IMAGE ENHANCE.....................................................................................................................................................6
2.5 VIDEO SETTING........................................................................................................................................................8
2.6 LANGUAGE................................................................................................................................................................8
2.7 FUNC ...........................................................................................................................................................................9
2.8 RESET........................................................................................................................................................................11
2.9 SAVE-EXIT................................................................................................................................................................11
2.10 EXIT.........................................................................................................................................................................12

Operation Guide
Issue V1.0 (2019-03-29)
1
1 OSD Main Menu
1.1 Procedure
1.1.1 Camera Control Using Five Buttons
If your camera has four arrow buttons and one SET button, you can use the buttons to operate the OSD
main menu. Figure 1-1 shows the five buttons.
Figure 1-1 Five-button layout
The buttons have the following functions:
SET: Press this button to open the OSD main menu or end setup.
UP/DOWN: Press the two buttons to select the upper or lower menu.
LEFT/RIGHT: Press the two buttons to select different modes.
----End
1.2 OSD Main Menu Interface
The OSD main menu interface includesAE, AWB, DAY / NIGHT, IMAGE ENHANCE, VIDEO
SETTING, LANGUAGE, FUNC, RESET,SAVE & EXIT, and EXIT as shown in Figure 1-2.

Operation Guide
Issue V1.0 (2019-03-29)
2
Figure 1-2 OSD main menu interface
----End

Operation Guide
Issue V1.0 (2019-03-29)
3
2 OSD Setting
2.1 AE
AE is intended to adjust image brightness by setting parameters such as aperture, shutter, and gain. The
EXPOSURE interface includes BRIGHTNESS, EXPOSURE MODE.
Procedure
Step 1 Press the UP or DOWN button to select AE.
Step 2 Press the SET button to open the EXPOSURE interface, as shown in Figure 2-1.
Figure 2-1 EXPOSURE interface
Step 3 Press the UP or DOWN button to select BRIGHTNESS and press the LEFT or RIGHT
button to select a brightness value. The default brightness is 16 and the setting range is 0-100.

Operation Guide
Issue V1.0 (2019-03-29)
4
Step 4 Press the UP or DOWN button to select EXPOSURE MODE and press the LEFT or
RIGHT button to select a exposure mode.
The exposure mode includes GLOBE, and BLC.
−BLC: Press the LEFT or RIGHT button to select BLC, press the LEFT or RIGHT
button to adjust BLC value. The default BLC is 4 and the setting range is 0-7.
−GLOBE: Press the LEFT or RIGHT button to select BLC.
Step 5 Press the UP or DOWN button to select RETURN and press the SET return to the OSD
main menu interface.
----End
2.2 AWB
White balance is intended to reproduce the actual colors of the observed scene when the illuminance
and color temperature of the target object are changed. You can set WB to GRAY WORLD, MWB or
PRO.
Procedure
Step 1 Press the UP or DOWN button to select AWB. Press the SET button to open the WB
interface, as shown in Figure 2-2.
Figure 2-2 AWB interface
Step 2 Press the LEFT or RIGHT button to set the MODE.The options are GARY WORLD,
MWB and PRO. The default mode is GRAY WORLD
When MWB mode is selected, you can set white balance parameters, as shown in Figure 2-3.

Operation Guide
Issue V1.0 (2019-03-29)
5
Figure 2-3 MWB interface
1. Press the UP or DOWN button to select RGAIN, and press the LEFT or RIGHT button
to set RGAIN. The default RGAIN is 40 and the setting range is 0-127.
2. Press the UP or DOWN button to select BGAIN, and press the LEFT or RIGHT button
to set BGAIN. The default BGAIN is 30 and the setting range is 0-127.
Step 3 Press the UP or DOWN button to select RETURN, and press the SET button to return to the
OSD main menu interface.
----End
2.3 DAY NIGHT
You can set Day-Night to MONO, COLOR,AUTO, or EXT.
Procedure
Step 1 Press the UP or DOWN button to select Day-Night. Press the SET button to open the Day
/Night interface, as shown in Figure 2-4.

Operation Guide
Issue V1.0 (2019-03-29)
6
Figure 2-4 DAY/NIGHT interface
Step 2 Press the LEFT or RIGHT button to set the Mode.
Step 3 Press the UP or DOWN button to select SMART IR to close or open.
Step 4 Press the UP or DOWN button to select RETURN and press the SET return to the OSD
main menu interface.
----End
2.4 IMAGE ENHANCE
The Image Enhance interface includes CONTRAST, SHARPNESS, SATURATE, 3DNR and
DWDR, as shown in Figure 2-5.

Operation Guide
Issue V1.0 (2019-03-29)
7
Figure 2-5 Image enhance
Procedure
Step 1 Press the UP or DOWN button to select IMAGE ENHANCE. Press the SET button to open
the IMAGE ENHANCE interface.
Step 2 Press the UP or DOWN button to select CONTRAST. Press the LEFT or RIGHT button to
choose manual or auto , manual mode need press DOWN button to go next one, press the
LEFT or RIGHT button set the CONTRAST value. The default contrast is 5 and the setting
range is 0-10.
Step 3 Press the UP or DOWN button to select SHARPNESS. Press the LEFT or RIGHT button to
choose manual or auto , manual mode need press DOWN button to go next one, press the
LEFT or RIGHT button set the SHARPNESS value. The default sharpness is 10 and the
setting range is 0-10.
Step 4 Press the UP or DOWN button to select SATURATE. Press the LEFT or RIGHT button to
choose manual or auto , manual mode need press DOWN button to go next one, press the
LEFT or RIGHT button set the SATURATE value. The default color gain is 5 and the
setting range is 0-10.
Step 5 Press the UP or DOWN button to select 3DNR. Press the LEFT or RIGHT button to choose
manual or auto , manual mode need press DOWN button to go next one, press the LEFT or
RIGHT button set the 3DNR value. The default DNR is 0 and the setting range is 0-10.
Step 6 Press the UP or DOWN button to select DWDR. Press the LEFT or RIGHT button to
choose CLOSE or OPEN.
Step 7 Press the UP or DOWN button to select RETURN and press the SET return to the OSD
main menu interface.