Capture R2-HD5MPDME User manual

Camera OSD Operation Guide
For R2-HD5MPDME
ISSUE V1.0
DATE
2022-03-01

Operation Guide
Contents
Issue V1.0 (2022-03-03)
ii
About This Document
Purpose
This document describes how to use the web management system for DVR and the cameras managed
by DVR.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal
injury.
Calls attention to important information, best practices and
tips.
NOTE is used to address information not related to personal
injury, equipment damage, and environment deterioration.

Operation Guide
Contents
Issue V1.0 (2022-03-03)
iii
Contents
About This Document.................................................................................................................... ii
Purpose...............................................................................................................................................................................ii
Symbol Conventions...........................................................................................................................................................ii
Contents ........................................................................................................................................... iii
1 OSD Main Menu........................................................................................................................... 1
1.1 Procedure......................................................................................................................................................................1
1.1.1 Camera Control Using Joystick................................................................................................................................. 1
1.2 OSD Main Menu Interface ...........................................................................................................................................1
2 OSD Setting ................................................................................................................................... 3
2.1 AE................................................................................................................................................................................. 3
2.2 AWB............................................................................................................................................................................. 4
2.3 DAY / NIGHT .............................................................................................................................................................. 6
2.4 IMAGE ENHANCE..................................................................................................................................................... 7
2.5 VIDEO SETTING........................................................................................................................................................ 9
2.6 LANGUAGE.............................................................................................................................................................. 10
2.7 RESET........................................................................................................................................................................ 10
2.8 SAVE&EXIT.............................................................................................................................................................. 10
2.9 EXIT........................................................................................................................................................................... 10

Operation Guide
Issue V1.0 (2022-03-03)
1
1 OSD Main Menu
1.1 Procedure
1.1.1 Camera Control Using Joystick
If your camera has four arrow buttons and one SET button, you can use the buttons to operate the OSD
main menu. Figure 1-1 shows the joystick.
Figure 1-1 Joystick layout
The buttons have the following functions:
SET: Press this button to open the OSD main menu or end setup.
UP/DOWN: Press the two buttons to select the upper or lower menu.
LEFT/RIGHT: Press the two buttons to select different modes.
----End
1.2 OSD Main Menu Interface
The OSD main menu interface includesAE, AWB, DAY/ NIGHT, VIDEO SETTING, LANGUAGE,
RESET, SAVE & EXIT, and EXIT, as shown in Figure 1-2.

Operation Guide
Issue V1.0 (2022-03-03)
2
Figure 1-2 OSD main menu interface
----End

Operation Guide
Issue V1.0 (2022-03-03)
3
2 OSD Setting
2.1 AE
AE is intended to adjust image brightness by setting parameters such as aperture, shutter, and gain. The
EXPOSURE interface includes BRIGHTNESS, EXPOSURE MODE.
Procedure
Step 1 Press the UP or DOWN button to select AE.
Step 2 Press the SET button to open the EXPOSURE interface, as shown in Figure 2-1.
Figure 2-1 EXPOSURE interface

Operation Guide
Issue V1.0 (2022-03-03)
4
Step 3 Press the UP or DOWN button to select BRIGHTNESS and press the LEFT or RIGHT
button to select a brightness value. The default brightness is 6 and the setting range is 0-100.
Step 4 Press the UP or DOWN button to select EXPOSURE MODE and press the LEFT or
RIGHT button to select a exposure mode.
The exposure mode includes GLOBE, CENTER, and BLC.
−BLC: Press the LEFT or RIGHT button to select BLC, press the LEFT or RIGHT
button to adjust BLC value. The default BLC is 1 and the setting range is 1-9.
−GLOBE: Press the LEFT or RIGHT button to select BLC.
Step 5 Press the UP or DOWN button to select RETURN and press the SET return to the OSD
main menu interface.
----End
2.2 AWB
White balance is intended to reproduce the actual colors of the observed scene when the illuminance
and color temperature of the target object are changed. You can set WB to GRAY WORLD, MWB or
PRO.
Procedure
Step 1 Press the UP or DOWN button to select AWB. Press the SET button to open the WB
interface, as shown in Figure 2-2.

Operation Guide
Issue V1.0 (2022-03-03)
5
Figure 2-2 AWB interface
Step 2 Press the LEFT or RIGHT button to set the MODE.The options are ATW and MWB. The
default mode is MWB
When MWB mode is selected, you can set white balance parameters, as shown in Figure 2-3.

Operation Guide
Issue V1.0 (2022-03-03)
6
Figure 2-3 MWB interface
1. Press the UP or DOWN button to select RGAIN, and press the LEFT or RIGHT button
to set RGAIN. The default RGAIN is 50 and the setting range is 0-100.
2. Press the UP or DOWN button to select BGAIN, and press the LEFT or RIGHT button
to set BGAIN. The default BGAIN is 50 and the setting range is 0-100.
Step 3 Press the UP or DOWN button to select RETURN, and press the SET button to return to the
OSD main menu interface.
----End
2.3 DAY / NIGHT
You can set Day / Night to B / W, COLOR,AUTO, or EXT.
Procedure
Step 1 Press the UP or DOWN button to select Day-Night. Press the SET button to open the Day /
Night interface, as shown in Figure 2-4.

Operation Guide
Issue V1.0 (2022-03-03)
7
Figure 2-4 DAY/NIGHT interface
Step 2 Press the LEFT or RIGHT button to set the Mode.
Step 3 Press the UP or DOWN button to select RETURN and press the SET return to the OSD
main menu interface.
----End
2.4 IMAGE ENHANCE
The Image Enhance interface includes CONTRAST, SHARPNESS, SATURATE, 2 DNR, D-WDR
FLIP, MIRROR and, as shown in Figure 2-5.