Car Keys Express GMRM-4TZ1RE User manual

V2.0221
USER GUIDE
Pairing Instructions for Chevrolet, Buick, GMC, Cadillac,
Oldsmobile, Pontiac, Saturn, Suzuki Replacement Remotes.
Instruction Manual Part Number: GMPRR-7022-0
REPLACEMENT
REMOTE
Replacing car keys is simple and affordable again.™
www.CarKeysExpress.com

USER GUIDE
2
IMPORTANT NOTES
►You MUST have your existing key that already works with your vehicle
in order to use the EZ Installer™. If you have no working keys, return the
entire product to the retailer where it was purchased.
►All existing, working remotes must be present during the pairing
process. Once you pair a new remote, all previous remotes will be
erased from the memory. The others will not be functional until you pair
them again.
►Vehicle battery should be in good condition and fully charged prior
to pairing the new remote. Turn off headlights, radio, A/C fan, etc. to
minimize battery draw during the process.
►Do not use the EZ Installer while the vehicle is in motion. Unplug it
from the OBD port before driving the vehicle.
►Only original remote features will work, regardless of buttons included
in this package. This remote does not add features your vehicle did not
have before.
►For your security, a tamper-evident security label is installed over the
EZ Installer connector. If this label is missing, damaged, or the word
"VOID" appears on the EZ Installer, please exchange this product for a
new one at the retailer where it was purchased.
►Before pairing, familiarize yourself with the remote’s compatibility with
the make, model, and year of your vehicle on page 3.
LET’S GET STARTED
This product requires PAIRING. It’s important to follow these steps in
order to successfully complete setup.
If you skip a step, the remote WILL NOT work properly, and you’ll have
to repeat the setup process.
Find your PRIMARY DIAL POSITION in the following chart by
referencing your vehicle’s make, model, and year.

USER GUIDE
3
MAKE/MODEL
BUICK
SATURN
PONTIAC
CHEVROLET
YEARS PRIMARY
DIAL POSITION ALTERNATE DIAL POSITION
Allure 2005-2006 4
2007-2009 6
LaCrosse 2005-2006 4 6
2007-2009 6 4
Aura 2007-2009 1 8
Outlook 2007-2010 1 8
Sky 2007-2010 1 8
G5 2007-2009 18
G6 2005-2006 3
2007-2010 1 8
Grand Prix 2005-2006 4 6
2007-2008 6 4
Solstice 2006-2009 1 8
Cobalt 2007-2010 1 8
Malibu 2004-2006 3
2007-2012 1 8
Malibu MAXX 2004-2006 3
2007 1 8
COMPATIBILITY LOOKUP
Visit CKESimpleKey.com for the most up-to-date vehicle compatibility list.

USER GUIDE
4
REMOTE PAIRING INSTRUCTIONS
Instructions have timing requirements. If you wait too long between steps, your
vehicle’s computer may time out, requiring you to start over. Once you begin
the pairing procedure, move at a quick and even pace.
NOTE: If the EZ Installer is left in the vehicle’s on-board diagnostic (OBD) port
for more than 5 minutes, an alarm will sound reminding you to remove it.
NOTE: If at any point the EZ Installer continues to beep rapidly, please refer to
the FAQ section for more information.
NOTE: If Primary Dial Position is 1, this process will add your new remote to
the vehicle. Your vehicle has a memory that can only hold 4 remotes. If the EZ
Installer beeps rapidly, you have too many remotes paired to the vehicle.
Turn the dial to Secondary Dial Position 8. This process is going to erase the
memory. You MUST have all remotes you want to program to your vehicle. You
can program remotes using the EZ Installer at any time, but all current remotes
will be erased when going through this process.
If Primary Dial Position is 2-7, this procedure will erase all old remotes when
starting the programming procedure. You MUST have all existing remotes
present during the programming process. Remotes can be added at any time
using the EZ Installer, but each time it is used the remote memory will be
erased. You may add up to 4 total remotes during this procedu
1. Find your vehicle’s make, model, and year in the COMPATIBILITY LOOKUP
on page 3. Turn the dial on the EZ Installer to the position listed for your
vehicle’s make, model, and year.
NOTE: If more than 1 dial position exists for your vehicle, try the PRIMARY
dial position first. If you’re unable to successfully pair the remote, try the
ALTERNATE dial position listed for your vehicle.
NOTE: One working key should be present during the pairing process.
2. Begin with the vehicle in PARK and the engine OFF.
3. Enter the vehicle and close all doors.

