CARLO GAVAZZI Dupline G 3830 4445 User manual

Output M dule 4 x 20 Amp
G 3830 4445
User Manual
Brugermanual
CARLO GAVAZZI INDUSTRI A/S
Over Had tenvej 40, DK-8370 Had ten
Phone/Telefon: [phone]
Fax: [phone]
www.carlogavazzi.com/ac
Certified in accordance with ISO 9001
Kvalificeret i overensstemmelse med ISO 9001
MAN G38304445 rev. 10-03.08
15-029-214
4-channel receiver with 4 normally open contact outputs. Each output is
individually coded by means of the code programmer GAP 1605. For
changing the default setting, please refer to the datasheet on GAP 1605.
The outputs are normally OFF. When a transmitter coded to the selected
channel is activated, the output turns ON and remains ON until the
respective channel becomes deactivated. The default setting is such that
upon loss of Dupline®carrier all the outputs go OFF. If fail polarity is set
to 1, the relays will go on upon loss of carrier.
On the front of the module, it is possible mechanical to override each
relay. The LED’s will not follow manual override. The
manual override will be reset if Dupline or power is put off and on in min.
10 sec. Each relay is labled so it is possible to see the relays actual
status.
N te: At delivery some of the relays might be ON due to transportation
bumps. To be sure that the relays are OFF, connect the module to power
and Dupline and transmit on channels A1-4 once.
N te: Due to the construction with bistable relays, the module is intend-
ed for heating and light control only.
M de f Operati n
Wiring Diagram
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
12345678910 11 12 13 14 15 16
Power
supply
D+
1234
out out out out
1 2 34
D-
Du line
®
Fieldbus Installationbus
Dimensi ns
H8-housing
MAN G38304445.qxd:MAN G34304243 ENG-DA 25/03/08 11:32 Page 1

Output Specificati ns
Outputs 4 SPST relays
Contact ratings (AgSnO2) µ (micro gap)
Resistive loads AC1 20 A
In-rush current 120 A (20 msec.)
Max. switching voltage 440 VAC
Max. switching power 10 kVA
Capacitive load ≤200 µF
Lamp load ≤4800 W
Switching operations ≥60000 operations
Minimum load 100 mA/12 V
Max. Switching Frequency 2 Hz
Resp nse time ≤1 pulse train
Supply Specificati ns
P wer Supply Overvoltage cat. III (IEC 60664)
Rated operational voltage
Through term. 21 & 22 230 VAC, +/- 10% (IEC 60038)
Frequency 45 to 65 Hz
Rated operational power Typ. 2,5 VA
Max. power dissipation 7 W
Rated impulse withstand volt.
230 4 kV
Dielectric voltage
Supply Dupline®≥4 kVAC (rms)
Supply Outputs ≥4 kVAC (rms)
Dielectric voltage
Outputs Dupline®≥4 kVAC (rms)
General Specificati ns
Fail p larity state delay
Upon loss of Dupline®carrier ≤20 ms
P wer ON delay typ. 2s
Indicati n f r:
Supply ON LED, Green
Dupline®carrier LED, Yellow
Output ON LED, Red (one per output)
Envir nment
Degree of protection IP 20
Pollution degree 3 (IEC 60664)
Operating temperature -5 to +50°C (+23° to +122°F)
Storage temperature -50 to +85°C (-58° to +185°F)
Humidity (non-condensing) 20 to 80%
Mechanical resistance
Shock 5 G (11ms)
Vibration 2 G (6 to 55Hz)
H using H8-housing
Weight 500 g
Operati n Diagram
Dupline®Carrier
Transmission on channel for output 1
Output 1 (term. 25 & 26)
Transmission on channel for output 2
Power supply
Output 2 (term. 28 & 29)
MAN G38304445.qxd:MAN G34304243 ENG-DA 25/03/08 11:32 Page 2