Carefree BT12 User manual

O WNER ' S M ANUAL
F REESTYLE RM A WNING
12V
M OTORIZED R OOF M OUNTED B OX A WNING
RV
with Carefree’s BT12 Wireless Awning Control System
Using Bluetooth®wireless technology
Table of Contents
Introduction ........................................................................................................... 2 
Operation ............................................................................................................... 6 
Standard Switch Operation............................................................................ 6 
Ignition Lockout ............................................................................................. 6 
BT Motion Sensor.......................................................................................... 7 
Options................................................................................................................... 9 
BT Remote .................................................................................................... 9 
LED’s........................................................................................................... 10 
Setting the System into Pairing Mode ......................................................... 11 
Carefree Connects Mobile App ................................................................... 11 
FAQs..................................................................................................................... 13 
The Indicator Light Blinks on the BT12 Control Box. ................................... 13 
The System Beeps and the Awning Partially Retracts. ............................... 13 
The Remote Does Not Work ....................................................................... 13 
Manual Override .................................................................................................. 14 
Awning Care ........................................................................................................ 15 
Fabric Care.................................................................................................. 15 
Arm Noise.................................................................................................... 16 
Adjusting the Pitch....................................................................................... 16 
Carefree Major Product Limited Warranty......................................................... 17 
Before operating the awning, carefully review the Owner's Manual.
The manual contains important safety information, detailed operating
instructions, common maintenance procedures and other useful
information.

Carefree of Colorado
2
INTRODUCTION
Thank you for your recent purchase of the Freedom Freestyle RM awning. We
appreciate having the opportunity to do business with you. Our customers are
our top priority, and we strive for 100% satisfaction. If you have any questions or
concerns about this order, please do not hesitate to contact us.
Check with your dealer to discover the products that can make your life more Carefree.
The Carefree Freestyle RM awning is state of the art with lateral support arms that
provides strength and functionality without interfering with coach sidewalls, custom
graphics or equipment that may be mounted on the sidewalls.
When retracted, the housing provides protection against the elements while
the streamlined styling blends in with the RV sidewall and is a perfect
complement to other Carefree products.
The awnings are made with heavy duty construction including an all metal
chassis.
The BT12 Wireless Control System with Bluetooth®wireless technology
offers unique features not available with a standard awning installation.
Carefree Connects Mobile App – The app provides full and enhanced
control of the awning using a smart phone or tablet. The free app can
be downloaded on any devices that support: 1) Current iOS or Android
operating systems, and 2) Bluetooth low energy technology.
Full Retract – When the awning is retracted, it retracts completely. It is
not necessary to hold the button when closing the awning.
Full Extend – When the awning is extended, it extends completely. It is
not necessary to hold the button when opening the awning.
Auto-Retract – The awning can be set to automatically close when
windy conditions occur with the optional BT Motion Sensor.
Remote Control – The operator can conveniently operate the awning
from any location with the optional BT Remote key FOB.
Special Note: This manual provides a basic description of the product and the standar
d
operating controls provided by Carefree of Colorado. Some Original Equipmen
t
Manufacturers (OEM's) may alter or change the placement, style and/or functiona
l
configuration of the switches. If your controls do not match the style or description included,
contact the coach manufacturer for an accurate description.

FREESTYLE RM AWNING
3
NOTICES AND DISCLAIMERS
T RADEMARKS
The Bluetooth® word mark and logos are registered trademarks owned by the
Bluetooth SIG, Inc.
Use of such marks by Carefree of Colorado is under license.
Other trademarks and trade names are those of their respective owners.
S TATEMENTS OF C OMPLIANCE
●BT12 Control Module ●BT Motion Sensor ●BT Remote
FCC and IC identification numbers are located on the exterior surfaces of the
individual components.
FCC COMPLIANCE
These devices comply with Part 15 of the FCC rules. Operation is
subject to the following two
conditions: (1) These devices may not cause
harmful interference and, (2) These devices must accept any
interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IC COMPLIANCE
These devices comply with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) These devices may not cause
harmful interference and, (2) These devices must accept any
interference received,
including interference that may cause undesired operation.
Ces appareils sont conformes aux normes RSS exonérées de licence d'Industrie
Canada. L'opération est soumise aux deux conditions suivantes: (1) Ces appareils ne
doivent pas causer d'interférences nuisibles et, (2) Ces appareils doivent accepter toute
interférence reçue, y compris les interférences pouvant entraîner un fonctionnement
indésirable.

