CarShow DS-TY0710 User manual

Car Show Entertainment Systems Copyright 2012 All Rights Reserved
Multi-Media Navigation System Installation Guide Rev A
Installation Guide
* JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface.
NOTICE OF INTENDED INSTALLATION AND USE
THE CAR SHOW MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH
IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE
VEHICLE IS IN MOTION THROUGH A CONNECTION TO THE PARKING BRAKE.
THE INSTALLER OF THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS
WORKING PROPERLY PRIOR TO DELIVERY OF THE VEHICLE.
IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION
OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO
VIOLATE STATE AND/OR FEDERAL LAW.
CAR SHOW DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY
RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE.
STOP
Damage to the vehicle may occur
Do not proceed until process has been completed
CAUTION
CAUTION
Process must be carefully observed in order to reduce the
risk of damage to the accessory or vehicle
CRITICAL
Process must be carefully observed in order to ensure a
quality installation
TOOLS and EQUIPMENT
Specific tools and equipment recommended for this
process
SAFETY RISK
Observe safe practices, this process can be dangerous and
there is a risk of personal injury
TESTING and TROUBLESHOOTING
Content specific testing and troubleshooting points
DS-TY0710 Toyota Camry

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 2
PREPARING FOR THE INSTALLATION
Before you start, please read these critical steps below STEP
1
BEFORE YOU START THE INSTALLATION,
READ THIS GUIDE!
CHECK THE BATTERY
Test the battery voltage to make sure it’s fully charged to a
minimum of 12.8 VDC
This only takes seconds and can save hours of
troubleshooting later.
TURN THE VEHICLE
OFF
Keep the Vehicle Off during the installation to avoid setting
various Vehicle Fault sensors
Keep the Vehicle OFF during the
installation
Failure to follow this may cause the AIRBAG FAULT
SENSOR to become enabled. Dealer Service Departments
charge a significant fee to reset the Fault Sensor.

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 3
REMOVE THE FACTORY RADIO
*JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface
You will need to remove multiple interior trim components prior to removing the factory radio.
The following steps will help guide you through this process.
STEP
2
Carefully Remove Lower Dash Trim
Components
Use Caution, the plastic is fragile and excess force can
break or damage trim
CAUTION
Carefully Remove Lower Dash Trim
Components
Use Caution, the plastic is fragile and excess force can
break or damage trim.
CAUTION
Remove Upper Vent Trim
Use thin pry tool to carefully remove vent trim
Unplug Electrical Connections
Carefully unplug harness from back of vent assembly
Remove mounting screws
Remove 4 x 10mm bolts to remove radio

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 4
Unplug Electrical Connections
Carefully remove all harnesses from rear of OEM radio
*JBL Audio equipped vehicles will require additional part #
DP-TYJBL1 audio interface
Remove Factory Brackets/Clips
Remove factory brackets and clips from OEM radio
(8 x 10mm bolts 4 Left/4 Right)
Re-Install Factory Brackets/Clips on Car
Show Unit
Re-install factory brackets/clips on Car Show unit
(8 x 10mm bolts 4 Left/4 Right)
LOCATING REMOTE COMPONENTS
You will need to mount the GPS and Optional Satellite Radio Antennas on the exterior of the vehicle.
And mount the iPod Interface Connector in the vehicle. The following steps will help guide you
through this process.
STEP
3
Use Caution around SRS Components
It is the installer’s responsibility to ensure that the safety
equipment in the vehicle is NOT adversely affected by installation
of this system. Ensure that the routing of the harnesses do NOT
obstruct airbags, SRS or other safety devices.
Mount the GPS and Sat Radio antenna in a
location on the exterior of the Vehicle
Route the GPS harness away from other power harnesses in the
vehicle.
This will help to ensure optimum performance of the GPS
system.
CAUTION

