Carimali ST-LINK/V2 Owner's manual

LB.05104.00
TECHNICAL
INSTRUCTIONS
LB-05104
.00
EDITION NOVEMBER 2015
EN
ENGLISH
ST
-
LINK/V2
P
ROGRAMMER
1
TECHNICAL
INSTRUCTIONS
.00
EDITION NOVEMBER 2015
ENGLISH
www.carima i.com

LB.05104.00 2

LB.05104.00 3
Introduction and General instructions
The programmer a ows to program the microprocessor on the disp ay-PCB
System Requirements OS:
•Windows NT (x86)
•Windows 2000 (x86)
•Windows XP (x86) with service pack 3 - a editions except Starter Edition
•Windows Vista (x86) with service pack 1 - a editions except Starter Edition
•Windows 7 (x86)
•Windows 7 (x86) Home Premium and Professiona Edition
Hardware Requirements:
-Computer that has a 1.0GHz or faster processor
-512 MB of RAM ( 1 GB recommended)
-2 GB of avai ab e hard disk space
-1 port USB 2.0
The KIT code 4. 5 93 includes:
a. USB pen drive containing the insta ation software on PC: STM32 ST-LINK Uti ity_v3.5
b. ST-LINK/V2 programmer board
c. F at cab e to connect the programmer to the disp ay-PCB
d. USB cab e to connect the programmer to the aptop
e. Technica manua LB.05104
a. b. c. d.

LB.05104.00 4
ST-LINK programmer installation
1. Insert the USB pen drive in the PC USB port and open the fo der
2. Carry out the STM32 ST-LINK Uti ity_v3.5 insta by c icking twice the icon
3. Confirm the first security advice
4. Wait unti the Preparing to Insta ends, then c ick Next

LB.05104.00 5
5. Wait unti License Agreement page appears, then c ick Yes
6. Wait unti Choose Destination Location page appears, then c ick Next
7. Wait the insta a tion unti the comp ete procedure ends, then c ick Finish

LB.05104.00 6
8. Wait We come to the Device Driver insta ation Wizard page appears, then c ick Next
9. Wait the procedure ends, then c ick End to exit
1. You wi have a new icon on your desktop

LB.05104.00 7
START ST-LINK/V2 programmer
1. Power the machine OFF
2. Remove the front part of the cup tray on top of the machine (3 screws)

LB.05104.00 8
3. Remove the disp ay-PCB protection (8 screws)
4. Connect the programmer to disp ay-PCB connector as shown by the picture

LB.05104.00 9
5. Power the machine ON
6. Turn ON your aptop and connect the ST-Link programmer to any USB socket
7. To run the programmer c ick on the new icon you have on your desktop: STM32 ST-LINK Utility
8. On the main pu down menu se ect Fi e end then Open fi e
9. Se ect the firmware to be up oaded on disp ay-PCB, fi e must be in BIN format, then c ick Open
Updated software re eases can be down oaded direct y from the reserved area of our website:
http://www.carima i.com/en/reserved_area/documents

LB.05104.00 10
10. On the main pu down menu c ick Target and then Option Bytes
Se ect the fo owing User configuration option byte, then confirm by c icking App y:
-WDG_SW
-nRST_STOP
-nRST_STDBY
11. On the main pu down menu c ick Target and then Automatic Mode

LB.05104.00 11
12. Once appears the Automatic Mode window, verify F ash programming have been se ected, then
se ect Verify whi e programming, fina y confirm with Start
13. You may verify the fo owing windows appears:
-Fu chip erase in progress…
-F ash memory programming…
14. Once the procedure ends the fo owing window appears. Disconnect the f at cab e from disp ay-PCB
and reassemb e machine, which is now ready to operate with new software

LB.05104.00 12
The Carimali product you have purchased is subject to Directive 2002/96/EC of the European
Parliament and the Council of the European Union on waste electrical and electronic equipment
(WEEE) and, in jurisdictions adopting that Directive, is marked as being put on the market after
August 13, 2005, and should not be disposed of as unsorted municipal waste. For further
information please contact Carimali.
The manufacturer reserves the right to change, without prior notice, the specifications of the
equipment illustrated in this publication; the manufacturer declines all responsibility for any
mistakes due to printing and/or typing errors contained in this publication.
All instructions, drawings, tables and information contained in this publication are reserved and
may not be reproduced entirely or in part or be communicated to a third party without written
authorisation from the manufacturer who holds exclusive rights.
REVISION TABEL DATE NOTE REVISED BY
LB-05104-00 05-11-2015 Prima Versione Giuliano Viola
The manager
Maurizio Boffelli
Firma del Responsabile della Documentazione