Carefree of Colorado
4
FCC/IC R ADIATION E XPOSURE S TATEMENT
●BT12 Control Module ●BT Motion Sensor
This equipment complies with FCC and IC radiation exposure limits for an uncontrolled
environment. The minimum distance between the radiator and people is designed to
be 20cm when installed and operated.
Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un
environnement non contrôlé. La distance minimale entre le radiateur et les personnes
est de 20 cm lorsqu'installé et utilisé.
●BT12 Remote
This equipment complies with FCC and IC radiation exposure limits for an uncontrolled
environment. The minimum distance between the radiator and people is designed to
be 5mm (excluding extremities: hands, wrists, feet and ankles) when operated.
Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un
environnement non contrôlé. La distance minimale entre le radiateur et les personnes
est de 5 mm lors de l'utilisation.
D ISCLAIMERS
The Freedom Freestyle RM awning, BT12 Wireless Awning Control System
and the Carefree Connects Mobile App are products of Carefree of Colorado,
located in Broomfield, Colorado, USA. The
information contained in or
disclosed in this document is considered proprietary to Carefree of Colorado.
Every effort has been made to ensure that the information presented in the
document is accurate and
complete. However, Carefree of Colorado assumes
no liability for errors or for any damages that result from
the use of this document.
The information contained in this manual pertains to the current components and
software listed on the title page. Carefree of
Colorado reserves the right to
cancel, change, alter or add any parts and procedures, described in this
manual, without prior notice.
Carefree of Colorado agrees to allow the reproduction of this document for use
with Carefree of Colorado
products only. Any other reproduction or translation
of this document in whole or part is strictly prohibited
without prior written
approval from Carefree of Colorado.
S ERVICE AND S UPPORT
www.carefreeofcolorado.com
www.carefreeofcolorado.carefreeconnects
[e-mail]
Carefree of Colorado
2145 W. 6th Ave.
Broomfield, CO
80020

F REESTYLE RM A WNING
5
Warnings and Cautions
This is the safety alert symbol. It is used to alert individuals to
potential personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible personal injury or death.
WARNING This product can expose you to chemicals including
Di-isodecyl phthalate (DIDP), Vinyl Chloride and Formaldehyde, which are
known to the state of California to cause cancer or birth defects or other
reproductive harm. For more information visit www.P65warnings.ca.gov
WARNING Risk of fire. Keep all sources of heat and
flame away from the awning canopy. Fabric is NOT fireproof.
NOTICE Awnings are designed to provide shade and protection from the
sun. The effects of wind and rain on an awning are unpredictable and can cause
severe damage to the awning and/or the vehicle. If wind or extended periods of
rain are expected, roll up the awning.
NOTICE It is recommended that if leaving the RV unattended for a
length of time, retract the awning to avoid unexpected weather conditions.
NOTICE The Freestyle RM awning is a free-standing (self-supporting)
lightweight awning with auto retraction. Do not hang items from the
awning or use tie down devices. Use of such objects can cause serious
damage to the awning that is not covered by warranty.
NOTICE If installed, LED lighting must be turned off when the awning
is in the rolled up position. This is to prevent possible damage to the LEDs
and/or canopy.
NOTICE When the awning is in the retracted (rolled up) position, shut
off the power switch to avoid accidentally extending the awning. For
safety, the power switch must be turned off before moving the RV.
Additional Cautions and Notices are included in the text for the proper operation
of the awning.

