CAVE TeamUp A01 User manual

CAVE-TEK TeamUp A01 Camera User Guide
CAVE-TEK
TeamUp A01 Camera
User Guide
English (V1.0)

CAVE-TEK TeamUp A01 Camera User Guide
Table of content
1Packing List 1
2Quick Start 1
3About A01 2
3.1 Interfaces 2
3.2 Dimension 2
3.3 Remote Control 3
4GUI Settings 4
4.1 MENU 4
4.2 EXPOSURE 4
4.3 COLOR 5
4.4 IMAGE 5
4.5 Focus 5
4.6 NOISE REDUCTION 6
4.7 SETUP 6
4.8 RESTORE DEFAULT 6

CAVE-TEK TeamUp A01 Camera User Guide
1
1 Packing List
Open the box, you will find below items:
Name
Quantity
TeamUp A01 Camera
1
USB Cable
1
Remote Control
1
Quick Installation Guide
1
2 Quick Start
1) Please check below connections first.
2) Connect the PC’s USB to the USB connector on the rear panel of the camera.

CAVE-TEK TeamUp A01 Camera User Guide
2
3 About A01
3.1 Interfaces
Item
Name
1
HDMI Interface
2
USB 3.0 Interface
3.2 Dimension

CAVE-TEK TeamUp A01 Camera User Guide
3
3.3 Remote Control
Key Description
1. Standby Key
Press this button to enter standby mode. Press it
again to enter normal mode.
2. Number Key
To set preset or call preset.
3. *Key
To configure the special function key.
4. Preset Key
Set preset: Store a preset position.
[SET PRESET] + Numeric button (0-9): Setting a
corresponding numeric key preset position.
5. HOME Key
Confirm the selection, or move the camera back to
the middle position
6. Return Key
Return to the previous menu
7. Zoom Key
Slow Zoom: Zoom In [+] or Zoom Out [-] slowly
Fast Zoom: Zoom In [+] or Zoom Out [-] fast
8. Left/Right Setting Key
Press with 1 button and 2 buttons setting the
direction of the Pan-Tilt.
●Simultaneously press L/R Set +1[STD]: set the
Pan-Tilt to turn the same direction as the L/R
Set.
●Simultaneously press L/R Set +2[REV]: set the
Pan-Tilt to turn the opposite direction as the
L/R Set.
9. Focus Key
To adjust the focus.
Press [AUTO] adjust the focuses on the center of
the object automatically. Or to adjust the focus
manually.
Press [MANUAL] adjusts the focus on the center of
the object manual.
10. Selection Key
Press the button corresponding to the camera you
want to operate with the remote controller.
11. #Key
To configure the special function key.
12. IR Remote Control Key
[*]+[＃]+[F1]: Address 1
[*]+[＃]+[F2]: Address 2
[*]+[＃]+[F3]: Address 3
[*]+[＃]+[F4]: Address 4
13. Reset Key
Clear preset: Erase a preset position.
[CLEAR PRESET] + Numeric button (0-9)
Or: [*]+[#]+[CLEAR PRESET]: Erase all the preset
individually.
14. PTZ Control Key
Press arrow buttons to perform panningand tilting.
Press [HOME] button to face the camera back to
front.
15. Menu Key
MENU: enter or exit OSD MENU.
16. Backlight Key
BLC ON/OFF: Press this button to enable the
backlight compensation. Press it again to disable
the backlight compensation.
17. PTZ Reset Key
Preset Pan/Tilt self-test.
18. Special Function Key
[*]+[＃]+[1]: Change OSD menu to English
[*]+[＃]+[4]: Display current IP address
[*]+[＃]+[6]: Reset to system defaults
[*]+[＃]+[8]: Display camera firmware Info.
[*]+[＃]+[9]: set mounting mode (normal / vertical
flip)
[＃]+[*]+[4]: Set Network configuration to DHCP
[*]+[＃]+[Manual]: Reset network to default.
[*]+[＃]+[F1]: Assign Camera to IR Address 1
[*]+[＃]+[F2]: Assign Camera to IR Address 2
[*]+[＃]+[F3]: Assign Camera to IR Address 3
[*]+[＃]+[F4]: Assign Camera to IR Address 4

