cascade corporation Palm 6030844 Manual

For Technical Support . . . To Order Parts . . .
Call: 1-800-227-2233 Fax: [phone] Call: 1-888-227-2233 Fax: [phone]
Internet: www.cascorp.com Internet: www.cascorp.com
Write: Cascade Corporation, PO Box 20187, Portland, OR 97294 Write: Cascade Corporation, 2501 Sheridan Ave., Springfield, OH 45505
cascade
corporation
c
Setup
Instructions
Follow the steps below to use a Palm™handheld computer to
set up Force Control products. (Acceptable Models M125,
M130, Tungsten T2, T3, W, C, Zire 71.)
CAUTION: Keep Palm on charger when not in use. Com-
munications software will be lost if battery runs down. See
instructions on next page to configure
ptelnet1 software if
required.
1Connect the Palm to the system controller pigtail using
the Cascade adapter cable.
2Turn the Palm on and tap the ‘Home’ icon to see the
Cascade page with
ptelnet communications application
(‘computer screen’ icon).
3Tap the ptelnet icon.
4Tap the On button on menu bar that appears across
bottom of screen (‘On’ button highlights and blinking
cursor appears):
5Cycle the truck key ON/OFF, then ON. Palm screen may
show words ‘arm movement’.
6Press the Enter key (Palm ‘squiggly line’ note pad key on
RH side of Palm). Words ‘arm movement’ may appear.
7Press the Enter key again and follow the Force Control
prompts on-screen.
IMPORTANT: Enter key (‘note pad’ icon) is used for all
setup procedures when using the Palm. Use to cycle
through Force Control menus and to return to main menu.
8Use the Graffiti™writing area to enter data with the stylus
(preferred method) then press the Enter key.
9An alternate method of entering data uses the on-
screen keyboards shown opposite. Press the on-
screen Done button first, before pressing the Enter
key.
IMPORTANT: If the Enter key is pressed before the
on-screen Done button, the steps must be reentered.
It is not possible to back up in an AFC step or menu.
Palm™Setup Kit 6030844
for Force Control Products

  
AC0727.ill
Enter
(‘Note Pad’ Key)
Keyboard
Icons
Home (All
Applications)
On-Off
ptelnet
(Communications
Application)
‘Graffiti’
Writing
Area
    


AC0730.ill
3
2
6,7
8
Adapter Cable
(connect to
Force Control
controller pigtal)
Menu
Pull-Down 2
1 ptelnet V 0.6 shareware: Marcio Migueletto de Andrade at [email protected].
For more information refer to Palm documentation ‘Getting Started’ and ‘Read This First’.
qwe r t yu i op
asdfghjkl ; "
zcap x
shift space
cvbnm, .
-/
abc 23 IntÕlDone
AC0728.ill
$1
abc 123 IntÕlDone
£´
[]()
<>
/ =
@~&#
-+
/*
.,
space %
23
456
789
(0)
AC0729.ill
9
Part No. 6030841 R-4

Configuring Palm™communications
program ptelnet (if required)
Follow the steps below to configure ptelnet .
(If necessary to reload
ptelnet , use CD from Cascade or
obtain as freeware for the Palm.
CAUTION: Keep Palm on charger when not in use. Com-
munications software will be lost if battery runs down.
1Turn the Palm On and tap the ‘Home’ icon to see the
Cascade page with
ptelnet communications application
(‘computer screen’ icon). Tap the ptelnet icon.
2Tap the ‘scroll down’ icon located on the lower LH side
of the Palm to bring up the ‘Options / Edit’ menu shown
opposite.
3Tap Network and configure the screen as shown:
4Tap ‘scroll down’ icon again, then tap Serial and choose
one of the options shown based on the Palm model:
5Tap ‘scroll down’ icon again, then tap Terminal and
configure the screen as shown:
 
    
 
  
   
  
  
   
□
 
AC0734.ill
 
    
 
 
 
 
 
 
□

□

!
"#"
$% " & 
' ()
-OR-
-OR-
{
AC0733.ill
 
    


  
 
OK Cancel
127.0.0.1
23
10
10
AC0732.ill




















    
AC0731.ill 1
Scroll
Down Icon
On-Off
Home Icon
(Applications)
Options
menu
REF QTY PART NO. DESCRIPTION
6030844 Mobile Setup Kit
116031161 Palm Handheld
216031330 Cable, Palm-to-Force Control
316030842 ■Cable, Palm-to-Serial ●
416030691 ■Cable, Serial-to-Force Control
–16030840 ptelnet Communication Software
–16034054 ptelnet CD Backup
● Palm Part Number P10804U.
■May be substituted for 6031330.
Parts List
2
AC0743.ill
3
4
ADAPTER
CABLES
2
1
3