Carefree of Colorado
6
O PERATION
The BT12 Wireless Awning Control System offers multiple methods of operating
the awning: standard switch operation, the Carefree Connects Mobile App (see
page 11) and the BT Remote (see page 9).
S TANDARD S WITCH O PERATION
To Operate the Awning:
Press the power switch to ON.
I
MPORTANT N OTE :The power switch must be on for the extend/retract
functions to be active using the standard switch operation, the Carefree
Connects Mobile App and the BT Remote. The optional BT Motion Sensor
is disabled when the switch is OFF.
To OPEN : Press and release the extend switch. The awning will open completely.
To interrupt the awning motion, press and release the extend switch again.
The awning will stop.
To
CLOSE the awning: Press and release the retract switch. The awning will
close completely. To interrupt the awning retraction, press and release the
retract switch again. The awning will stop.
When the awning is in the retracted (rolled up) position, shut off the power
switch to avoid accidentally extending the awning.
I GNITION L OCKOUT
The BT12 Control System provides two options for transportation safety using
ignition lockout.
Standard - The system disables the extend function while the vehicle ignition key is
in the ON position.
RTL – The system fully retracts the awning and disables the extend function when the
vehicle ignition key is in the ON position.
Functions will return to normal operation when the ignition key is turned OFF.
Contact your vehicle dealer to find out if you have the ignition lockout option
connected and which version is active in your vehicle.

FREESTYLE RM AWNING
7
BT M OTION S ENSOR
The BT Motion sensor detects awning motion caused by windy conditions. The
sensor is located inside the lead rail on the LH (motor) side.
The system operates by gauging the motion of the awning's front edge (roller tube).
When the motion exceeds the factory preset threshold the system retracts the awning.
The factory default is “3” on a scale from 1 to 5; 5 being the most sensitive. When using
the mobile app, the sensitivity can be adjusted for personal preference.
NOTICE The Carefree auto retract system is a premier electronic auto-
retract system that provides protection against adverse elements; but no auto-
retract system is a guarantee against severe or destructive weather; the effects
of wind and rain on an awning are unpredictable and may cause severe damage
to the awning and/or vehicle. If wind or extended periods of rain are expected,
roll up the awning.
NOTE: The auto-retract system is ON when the power switch is ON. The system is
OFF when the power switch is set to OFF. If the power is shut off with the power switch
while the awning is extended, the awning is not protected by the auto-retract system.
If the motion sensor batteries are low, the awning will beep every 30 seconds
(when the power switch is ON) and the awning will partially retract. This will
continue until the batteries are replaced. The awning will operate normally after
the batteries are replaced.
BATTERY REPLACEMENT –ORIGINAL CONFIGURATION
The motion sensor uses two (2) 675 batteries. Batteries are available at local
battery outlets.
1. Open the awning to access the BT12 Motion Sensor.
2. Pull the thumb tab of the bracket away from the module and lift the module
out of the bracket. It is not necessary to remove the mounting bracket.
3. Remove the two screws and the rear cover.
4. Replace the two batteries. Match the new battery orientation with the old batteries.
5. Replace the cover and screws.
6. Snap the module into the mounting bracket. The module will only fit one
way in the bracket.
BT017
Remove Screws
and Rear Cover
Match Battery
Orientation
675 Batteries
(x2)
Thumb
Tab
SIDE
DOWN
675

Carefree of Colorado
8
BATTERY REPLACEMENT –CURRENT CONFIGURATION
The motion sensor uses two (2) “AAA” alkaline batteries. Batteries are available
at local battery outlets.
7. Open the awning to access the motion sensor that is located in the lead rail on the
motor side of the awning.
8. Remove the sensor module from the awning.
9. Remove the screws and the rear cover.
10. Remove the two batteries.
11. Make sure that the contact tabs are clean and bent out for best contact.
12. Insert new batteries. Match the new battery orientation with the old batteries.
Tip: Place the battery end next to the PC board first then swivel the other end into
the case. This will set the batteries firmly into the case.
13. Check that the seal is in place and flat then attach the rear cover with the
screws removed previously.
14. Install the module back in the awning.
BT017a
Remove Screws
and Cover
Remove Old Batteries
Insert New Batteries
Insert These
Ends First
PC Board (ref)
Remove Screws and
Motion Sensor From Bracket
Seal (ref)