USER GUIDE
5
4. Insert the key into the ignition and turn the key to the ON position. This
should be the position before starting the vehicle, see below. DO NOT start
the vehicle
5. Remove the security label from the EZ Installer and insert it firmly into
the on-board diagnostic (OBD) port located under the dash.
a. The location of your vehicle’s OBD port can be found in the
owner’s manual.
6. The EZ Installer will beep twice when it powers up and starts the process.
7. The EZ Installer will sound a short tune when programming mode has
started.
a. Your vehicle may or may not provide feedback such as the door
lock cycling, a message on the dashboard, or a chime.
8. After hearing this short tune, press and hold both Lock and Unlock on your
new remote for approximately 15 seconds.
9. Repeat step 8 for each additional remote to be programmed.
10. After all remotes have been added, turn the key to the Off position and
unplug the EZ Installer.
11. Press buttons on each remote to test they were properly programmed to
the vehicle.*
*Some vehicles may need to have the engine started and stopped, and the
driver's door opened and closed before the remotes will work.
FREQUENTLY ASKED QUESTIONS
Q: Can I use the same EZ Installer on other vehicles?
A: No. The EZ Installer will be locked to the first vehicle it is used on. You may
add more remotes to the same vehicle again as needed, but it will not work on
different vehicles. If the EZ Installer sounds 3 beeps at 1 second intervals, and
then beeps rapidly, this signifies the device has already been used on another
vehicle. Visit CKESimpleKey.com or your local retailer to purchase additional
remotes.
GM IGNITION POSITIONS

USER GUIDE
6
Q: The new remote won’t pair to my car. What should I do?
A: If the EZ Installer doesn’t pair the remote to your car, most likely, an incorrect
dial position was used. In this case, the EZ Installer will beep continuously
after you press the pairing button. Check the compatibility section on page
3 to confirm the correct dial position for your make, model, year, and button
configuration of your original remote. Remove the EZ Installer, turn the Ignition
off and try the pairing process from step 1. If the remote still won’t pair, please
contact customer service at [phone].
Q: The EZ Installer was unplugged during the pairing process. What should I do?
A: The EZ Installer must remain plugged into the on-board diagnostic (OBD)
port until pairing is complete. If the EZ Installer becomes unplugged during the
pairing process, turn the ignition to the OFF position, remove the key, and begin
the pairing process again.
FCC REGULATORY STATEMENTS
FCC ID: 2AOKM-GV1
47 CFR §15.19(a)(3) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2)
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
NOTE: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
HELP
For help or assistance, please contact technical support at [phone].
OTHER KEYS
Visit CarKeysExpress.com/store to find a variety of award-winning products, like
Universal Car Keys, Universal Car Remotes, and OEM keys and remotes.

USER GUIDE
7
PAGE INTENTIONALLY LEFT BLANK.

Patent US10755506B2
Designed and assembled in the USA
12101 Sycamore Station Place Ste. 140
Louisville, KY 40299
[phone]
© 2021 Car Keys Express
Replacing car keys is simple and affordable again.™

V2.0221
MANUAL DE USUARIO
Instrucciones de emparejamiento para Chevrolet, Buick, GMC,
Cadillac, Oldsmobile, Pontiac, Saturn, Suzuki Remplazo Remotos.
Número de la parte del manual de instrucciones: GMPRR-7022-0
REMPLAZO DEL CONTROL
REMOTO
Replacing car keys is simple and affordable again.™
www.CarKeysExpress.com

MANUAL DE USUARIO
2
NOTAS IMPORTANTES
►Usted DEBE tener la llave que funciona con su vehículo para poder
usar el instalador EZ Installer™. Si no tiene llaves que funcionen,
devuelva todo el producto donde lo compró.
►Durante el proceso de sincronización deben estar presentes todos
los controles remotos que funcionan. Una vez que sincronice un
control remoto nuevo, se borrarán de la memoria los controles remotos
antiguos. Los demás no funcionarán hasta que los sincronice de nuevo.
►Para sincronizar el control nuevo, la batería del vehículo debe estar en
buen estado y completamente cargada. Apague las luces delanteras,
la radio, el aire acondicionado, etc., para minimizar el consumo de la
batería durante el proceso.
►No utilice el instalador EZ Installer mientras el vehículo está en
movimiento. Desconéctelo del puerto de diagnóstico a bordo (OBD)
antes de conducir el vehículo.
►Solo funcionarán las funciones del control original,
independientemente de los botones incluidos en este paquete. Este
control no añade funciones que su vehículo no tenga.
►Para su seguridad, se instala una etiqueta de seguridad a prueba de
manipulaciones del conector EZ Installer. Si la etiqueta no está o está
dañada, o si la palabra VOID aparece en el conector EZ Installer, cambie
el producto por uno nuevo en la tienda donde lo compró.
►Antes de sincronizarlo, familiarícese con la compatibilidad del control
con la marca, el modelo y el año de su vehículo en la página 3.
COMENCEMOS
Este producto requiere una SINCRONIZACIÓN. Es importante seguir
estos pasos para completar la configuración de manera correcta.
Si omite un paso, el control NO funcionará correctamente, y tendrá que
repetir el proceso de configuración.
Encuentre la POSICIÓN PRIMARIA DE LA PERILLA en la siguiente tabla
según la marca, el modelo, el año.