Capturing Force Control
Diagnostics Page
Follow the steps below to capture the Force Control Diag-
nostics Page as a ‘memo’ in the Palm computer. This
enables viewing the page or downloading (Palm ‘HotSync’)
to your PC.
1Cycle the Clamp through a CLAMP/HOIST cycle,
leave truck running. (current settings will be stored in
Diagnostics Menu in controller).
2Connect the Palm to the system controller pigtail using
the Cascade adapter cable.
3Turn the Palm On and tap the ‘Home’ icon to see the
Cascade page with
ptelnet communications applica-
tion (‘computer screen’ icon).
4Tap ptelnet, and tap On button on menu bar that
appears across bottom of screen (‘On’ button highlights,
blinking cursor appears):
5Tap the ‘scroll down’ icon located at the lower LH side
of the Palm character screen to bring up the ‘Options/
Edit’ menu shown opposite above.
6Tap ‘log’ and check ‘Active’ and ‘Log Header’ (oppo-
site), tap OK.
7Cycle the truck key ON/OFF, then ON. Palm screen
may show words ‘arm movement’.
8Press the Enter key (‘Note Pad squiggly line’ key on RH
side of Palm) and look for the words ‘arm movement’
9Press the Enter key again which brings up the Force
Control main menu. Select units, then select menu 3 -
Diagnostics Page (bottom right).
10 Tap the ‘scroll down’ icon to bring up the ‘Options/
Edit’ menu again (top right).
11 Tap ‘log’ again, uncheck ‘Active’ and ‘Log header’,
check ‘Hex dump’ (opposite). Tap OK. Turn
ptelnet
OFF by unhighlighting ‘On’ at bottom of screen:
12 Tap the ‘Home’ icon, locate and tap the ‘Memo Pad’
icon, which brings up the captured Diagnostics Page
(opposite) as the first new ‘memo’.
You can now view the Diagnostics Page on the Palm by
scrolling, or you can download (‘HotSync’) the page to
your PC. NOTE: PC must have Palm application
software to download the memo.




















    
AC0773.ill
Scroll
Down
Icon
On-Off
Home (All
Applications)
Icon
Options
menu
    


AC0730.ill
Log options
Ctl Esc Kbd VT Macros
□
Active
□
Log header
□
Hex dump
OK Cancel
On
AC0869.ill
    


AC0870.ill
❏Switch 1 Closed
❏Switch 2 Open
■Load Weight 2000 lbs.
❏Calculated Clamp Force 4000 lbs.
■Measured Clamp Pressure 1400 psi
■Calculated Clamp Pressure 1400 psi
■Clamp Force/Weight Ratio 14
❏Pulsewidth 2800
❏Hoist Pressure 800 psi
❏Calibrated Load Pressure 800 psi
❏Calibrated Attachment Pressure 800 psi
❏Trimpot 50
❏Measured Pressures 1,1,2,1
❏EEprom values 1,1,1,1,7,208,14,12,10
❏EEprom values 10,240,175,3,132,3,32
❏EEprom values 0,245,1,2,14,144,1,252
❏EEprom values 12,128,3,232,10,240,4,176
Enter
(‘Note Pad’ Key)
Log options
Ctl Esc Kbd VT Macros
□
Active
□
Log header
□
Hex dump
Cancel
On
OK
AC0874.ill
3
5
5
9,12

Do you have questions you need
answered right now? Call your
nearest Cascade Service Department.
Visit us online at www.cascorp.com
c
4-R1480306.oNtraP4002-54002noitaroproCedacsaC©
AMERICAS
Cascade Corporation
U.S. Headquarters
2201 NE 201st
Fairview, OR 97024-9718
Tel: 800-CASCADE (227-2233)
Fax: [phone]
Cascade Canada Inc.
5570 Timberlea Blvd.
Mississauga, Ontario
Canada L4W-4M6
Tel: [phone]
Fax: [phone]
Cascade do Brasil
Rua João Guerra, 134
Macuco, Santos - SP
Brasil 11015-130
Tel: [phone]
Fax: [phone]
EUROPE-AFRICA
Cascade Italia S.R.L.
European Headquarters
Via Dell’Artigianato 1
37030 Vago di Lavagno (VR)
Italy
Tel: [phone]
Fax: [phone]
Cascade (Africa) Pty. Ltd.
PO Box 625, Isando 1600
60A Steel Road
Sparton, Kempton Park
South Africa
Tel: [phone]
Fax: [phone]
ASIA-PACIFIC
Cascade Japan Ltd.
2-23, 2-Chome,
Kukuchi Nishimachi
Amagasaki, Hyogo
Japan, 661-0978
Tel: [phone]
Fax: [phone]
Cascade Korea
121B 9L Namdong Ind.
Complex, 691-8 Gojan-Dong
Namdong-Ku
Inchon, Korea
Tel: [phone]
Fax: [phone]
Cascade-Xiamen
No. 668 Yangguang Rd.
Xinyang Industrial Zone
Haicang, Xiamen City
Fujian Province
P.R. China 361026
Tel: [phone]
Fax: [phone]
Cascade India Material
Handling Private Limited
No 34, Global Trade Centre
1/1 Rambaugh Colony
Lal Bahadur Shastri Road,
Navi Peth, Pune 411 030
(Maharashtra) India
Phone: [phone]
Fax: [phone]
Cascade Australia Pty. Ltd.
1445 Ipswich Road
Rocklea, QLD 4107
Australia
Tel: [phone]
Fax: [phone]
Cascade New Zealand
15 Ra Ora Drive
East Tamaki, Auckland
New Zealand
Tel: [phone]
Fax: [phone]
Sunstream Industries
Pte. Ltd.
18 Tuas South Street 5
Singapore 637796
Tel: [phone]
Fax: [phone]