F REESTYLE RM A WNING
9
O PTIONS
The BT12 Wireless Control System offers several options to enhance your
awning experience. OEM’s may install these options as a standard offering or
can be added to your system at a later date. Contact your Carefree dealer about
these options.
BT R EMOTE
The optional BT Remote provides the advantage of allowing you to operate the
awning from any convenient location.
The remote has an operating range of approximately 30 feet. Actual distance may vary
depending on the installation, and proximity of obstacles (such as other vehicles, wall
construction etc.)
Extend Press and release the extend button
once to activate the extend function
(the motor will beep once).
Press and release a second time to
extend the awning. The awning will
extend out to the full extension and
stop automatically.
Retract Press and release. The awning will
retract and stop automatically when
the awning is fully retracted.
LED Controls
The LED controls are for white LED’s wired through the BT12 Control Module.
Turn the awning lights switch to ON (refer to page 9).
The remote ON/OFF button allows you to turn the awning lights on and off (the
awning lights switch must be on).
Press and hold the LED Bright/Dim buttons to adjust the LED brightness level.
B
ATTERY R EPLACEMENT
The remote uses one (1) CR2032 battery; batteries are available at local battery
outlets.
1. Carefully remove the back cover
using a coin in the slot at the bottom
corner of the remote.
2. Remove the old battery and insert a new
battery with the “+” terminal facing up.
3. Snap the back cover on.
CR2032
Coin
Slot
Remove Back Cover
Replace Battery
Match Battery
Orientation
BT008

Carefree of Colorado
10
LED’ S
White (monotone) LEDs are a popular option providing lighting beneath the
awning. Factory installed LEDs are located in the lead rail.
The BT12 Control System provides controls to allow you to set the lights to
match your preference with ON/OFF and dimming controls through the Carefree
Connects Mobile App and/or the BT Remote.
To operate the White LED lights, you must have the awning
lights switch ON.
NOTE: Some OEMS may furnish their own switch that may
appear differently than the switch pictured or may have the
LED’s operated through a multiplexing control center.
The factory default for the lights is full bright. When the
light is adjusted with the BT Remote or the mobile app, the
system will remember the setting for the next time the lights
are turned on.
RGB
(C OLOR ) LED S
Select OEMs may offer RGB LEDs. These are NOT controlled through the BT12
Control System.
These lights use a separate IR (Infrared) remote and sensor. The top of the
remote must be pointed at the infrared sensor on the LED receiver module.
The remote control provides:
Simple push button on/off
Adjustable dimming
15 color choices + white
Special effects
(flash, strobe, fade and smooth)
Dim OFF/ON
Color
Select Special
Effects
LEDRGB003
OFF ON
WRGB
FLASH
STROBE
FADE
SMOOTH

F REESTYLE RM A WNING
11
S ETTING THE S YSTEM INTO P AIRING M ODE
Peripheral devices (such as remotes and smart devices with the Carefree Connects
app) must be paired to the BT12 Control Module.
There are two methods to set the system into pairing mode.
Using the Awning Retract Function:
1. Turn power to the awning ON.
2. Extend the awning. Note that the awning
does not have to be opened completely.
3. Retract the awning.
4. When the awning is fully retracted, press
and hold the retract switch for 3 seconds
and release.
The awning is now in pairing mode for 5
minutes.
5. The BT12 control module will automatically
pair to the device then go to working mode.
Using the Switches:
1. Turn the awning power switch to OFF.
2. Press and hold the extend switch.
3. While holding the extend switch, turn the power switch ON.
4. Continue to hold the extend switch for 3 seconds, then release.
NOTES:
The awning will remain in pairing mode for 5 minutes.
The module will pair to the physically closest unpaired device first. Repeat
the pairing steps for each additional device.
Refer to the Carefree Connects Mobile App manual for setting up and
pairing a smart device (such as a smart phone or tablet).
Multiple peripheral devices can be paired to the awning (maximum of 8).
oOnly one active BT Motion Sensor can be paired to the control module.
oOnly one active BT Remote can be paired to the control module.
oMultiple mobile devices (smartphone or tablet) can be paired to the
control module but only 1 can be active at a time.

Carefree of Colorado
12
C AREFREE C ONNECTS M OBILE A PP
The Carefree Connects Mobile App allows you to interact with your awning(s)
from your mobile device. The app provides access to enhanced features and
additional options. The mobile app may be used on any device that supports
current iOS or Android operating systems and Bluetooth low energy technology.
For personalized operation controls visit your app store for your smart phone or
tablet and download the free Carefree Connects Mobile App.
Download the Carefree Connects Mobile App manual at
www.carefreeofcolorado.com
The Carefree Connects Mobile App provides programmable controls and status
readings for:
Real-time open and close with the touch of a button.
Power your LED lights ON or OFF and adjust the LED brightness.
View the health of your awning and review status notifications.
Name your awning(s). Avoid confusion by having each awning identified with a
unique name.
Adjust the motion sensitivity level for wind retraction.
Multiple devices can be paired to the awning up to a maximum of 8
peripheral devices.
IMPORTANT NOTE:The power switch (see page 6) must be on for the
extend/retract functions to be active using the standard switch operation, the
Carefree Connects Mobile App and the BT Remote. The BT Motion Sensor is
disabled when the switch is OFF.