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 5
“OPTIONAL”
Install the iPod interface connector in a
location accessible to the end-user
Locate the iPod interface module in an area which can be
serviced in the future.
The iPod cable is intended to be a serviceable item, which plugs
into the iPod/Sat radio Interface Module.
INSTALL THE CAR SHOW NAVIGATION SYSTEM
You will need to prepare the Car Show Navigation System for installation in the vehicle. STEP
4
Remove the DVD Transport Screws
There are 2 x Phillips Transport Screws which protect the DVD
Mechanism during transportation.
Transport Screws must be removed prior to installation.
Connect the Power and GPS Harnesses
The GPS Harness must be tightened with a WRENCH to ensure
it is properly seated.
Be sure to use white cable clamp to secure GPS antenna cable
Failure to follow this step may result in poor GPS signal
Connect Optional Harnesses such as iPod,
Satellite Radio, Camera, Reverse Sensors
These harnesses must be fully engaged prior to the system
installation.
See the Harness Diagrams for more information
Prepare the Vehicle side harnesses for
connection to the Car Show Harness
Use care not to pinch or damage cables as this will cause
performance issues/failures
CAUTION

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 6
CAUTION
Mount Car Show Navigation into Dash
Be sure to fully engage all connectors
Insert Car Show Navigation System Into Dash and mount
using OEM 4 x 10mm (2 Left/2 Right) screws
Re-install upper vent assembly and be sure to connect all
harnesses
Re-Install Lower Trim Components
Carefully re-install lower dash components
Verify Unit Operation
Power on unit to verify full operation
Insert a DVD to confirm the Video Disable
Circuit is properly Operating.
The Brake Wire must be connected to the Park Brake
Indicator Wire to complete a ground when the brake is
engaged.
ENABLE INSTALLER SETTINGS
You will need to select certain Installer Setting based on any Optional Equipment that you may have
installed
STEP
5
Launch the Installer Setting Screen
From any screen with the Menu Button, follow these steps
to display the Installer Setting Screen, select:
1) From any Screen, select “Menu”
2) From the Menu Screen, select “Settings”
3) Press “Keypad,” Press “7253” and “Enter”

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 7
Select the individual Settings as needed for
the installed components
Selectable options vary by product and installation. Select
the options as applicable for the installed optional
components.
Perform Pre-Delivery Tests
You will need to perform several Pre-Delivery Tests to ensure customer satisfaction
Some optional equipment may not be applicable
STEP
6
Turn the vehicle ON and System ON
Confirm the unit starts up properly
Troubleshooting
1) Reset the System while the Vehicle is ON
2) Confirm all connectors are properly installed
3) Check the Vehicle and System Fuses
Select RADIO as the Source
Confirm that the AM and FM reception are as expected
Troubleshooting
1) Confirm Antenna is properly connected.
2) Reset the System
Select SATELLITE RADIO as the Source
Confirm Channel 001 is present after ~5 minutes
Troubleshooting
1) Confirm the SAT Radio is Turned ON in the Installer Settings
2) Confirm the antenna has unobstructed view of the Sky
3) Confirm the antenna is located on the outside of the vehicle
Select iPOD as the Source
Confirm iPod is communicating and playback is OK
Troubleshooting
1) Confirm iPod Version Compatibility – not all are compatible
2) Confirm the harnesses are properly engaged
3) Reset the System

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 8
Select CD as the Source
Confirm CD audio playback is OK
Troubleshooting
1) Confirm the Disc is Store Bought and in good condition
2) Reset the system
Select DVD as the Source
Confirm DVD video playback is OK
Troubleshooting
1) Ensure the Park Brake is set to view video
2) Confirm the Disc is Store Bought and in good condition
3) Reset the system
Select MP3 as the Source
Confirm MP3 playback is OK – Select Favorites
Troubleshooting
1) Confirm that a Test Track exists in the Favorites Folder
2) Reset the system
Select Phone as the Source
Confirm Phone Pairing is successful
Troubleshooting
1) Confirm the Phone has BT and is in discoverable mode
2) Confirm the Phone is compatible with the system
3) Reset the system
Select NAV as the Source
Confirm the Navigation loads and signal strength is OK
Troubleshooting
1) Confirm the antenna has an unobstructed view of the sky
2) Confirm the antenna is located on the outside of the vehicle
3) Confirm the antenna connection is properly tightened
Select Reverse Camera
Confirm the backup camera screen shows in reverse
Troubleshooting
1) Confirm the Camera is set to ON in the Installer Settings
2) Confirm the Reverse Trigger wire is attached properly
3) Confirm the Camera is receiving 12VDC as required

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 9
Main Harness Diagram
Optional Harness Diagram

Car Show Installation Guide
Car Show Copyright 2012 All Rights Reserved
Installation Guide
Page 10
Option Harness Diagram
www.CarShowElectronics.com