CAVE-TEK TeamUp A01 Camera User Guide
4
4 GUI Settings
4.1 MENU
Press the [MENU] button to display the main menu on the display, using the arrow button to move the
cursor to the item. Press the [HOME] button to enter the corresponding sub-menu.
MENU
Exposure
Color
Image
Focus
Noise Reduction
Setup
Information
Restore Default
[Home] Enter
[Menu] Exit
4.2 EXPOSURE
Move the main menu cursor to [EXPOSURE], and press [HOME] key enter the exposure page, as shown in
the following figure.
EXPOSURE
Mode
Auto
ExpCompMode
Off
Gain Limit
Off
Backlight
3
DRC
2
Anti-Flicker
50Hz
Select Item
Change Value
[Menu] Back
Mode: Exposure mode: Auto, Manual, SAE, AAE, Bright.
ExpCompMode: Exposure the compensation mode, On, Off (Effective only in Auto mode).
Gain Limit: Maximum gain limit, 0 ~ 15 (Effective only in Auto, SAE, AAE, Bright mode).
Backlight: Set the backlight compensation, On, Off (Effective only in Auto mode).
DRC: DRC strength, 0 ~ 8.
Anti-Flicker: Anti-flicker, Off, 50Hz, 60Hz (Effective only in Auto, AAE, Bright mode).

CAVE-TEK TeamUp A01 Camera User Guide
5
4.3 COLOR
Move the main menu cursor to [COLOR], and press [HOME] key enter the color page, as shown in the
following figure.
COLOR
WB Mode
Auto
AWB Sens
High
Saturation
100%
Hue
7
Select Item
Change Value
[Menu] Back
WB-Mode: White balance mode, Auto, Indoor, Outdoor, One Push, Manual, VAR.
AWB Sens: The white balance sensitivity, Low, Middle, High.
Saturation: 60% ~ 200%.
Hue: 0 ~ 14.
4.4 IMAGE
Move the main menu cursor to [IMAGE], and press [HOME] key enter the image page, as shown in the
following figure.
IMAGE
Luminance
6
Contrast
8
Sharpness
3
Flip-H
Off
Flip-V
Off
B&W-Mode
Off
Gamma
0.5
Style
Clarity
LDC
10
Select Item
Change Value
[Menu] Back
Luminance: 0 ~ 14.
Contrast: 0 ~ 14.
Sharpness: Auto, 0 ~ 15.
Flip-H: On, Off.
Flip-V: On, Off.
B&W-Mode: On, Off.
Gamma: Default, 0.45, 0.5, 0.56, 0.63.
Style: Norm, Clarity, Bright, PC, Clarity (LED), Face.
LDC: Off, -10 ~ 10.
4.5 Focus
Move the main menu cursor to [FOCUS], and press [HOME] key enter the focus page, as shown in the
following figure.
FOCUS
AF Sense
Low
Focus Area
Middle Area
[Menu] Back
AF Sense: Low, Medium, High.
Focus Area: Bottom Half, Middle Area, Upper Half, All.

CAVE-TEK TeamUp A01 Camera User Guide
6
4.6 NOISE REDUCTION
Move the main menu cursor to [NOISE REDUCTION], and press [HOME] key enter the noise reduction page,
as shown in the following figure.
NOISE REDUCTION
NR2D-Level
Off
NR3D-Level
3
Select Item
Change Value
[Menu] Back
NR2D Level: 2D noise reduction, Off, Auto, 1 ~ 5.
NR3D Level: 3D noise reduction, Off, 1 ~ 8.
4.7 SETUP
Move the main menu cursor to [SETUP], and press [HOME] key enter the setup page, as below.
SETUP
Language
EN
EPTZ
On
Zoom Limit
3x
DVI Mode
DVI
HDMI Format
1080p30
Tracking
Off
Select Item
Change Value
[Home] Enter
[Menu] Back
Language: EN, Chinese, Russian.
EPTZ: On, Off.
Zoom Limit: 1.5x, 2x, 3x, 4x, 8x (Effective only in EPTZ item to On).
DVI Mode: DVI, HDMI.
HDMI Format: 1080P30, 1080I60, 4K@30
Tracking: On, Off.
4.8 RESTORE DEFAULT
Move the main menu cursor to [RESTORE DEFAULT], and press [HOME] key enter the restore default page,
as shown in the following figure.
RESTORE DEFAULT
Restore?
No
Change Value
[Home] OK
[Menu] Back
Restore: Confirm restore factory settings, optional items: Yes, No.
Note: Press [HOME] button to confirm, all parameter restore default.