FREESTYLE RM AWNING
13
FAQS
T HE I NDICATOR L IGHT B LINKS ON THE C ONTROL B OX .
oThe indicator light on the control module
shows the function status of the control
module.
oSolid ON indicates power is supplied to the
control module.
oOne long blink and one short blink indicates
power and 1 peripheral (i.e. remote) is paired to
the module.
oThe module does not blink for being paired to a
mobile device with the Carefree Connects
Mobile App.
T HE S YSTEM B EEPS AND THE A WNING R ETRACTS .
oThe motion sensor batteries are low, the awning will beep every 30 seconds
(when the power switch is ON) and the awning will partially retract. This will
continue until the batteries are replaced. The awning will operate normally
after the batteries are replaced. Battery replacement is described on page 7.
T HE R EMOTE D OES N OT W ORK
Confirm that the remote is paired. The module indicator light will blink when
peripherals are attached (see description above).
In the mobile app on the “Peripherals Page” confirm that the remote is connected.
Green indicates the remote is connected, red indicates device is paired but not
connected. No listing indicates the remote has not been paired.
oRemote not paired. Refer to page 11 to pair the device.
oRemote is paired but not active. The remote has an approximate operating
range of 30 feet depending on obstructions (such as walls and other
vehicles). Move closer to the awning and control module.
oRemote is paired but not active. Batteries need to be replaced. Battery
replacement is described on page 9.
BT023
Indicator
Light

Carefree of Colorado
14
MANUAL OVERRIDE
If power to the vehicle is not available, the awning can be safely retracted using
the manual override located on the idler (right) end of the case.
There are two configurations of the Freestyle
RM. The original configuration is identified by
the five (5) screws in the endcap. The current
configuration has 1(one) screw in the endcap.
NOTE: This procedure cannot be used to extend the awning.
O RIGINAL C ONFIGURATION
15. Remove the plug from the right
endcap and save.
16. Insert a 3/8" socket drive extension
and handle into the square drive
hole inside the end cap.
17. Turn the handle clockwise until the
awning is retracted.
18. Reinstall the plug
C URRENT C ONFIGURATION
1. Remove the right outer endcap
and save.
2. Insert a 3/8" socket drive
extension and handle into the
square drive hole inside the
inner end cap.
3. Turn the handle clockwise until
the awning is retracted.
4. Reinstall the outer cap.
NOTICE After closing the awning with the manual override, the lead rail
may move out from the case 1/4" -1/2". This is normal and the awning is secure
for travel until power is restored or repairs are completed. Do not attempt to
force the lead rail in with the override, serious damage can occur to the awning.
Original Current
RMF046
RMF019a
3/8" Socket
Drive Extension
Remove
Cover
Remove Plug
RMF019
3/8" Socket
Drive Extension

FREESTYLE RM AWNING
15
AWNING CARE
Maintaining a Carefree Awning is easy. Just follow these basic steps:
Always operate the awning according to the instructions.
Periodically check that the fasteners are tight. Tighten if necessary.
Keep the awning fabric and arms clean.
F ABRIC C ARE
NOTICE Do not use oil based cleaners or any caustic, granulated, or
abrasive type cleaners on your Carefree product.
1. One of the best ways to keep the fabric looking good and to delay the need
for deep or vigorous cleanings is to hose fabrics off on a monthly basis with
clear water. This practice will help prevent dirt from becoming deeply
imbedded in the fabric. In most environments, a thorough cleaning will be
needed every two to three years.
2. When it’s time for a thorough cleaning, the fabric can be cleaned while still
on the awning frame.
For Vinyl Fabric – Use a soft brush and warm water with soap.
For Acrylic Fabric – Use a stiff brush and warm water with soap.
3. When cleaning the fabric, it is important to observe the following:
Always use a natural soap, never detergent.
Water should be cold to lukewarm, never more than 100F.
Air-dry only. Never apply heat to the fabric.
Always allow the fabric to dry thoroughly before rolling up the awning.
MILDEW
Mildew is a fungus growth that looks like dirt. Vinyl coated polyester fabrics are mildew
resistant because of a chemical biocide in the vinyl coating. Under ordinary conditions,
mildew will not appear. However, in areas where high temperature and humidity are
common, mildew can be a problem and requires the material to be washed more
frequently. Thoroughly rinse the fabric and allow to air dry before retracting the awning.
POOLING
When water collects on the top of the fabric, this is known as "pooling". This can occur
during inclement weather or if a running air conditioner discharges over the awning.
The water is dumped when the awning is retracted. It is recommended that if water
accumulates; retract the awning in steps (8"-12") to dump the water. This will help
prevent the fabric from stretching or distorting.
LEAKING
On vinyl canopies, side hems and poly cords are stitched in with a sewing
machine. On occasion, this stitching may allow water to seep or leak through the
stitches. This is normal and not a defect covered by warranty. Treat the seams
with a quality seam sealer.

Carefree of Colorado
16
A RM N OISE
After a period of use, the arm knuckle joints may slide together slightly making a
squeaking or squealing noise; this is normal and not a reason for concern. To reduce
the sound, apply a few drops of multi-purpose oil (3-IN-1®1or equivalent) on the
knuckle joint seams. Operate the awning and repeat 3-4 times to allow the oil to
penetrate into the joint.
A DJUSTING THE P ITCH
The awning opens and closes with a steep pitch. On low profile vans, the
leading edge of the awning may hit the top of the sliding door if the door is open
while extending or retracting the awning. To prevent this, the lower limit of the
pitch can be adjusted upwards.
NOTICE Use care to not raise the awning pitch to high. This can prevent
the lead rail from closing properly. If in doubt, try closing the awning, if the lead
rail does not close properly then lower the pitch.
1. Open the awning to access the adjustment screws located on the arm case
knuckles.
2. Have a second person lift up
on the lead rail to relieve the
pressure on the adjustment
screws.
3. Using a 4mm allen wrench,
loosen the top screw. Turn
the bottom adjustment screw
clockwise to raise the lead rail;
turn the adjustment screw
counterclockwise to lower the
lead rail.
4. When the pitch is set at the desired angle, tighten the top screw. Torque to 30 in-
lbs.
5. Repeat for each arm. Ensure that the lead rail is parallel with the awning
case.
NOTE: The Freestyle RM lead rail self-adjusts to accommodate the pitch. No
adjustment is required to the lead rail when the pitch is adjusted.
13-IN-1®is a registered trademark of the WD-40 company.
Loosen Top Screw when Adjusting
Tighten When Finished
Case
Knuckle
RMF038a
Lower Raise
Pitch Adjustment Screw

FREESTYLE RM AWNING
17
CAREFREE MAJOR PRODUCT LIMITED WARRANTY
Carefree of Colorado (hereafter referred to as Carefree) warrants to the first retail
Purchaser that the Carefree Product is free of defects in material and
workmanship within the terms and conditions as set forth in the warranty
statement available online at www.carefreeofcolorado.com. Carefree’s obligation
under this warranty is limited to the repair or replacement, at Carefree’s option, of
any defective component with new or factory refurbished components.
OWNER MUST RETAIN THE ORIGINAL PROOF OF PURCHASE AND/OR HAVE THE PRODUCT
WARRANTY REGISTRATION ON FILE AT CAREFREE FOR WARRANTY CLAIMS.
THIS WARRANTY IS NOT TRANSFERABLE.
Visit www.carefreeofcolorado.com for
- Warranty Duration;
- Warranty Coverage and Exclusions;
- Warranty Terms of Coverage; and,
- Warranty Claim Procedures
Register your Carefree products on-line at www.carefreeofcolorado.com
IMPORTANT NOTICE: It is strongly recommended that adjustments and repairs not
described in this book be performed by trained technicians at your Authorized
Carefree Dealer. Work performed by non-authorized persons or businesses may
void warranty.

Carefree of Colorado
18

FREESTYLE RM AWNING
19

070014-231r1 Printed in USA April, 2019
Carefree of Colorado www.carefreeofcolorado.com a Scott Fetzer company
Quality
Performance
Value
Style